1
00:00:00,000 --> 00:00:02,430
Welcome to layer two of the OSI Model,

2
00:00:02,430 --> 00:00:04,050
the data link layer.

3
00:00:04,050 --> 00:00:05,130
In the data link layer,

4
00:00:05,130 --> 00:00:07,920
we're going to package up the bits we got from layer one

5
00:00:07,920 --> 00:00:09,330
and put those into frames,

6
00:00:09,330 --> 00:00:10,560
and then we're going to take those frames

7
00:00:10,560 --> 00:00:12,870
and transmit them throughout the network

8
00:00:12,870 --> 00:00:15,690
while performing some error detection, correction,

9
00:00:15,690 --> 00:00:18,960
identifying unique network devices using MAC addresses,

10
00:00:18,960 --> 00:00:21,150
and we're going to provide some flow control.

11
00:00:21,150 --> 00:00:24,240
Now a MAC address is a media access control address,

12
00:00:24,240 --> 00:00:27,390
which is a means for identifying a device physically

13
00:00:27,390 --> 00:00:30,240
and allowing it to operate on a logical topology.

14
00:00:30,240 --> 00:00:32,580
So when we started talking about physical topologies

15
00:00:32,580 --> 00:00:34,890
in the last lesson and the last layer,

16
00:00:34,890 --> 00:00:36,480
we dealt with things physically,

17
00:00:36,480 --> 00:00:39,690
but now we have to deal with things on a logical level.

18
00:00:39,690 --> 00:00:42,120
These MAC addresses are incredibly important

19
00:00:42,120 --> 00:00:45,180
for dealing with switches and other layer two devices.

20
00:00:45,180 --> 00:00:47,460
When it comes to identifying MAC addresses,

21
00:00:47,460 --> 00:00:49,320
every manufacturer of a network card

22
00:00:49,320 --> 00:00:52,470
assigns a unique 48-bit physical addressing system

23
00:00:52,470 --> 00:00:55,200
to every network interface card they produced.

24
00:00:55,200 --> 00:00:58,590
As you can see here, we have 12-digit hexadecimal numbers

25
00:00:58,590 --> 00:01:01,380
that are used to represent these MAC addresses.

26
00:01:01,380 --> 00:01:04,230
These MAC addresses are always written hexadecimally,

27
00:01:04,230 --> 00:01:05,940
where each of the letters or numbers

28
00:01:05,940 --> 00:01:08,070
is considered four bits.

29
00:01:08,070 --> 00:01:11,760
The first 24 bits, or the 6 letters as you can see here,

30
00:01:11,760 --> 00:01:15,240
identifies the particular vendor who made that card.

31
00:01:15,240 --> 00:01:19,470
In our example, we have D2:51:F1,

32
00:01:19,470 --> 00:01:21,240
and this is going to uniquely identify

33
00:01:21,240 --> 00:01:23,700
whichever person made this card.

34
00:01:23,700 --> 00:01:25,920
I like to think about this like a Social Security Number

35
00:01:25,920 --> 00:01:27,210
in the United States.

36
00:01:27,210 --> 00:01:29,010
If you look at the first three digits,

37
00:01:29,010 --> 00:01:31,020
it's going to identify the state and the year

38
00:01:31,020 --> 00:01:32,580
that person was born in.

39
00:01:32,580 --> 00:01:37,580
For instance, if my social security number was 123-45-6789,

40
00:01:37,890 --> 00:01:39,480
the first three digits might say

41
00:01:39,480 --> 00:01:40,980
when and where I was born.

42
00:01:40,980 --> 00:01:44,190
Maybe it was California in the year 1955.

43
00:01:44,190 --> 00:01:46,650
And that the rest of it, those other six digits,

44
00:01:46,650 --> 00:01:48,720
are going to uniquely identify me.

45
00:01:48,720 --> 00:01:50,310
Well, this is the same thing that happens

46
00:01:50,310 --> 00:01:51,390
with a MAC address.

47
00:01:51,390 --> 00:01:54,450
The first half of the MAC address, the first six digits,

48
00:01:54,450 --> 00:01:56,070
is going to tell us who made it.

49
00:01:56,070 --> 00:01:59,640
Was it made by Apple, Dell, Ralink, or whatever?

50
00:01:59,640 --> 00:02:02,550
The second half is going to represent the exact machine

51
00:02:02,550 --> 00:02:03,750
it belongs to.

52
00:02:03,750 --> 00:02:05,940
This is important for our logical topology

53
00:02:05,940 --> 00:02:07,710
because we can look at the MAC address

54
00:02:07,710 --> 00:02:10,530
and observe the flow of data going through our networks.

55
00:02:10,530 --> 00:02:11,460
And at this point,

56
00:02:11,460 --> 00:02:13,080
we don't really care how these devices

57
00:02:13,080 --> 00:02:14,550
are physically connected.

58
00:02:14,550 --> 00:02:17,430
The issue at that point is a level one issue.

59
00:02:17,430 --> 00:02:18,510
But now at level two,

60
00:02:18,510 --> 00:02:21,480
we care about whose turn it is to talk and transmit

61
00:02:21,480 --> 00:02:24,390
so other devices aren't talking over each other.

62
00:02:24,390 --> 00:02:26,280
For example, when I teach this course

63
00:02:26,280 --> 00:02:27,600
in a classroom environment,

64
00:02:27,600 --> 00:02:28,830
instead of all of the students

65
00:02:28,830 --> 00:02:30,540
shouting out their answers at once,

66
00:02:30,540 --> 00:02:32,760
we use a system of raising our hands.

67
00:02:32,760 --> 00:02:35,010
We wait for the teacher to call on one of the students,

68
00:02:35,010 --> 00:02:37,440
and then we can let them ask a question.

69
00:02:37,440 --> 00:02:39,540
This is how we control the information flow

70
00:02:39,540 --> 00:02:41,610
so that everyone can hear each other.

71
00:02:41,610 --> 00:02:44,130
In a network, we use electronic mechanisms

72
00:02:44,130 --> 00:02:45,720
to do this same thing.

73
00:02:45,720 --> 00:02:47,100
Now logical link control

74
00:02:47,100 --> 00:02:48,870
is going to provide connection services

75
00:02:48,870 --> 00:02:50,310
and allow your recipients

76
00:02:50,310 --> 00:02:52,500
to acknowledge the messages have actually gotten

77
00:02:52,500 --> 00:02:54,030
where you thought they were going.

78
00:02:54,030 --> 00:02:56,100
So for example, if I called up

79
00:02:56,100 --> 00:02:57,600
and I asked if you got my phone call,

80
00:02:57,600 --> 00:02:58,710
you could say yes

81
00:02:58,710 --> 00:03:00,450
and that would acknowledge the receipt of that

82
00:03:00,450 --> 00:03:02,790
and then we can move on to the next message.

83
00:03:02,790 --> 00:03:05,280
Logical link control does this for our networks,

84
00:03:05,280 --> 00:03:06,210
and because of this,

85
00:03:06,210 --> 00:03:09,060
it's the most basic form of flow control.

86
00:03:09,060 --> 00:03:11,490
Essentially, it's going to limit the amount of data

87
00:03:11,490 --> 00:03:13,110
that a sender can send at once

88
00:03:13,110 --> 00:03:16,050
and allow the receiver to keep from being overwhelmed.

89
00:03:16,050 --> 00:03:18,180
So if I go back to my classroom example,

90
00:03:18,180 --> 00:03:20,670
if I'm sitting there and I'm moving too quickly,

91
00:03:20,670 --> 00:03:22,267
a student might raise their hand and say,

92
00:03:22,267 --> 00:03:24,360
"Hey Jason, I don't understand this.

93
00:03:24,360 --> 00:03:26,190
Can you slow down and repeat it?"

94
00:03:26,190 --> 00:03:28,890
In the case of this video, you can just pause or go back

95
00:03:28,890 --> 00:03:30,150
and watch that part again.

96
00:03:30,150 --> 00:03:30,983
But in a classroom,

97
00:03:30,983 --> 00:03:33,570
they can't so they may ask me to repeat it.

98
00:03:33,570 --> 00:03:36,360
Logical link control, it similarly does the same thing,

99
00:03:36,360 --> 00:03:38,400
allowing a device to make this request

100
00:03:38,400 --> 00:03:40,560
for either less information at a time

101
00:03:40,560 --> 00:03:42,930
or to replay that information.

102
00:03:42,930 --> 00:03:44,760
Logical link control also gives us

103
00:03:44,760 --> 00:03:46,770
some basic error control functions,

104
00:03:46,770 --> 00:03:48,900
such as allowing the receiver to inform the sender

105
00:03:48,900 --> 00:03:51,000
if their data frame wasn't received

106
00:03:51,000 --> 00:03:52,860
or if it was received corrupted.

107
00:03:52,860 --> 00:03:55,230
And it does this by using a checksum.

108
00:03:55,230 --> 00:03:56,670
Now since everything it receives

109
00:03:56,670 --> 00:03:58,770
is just a series of ones and zeros,

110
00:03:58,770 --> 00:04:00,600
the receiver's going to add all of these up

111
00:04:00,600 --> 00:04:03,330
and the last bit will either be even or odd.

112
00:04:03,330 --> 00:04:05,880
If it matches, they add them all up and they're even,

113
00:04:05,880 --> 00:04:07,710
then it's going to assume that this was good

114
00:04:07,710 --> 00:04:10,530
if you had received a zero, meaning it was even.

115
00:04:10,530 --> 00:04:13,680
If the last bit was odd, meaning it was a one,

116
00:04:13,680 --> 00:04:14,820
and they added up all the numbers

117
00:04:14,820 --> 00:04:16,410
and they got an odd number,

118
00:04:16,410 --> 00:04:18,120
that means it was good as well.

119
00:04:18,120 --> 00:04:20,700
But if not, they can figure that something was bad

120
00:04:20,700 --> 00:04:23,850
and then ask for a retransmission of the frame.

121
00:04:23,850 --> 00:04:26,700
Now communication can be synchronized across layer two,

122
00:04:26,700 --> 00:04:29,160
according to three different schemes.

123
00:04:29,160 --> 00:04:31,410
We have something known as isochronous mode,

124
00:04:31,410 --> 00:04:32,520
which happens when the networks

125
00:04:32,520 --> 00:04:35,520
use a common reference clock, similar to synchronous,

126
00:04:35,520 --> 00:04:38,280
yet they also create time slots for transmissions,

127
00:04:38,280 --> 00:04:41,010
much like we did with time-division multiplexing.

128
00:04:41,010 --> 00:04:43,620
This has less overhead than either the other two modes

129
00:04:43,620 --> 00:04:46,080
because both devices know when they can communicate

130
00:04:46,080 --> 00:04:48,240
and for exactly how long.

131
00:04:48,240 --> 00:04:51,180
The second method we can use is known as synchronous method,

132
00:04:51,180 --> 00:04:53,670
and this is much like we use back in layer one.

133
00:04:53,670 --> 00:04:56,370
It's going to involve devices using the same clock,

134
00:04:56,370 --> 00:04:58,770
but the reason it's different from isochronous

135
00:04:58,770 --> 00:05:00,000
is that this is going to allow us

136
00:05:00,000 --> 00:05:01,680
to have beginning and ending frames

137
00:05:01,680 --> 00:05:03,990
and special control characters to tell us

138
00:05:03,990 --> 00:05:06,480
when we're going to start and when we're going to end

139
00:05:06,480 --> 00:05:08,190
based on those beats.

140
00:05:08,190 --> 00:05:10,290
For example, if I use in music,

141
00:05:10,290 --> 00:05:12,540
I have songs that have various time signatures,

142
00:05:12,540 --> 00:05:15,660
things like 3/4 or 4/4 timing.

143
00:05:15,660 --> 00:05:18,600
This tells us how many beats are in each measure.

144
00:05:18,600 --> 00:05:20,820
Our networks operate much the same way

145
00:05:20,820 --> 00:05:22,530
in that our devices can only communicate

146
00:05:22,530 --> 00:05:26,400
at frequency specified by these particular clock cycles.

147
00:05:26,400 --> 00:05:28,560
Because of this, there isn't a lot of gap time

148
00:05:28,560 --> 00:05:30,450
that isn't already properly utilized,

149
00:05:30,450 --> 00:05:33,720
and this becomes a major drawback for synchronized mode.

150
00:05:33,720 --> 00:05:36,060
And finally, of course, we have asynchronous,

151
00:05:36,060 --> 00:05:37,980
which is going to allow each of our network devices

152
00:05:37,980 --> 00:05:39,960
to reference their own clock cycles

153
00:05:39,960 --> 00:05:42,240
and use their own start and stop bits.

154
00:05:42,240 --> 00:05:44,310
In this way, there's no real control

155
00:05:44,310 --> 00:05:46,680
over when the devices are allowed to communicate though,

156
00:05:46,680 --> 00:05:49,050
and that becomes the major drawback here.

157
00:05:49,050 --> 00:05:50,760
Now when we look at layer two devices,

158
00:05:50,760 --> 00:05:53,100
we have things like network interface cards,

159
00:05:53,100 --> 00:05:54,900
bridges, and switches.

160
00:05:54,900 --> 00:05:57,450
In contrast to how a hub is a dumb machine

161
00:05:57,450 --> 00:05:59,280
that simply relies on a message coming in

162
00:05:59,280 --> 00:06:00,840
and repeating it back out,

163
00:06:00,840 --> 00:06:02,670
switches are smarter.

164
00:06:02,670 --> 00:06:04,290
They can actually use logic

165
00:06:04,290 --> 00:06:06,780
to learn which physical ports are attached

166
00:06:06,780 --> 00:06:09,420
to which devices based on their MAC addresses.

167
00:06:09,420 --> 00:06:11,220
And in this way, they can send data

168
00:06:11,220 --> 00:06:13,290
to specific devices in the network,

169
00:06:13,290 --> 00:06:15,660
allowing us to pick up and choose different lines

170
00:06:15,660 --> 00:06:18,060
of communication to go to different areas.

171
00:06:18,060 --> 00:06:20,640
Now we'll talk all about how this works

172
00:06:20,640 --> 00:06:22,290
and how these switches do this,

173
00:06:22,290 --> 00:06:25,200
including things like CAM tables using the MAC addresses

174
00:06:25,200 --> 00:06:26,460
and how they're doing the switching

175
00:06:26,460 --> 00:06:28,950
across the network in later lessons.

176
00:06:28,950 --> 00:06:30,360
And we'll go into depth in that

177
00:06:30,360 --> 00:06:32,040
because you will need to understand that

178
00:06:32,040 --> 00:06:34,140
to understand how networks really work.

179
00:06:34,140 --> 00:06:37,920
But for right now, just remember that switches, bridges,

180
00:06:37,920 --> 00:06:40,860
and MAC addresses are three great examples of things

181
00:06:40,860 --> 00:06:43,743
that operate at layer two, the data link layer.

