1
00:00:00,300 --> 00:00:02,490
Let's talk about wiring a network.

2
00:00:02,490 --> 00:00:04,470
So we talked about cable distribution,

3
00:00:04,470 --> 00:00:06,360
and I mentioned things like patch panels

4
00:00:06,360 --> 00:00:07,710
and how you're going to connect your switches

5
00:00:07,710 --> 00:00:09,870
and your routers through the patch panels,

6
00:00:09,870 --> 00:00:12,240
and that's going to connect back into your offices

7
00:00:12,240 --> 00:00:14,040
into that network wall jack.

8
00:00:14,040 --> 00:00:15,600
In this lesson, I'm going to show you

9
00:00:15,600 --> 00:00:17,160
how we wire up those devices

10
00:00:17,160 --> 00:00:18,930
and give you a hands-on look at them.

11
00:00:18,930 --> 00:00:19,950
Now you look at a patch panel,

12
00:00:19,950 --> 00:00:21,420
there are many different kinds of them.

13
00:00:21,420 --> 00:00:24,120
You'll notice that it has six different patch panel jacks,

14
00:00:24,120 --> 00:00:27,480
room to write down what it's being connected to above it.

15
00:00:27,480 --> 00:00:29,730
And if I flip this over to the other side,

16
00:00:29,730 --> 00:00:33,030
you'll see that it has what looks like a 110 block

17
00:00:33,030 --> 00:00:34,710
where you can punch down the cables

18
00:00:34,710 --> 00:00:36,300
onto the back of these jacks.

19
00:00:36,300 --> 00:00:40,200
And each of these, this is one, two, three, four, five

20
00:00:40,200 --> 00:00:42,330
and six, that gives us the six jacks

21
00:00:42,330 --> 00:00:43,440
that we see on the front.

22
00:00:43,440 --> 00:00:45,030
And it even shows you a nice little diagram

23
00:00:45,030 --> 00:00:47,610
of how you should be punching them down.

24
00:00:47,610 --> 00:00:49,920
Now, this is a very small patch panel.

25
00:00:49,920 --> 00:00:53,790
In fact, the one I'm holding my hand is only 12 big.

26
00:00:53,790 --> 00:00:55,200
So it has six here.

27
00:00:55,200 --> 00:00:57,060
And when I roll this all the way over,

28
00:00:57,060 --> 00:00:58,770
you could see the other six.

29
00:00:58,770 --> 00:01:01,680
Now, you'll also notice they have mount holes here

30
00:01:01,680 --> 00:01:04,440
because this is used inside server racks.

31
00:01:04,440 --> 00:01:06,570
This allows me to mount this into the server rack,

32
00:01:06,570 --> 00:01:08,490
as I'll show you at the end of this video,

33
00:01:08,490 --> 00:01:12,150
as it'll give you a nice clean, clear installation.

34
00:01:12,150 --> 00:01:13,920
Now if you work in a small office

35
00:01:13,920 --> 00:01:15,540
or a home office environment,

36
00:01:15,540 --> 00:01:17,730
you may not even be using something like this,

37
00:01:17,730 --> 00:01:20,820
but instead, you might be using something like this.

38
00:01:20,820 --> 00:01:23,757
And so as you can see here, both the punch down

39
00:01:23,757 --> 00:01:26,940
and the patch jack are both located on the front.

40
00:01:26,940 --> 00:01:29,130
Now, either is going to be the exact same thing.

41
00:01:29,130 --> 00:01:31,260
We have what looks like a punch down block,

42
00:01:31,260 --> 00:01:32,550
again, a 110 spacing

43
00:01:32,550 --> 00:01:34,740
because we're using five or above networks.

44
00:01:34,740 --> 00:01:36,720
And a network jack, that's RJ45

45
00:01:36,720 --> 00:01:38,430
for you to plug in a patch cable.

46
00:01:38,430 --> 00:01:41,430
So what will happen is the network jack from your office

47
00:01:41,430 --> 00:01:45,510
goes through the walls, comes in and gets punched down here.

48
00:01:45,510 --> 00:01:47,850
Then whatever is plugged in here,

49
00:01:47,850 --> 00:01:49,830
then gets patched into your switch.

50
00:01:49,830 --> 00:01:52,050
And I'm going to show you all of this in my rack

51
00:01:52,050 --> 00:01:53,400
in my server closet

52
00:01:53,400 --> 00:01:55,830
after we're done showing you how to do this punch down.

53
00:01:55,830 --> 00:01:57,750
So let's go ahead and do a punch down.

54
00:01:57,750 --> 00:01:59,430
I'm going to use this smaller block

55
00:01:59,430 --> 00:02:01,470
because it's a lot easier to film here,

56
00:02:01,470 --> 00:02:03,360
right here in this little workspace that we're using.

57
00:02:03,360 --> 00:02:05,280
So I'm just going to push this down over here

58
00:02:05,280 --> 00:02:07,890
and kind of go like this so hopefully you can see it better.

59
00:02:07,890 --> 00:02:10,590
And I'm going to punch down here on port number eight.

60
00:02:10,590 --> 00:02:13,650
You'll see that there are the eight punch down blocks

61
00:02:13,650 --> 00:02:15,840
and then the place for us to plug that jack in.

62
00:02:15,840 --> 00:02:18,690
Now before I do that, I have to get some cable.

63
00:02:18,690 --> 00:02:20,490
So I'm going to go to my bulk cable.

64
00:02:20,490 --> 00:02:22,230
I'm going to pull off a bunch of it

65
00:02:22,230 --> 00:02:26,550
and I'm going to cut it with my crimpers and gimme some cable.

66
00:02:26,550 --> 00:02:29,070
And now I'm going to go in here and I'm going to strip this wire.

67
00:02:29,070 --> 00:02:31,860
So I'm just going to go right around with my wire stripper,

68
00:02:31,860 --> 00:02:33,600
take off that outer jacket,

69
00:02:33,600 --> 00:02:37,410
and then I'm going to separate out those wires individually.

70
00:02:37,410 --> 00:02:38,610
And the nice thing about doing it

71
00:02:38,610 --> 00:02:40,260
on a punch down block like this,

72
00:02:40,260 --> 00:02:42,090
is I can use a lot of excess wire

73
00:02:42,090 --> 00:02:44,730
because my punch will remove the rest.

74
00:02:44,730 --> 00:02:45,690
Now, I'm going to go through

75
00:02:45,690 --> 00:02:47,160
and I'm going to straighten these out.

76
00:02:47,160 --> 00:02:48,810
I'll be right back.

77
00:02:48,810 --> 00:02:50,550
So I'm back here and what I've done

78
00:02:50,550 --> 00:02:52,440
is I've straightened out those wires

79
00:02:52,440 --> 00:02:53,820
and so they're ready to go.

80
00:02:53,820 --> 00:02:55,290
I also have my punch down tool,

81
00:02:55,290 --> 00:02:57,840
which is also conveniently part of my stripper.

82
00:02:57,840 --> 00:02:59,100
And it's right here at the end.

83
00:02:59,100 --> 00:03:01,230
You'll see this nice little sharp place.

84
00:03:01,230 --> 00:03:04,290
And so what's going to end up happening is as I go here,

85
00:03:04,290 --> 00:03:07,050
I'll go through and punch down my wire.

86
00:03:07,050 --> 00:03:11,160
So I'm just going to come over and pull the first wire over it

87
00:03:11,160 --> 00:03:14,500
and all you have to do to punch it down is simply insert it

88
00:03:17,220 --> 00:03:18,093
and push down.

89
00:03:19,830 --> 00:03:21,540
It's that easy. And now it's in.

90
00:03:21,540 --> 00:03:22,890
And then I'll go through the next one

91
00:03:22,890 --> 00:03:25,650
and I'll just continue to match up my color codes,

92
00:03:25,650 --> 00:03:27,480
punching them down as I go.

93
00:03:27,480 --> 00:03:30,390
Now I do have a pneumatic one as well,

94
00:03:30,390 --> 00:03:32,460
which uses a little bit more pressure.

95
00:03:32,460 --> 00:03:34,140
And with the pneumatic one,

96
00:03:34,140 --> 00:03:36,720
it will cut off those ends for me automatically.

97
00:03:36,720 --> 00:03:38,520
This one does not, so I'll have to go back

98
00:03:38,520 --> 00:03:41,040
and trim these ends off afterwards.

99
00:03:41,040 --> 00:03:43,080
But you get the idea here as you go through

100
00:03:43,080 --> 00:03:46,713
and you punch down according to the proper color code.

101
00:03:49,590 --> 00:03:52,680
And we'll just fix a second there as you go through.

102
00:03:52,680 --> 00:03:54,570
And we just continue to go through

103
00:03:54,570 --> 00:03:57,390
and punch them down in the appropriate colors.

104
00:03:57,390 --> 00:04:00,630
So you get the idea here as we're going to move on.

105
00:04:00,630 --> 00:04:02,700
So that's the way you do things with a punch down block.

106
00:04:02,700 --> 00:04:03,810
Now on the other end,

107
00:04:03,810 --> 00:04:05,850
you need it to be on your wall jack, right?

108
00:04:05,850 --> 00:04:07,710
Well, how do you do that?

109
00:04:07,710 --> 00:04:10,230
Well, you can go to the store and you can buy a wall jack.

110
00:04:10,230 --> 00:04:11,820
So for instance, here is one,

111
00:04:11,820 --> 00:04:16,019
it's a 110-Type Ivory Keystone wall jack, CAT 5e.

112
00:04:16,019 --> 00:04:17,250
Now once you open up the package,

113
00:04:17,250 --> 00:04:18,209
you're going to have three things.

114
00:04:18,209 --> 00:04:20,760
One is the actual card that came with the package itself.

115
00:04:20,760 --> 00:04:23,550
This tells me my wiring diagram in case you forgot it,

116
00:04:23,550 --> 00:04:27,630
the T568A and the T568B.

117
00:04:27,630 --> 00:04:29,460
On the other side of this, you're also going to have

118
00:04:29,460 --> 00:04:31,260
how it should look when you're done.

119
00:04:31,260 --> 00:04:34,830
And I'll show you this here, just like that.

120
00:04:34,830 --> 00:04:36,690
And you're going to have the keystone itself,

121
00:04:36,690 --> 00:04:38,400
which is where you're going to wire it in.

122
00:04:38,400 --> 00:04:41,550
And it tells you A and B right here on the side

123
00:04:41,550 --> 00:04:42,780
with the right color.

124
00:04:42,780 --> 00:04:46,770
So if we're doing A, the first pin is going to be green/white,

125
00:04:46,770 --> 00:04:50,250
two is going to be green, three is going to be orange/white,

126
00:04:50,250 --> 00:04:52,080
and six is going to be orange.

127
00:04:52,080 --> 00:04:54,870
If we're doing B, we're going to flop those around.

128
00:04:54,870 --> 00:04:56,160
On the other side, you're going to see

129
00:04:56,160 --> 00:04:59,100
that four, five, eight and seven are always going to be

130
00:04:59,100 --> 00:05:02,910
the same colors, blue, blue/white, brown and brown/white.

131
00:05:02,910 --> 00:05:03,743
And what we're going to do

132
00:05:03,743 --> 00:05:05,880
is do the same exact punch down technique we just did.

133
00:05:05,880 --> 00:05:08,790
And then we're going to cover it off with this little cap.

134
00:05:08,790 --> 00:05:12,690
So if I grab that cable, and I'm going to go ahead and grab it.

135
00:05:12,690 --> 00:05:14,220
And let's see, we're going to start out here

136
00:05:14,220 --> 00:05:16,440
with the brown/white on seven.

137
00:05:16,440 --> 00:05:19,020
So I'll grab my brown/white cable

138
00:05:19,020 --> 00:05:20,850
and I'm going to bring it in here.

139
00:05:20,850 --> 00:05:24,783
I'm going to take my punch down tool and I'm going to punch it.

140
00:05:26,310 --> 00:05:27,143
There we go.

141
00:05:27,143 --> 00:05:29,910
And then I'm going to do the same thing with brown,

142
00:05:29,910 --> 00:05:33,810
and continue to do that all the way across for all of those.

143
00:05:33,810 --> 00:05:35,730
Okay, so I finished wiring this one up,

144
00:05:35,730 --> 00:05:38,040
and as you can see, we have the extra excess wires

145
00:05:38,040 --> 00:05:41,490
hanging out on both sides and it just comes in like that.

146
00:05:41,490 --> 00:05:45,630
And we would then just close this up just like that.

147
00:05:45,630 --> 00:05:48,360
And we'd want to cut off all this excess wire.

148
00:05:48,360 --> 00:05:51,270
The tool I'm using, this is a very inexpensive

149
00:05:51,270 --> 00:05:52,320
punch down tool.

150
00:05:52,320 --> 00:05:53,190
If you have a much better one,

151
00:05:53,190 --> 00:05:55,470
it'll actually cut the wires as you're going.

152
00:05:55,470 --> 00:05:56,610
Now, once you have this keystone,

153
00:05:56,610 --> 00:05:57,660
what do you do do with it?

154
00:05:57,660 --> 00:05:59,070
Well, you want it to look like a wall jack.

155
00:05:59,070 --> 00:06:00,960
And so that's when we buy something like this,

156
00:06:00,960 --> 00:06:02,910
which again cost me a dollar.

157
00:06:02,910 --> 00:06:04,080
And so then you're going to take

158
00:06:04,080 --> 00:06:05,910
the wall jack and the keystone.

159
00:06:05,910 --> 00:06:07,680
And the keystone simply goes into it,

160
00:06:07,680 --> 00:06:10,590
and you can see that there's this little hole here

161
00:06:10,590 --> 00:06:13,500
and we just put it in place, squeeze it together.

162
00:06:13,500 --> 00:06:16,590
And now you have a network wall jack for your office

163
00:06:16,590 --> 00:06:18,240
that looks nice and professional.

164
00:06:18,240 --> 00:06:19,920
And again, you can make sure the colors all match.

165
00:06:19,920 --> 00:06:22,380
So you have ivory and ivory or white and white.

166
00:06:22,380 --> 00:06:23,280
But again, this was just something

167
00:06:23,280 --> 00:06:24,720
I was doing for a demonstration.

168
00:06:24,720 --> 00:06:26,970
So now that I showed you the basics, let's go see

169
00:06:26,970 --> 00:06:30,390
what the final product really looks like in the real world.

170
00:06:30,390 --> 00:06:33,240
So I'm going to take you over into my server room

171
00:06:33,240 --> 00:06:35,130
and we're going to take a look at one of our mini racks

172
00:06:35,130 --> 00:06:37,080
and you'll see that we have a patch panel there,

173
00:06:37,080 --> 00:06:39,030
and you'll see how everything is wired up nicely

174
00:06:39,030 --> 00:06:40,740
and how we have everything cabled away.

175
00:06:40,740 --> 00:06:42,600
And that's what you want your end product to look like.

176
00:06:42,600 --> 00:06:44,310
You want it to be nice and open,

177
00:06:44,310 --> 00:06:45,720
have all the cables out of the way,

178
00:06:45,720 --> 00:06:47,460
so good airflow can happen

179
00:06:47,460 --> 00:06:49,020
and you can always have everything labeled

180
00:06:49,020 --> 00:06:50,430
and know where things are going.

181
00:06:50,430 --> 00:06:51,480
Let's go take a look.

182
00:06:51,480 --> 00:06:54,480
So here you can see a small office rack.

183
00:06:54,480 --> 00:06:56,340
And again, this is a very small office rack

184
00:06:56,340 --> 00:06:59,250
because we're only supporting up to 24 wall jacks.

185
00:06:59,250 --> 00:07:02,010
Up here at the top, you're going to see that we have a switch

186
00:07:02,010 --> 00:07:03,270
and we have a patch panel.

187
00:07:03,270 --> 00:07:05,400
Now what you can see here on the left side,

188
00:07:05,400 --> 00:07:06,780
is that they are rack mounted

189
00:07:06,780 --> 00:07:08,670
and so they are screwed into the rack.

190
00:07:08,670 --> 00:07:10,500
Up here at the top is a patch panel,

191
00:07:10,500 --> 00:07:13,020
and I'm using these small six-inch cables

192
00:07:13,020 --> 00:07:15,810
going from the port that is going to the jack

193
00:07:15,810 --> 00:07:18,390
in this person's office or this other person's office.

194
00:07:18,390 --> 00:07:20,850
We have all of these 24 ports across the top,

195
00:07:20,850 --> 00:07:22,560
and then we have a 24-port switch.

196
00:07:22,560 --> 00:07:25,230
And so we just have it cabled up from port one

197
00:07:25,230 --> 00:07:28,560
to switch port one, switch port two to port two,

198
00:07:28,560 --> 00:07:29,910
and that will go through.

199
00:07:29,910 --> 00:07:32,370
Above this, you can't see it because of the cable,

200
00:07:32,370 --> 00:07:35,070
but it is labeled and it says, "This is Jason's office,"

201
00:07:35,070 --> 00:07:36,630
or, "This is Tamara's office,"

202
00:07:36,630 --> 00:07:38,430
or whoever's computer it's going to.

203
00:07:38,430 --> 00:07:40,290
Now, why would we want to use a patch panel

204
00:07:40,290 --> 00:07:42,780
as opposed to plugging directly into the switch?

205
00:07:42,780 --> 00:07:46,320
Now in our situation, we don't move offices very often,

206
00:07:46,320 --> 00:07:47,910
and so there's really no reason.

207
00:07:47,910 --> 00:07:49,710
We just did it because we like to.

208
00:07:49,710 --> 00:07:51,570
In a real office though, a lot of times

209
00:07:51,570 --> 00:07:54,030
people and equipment move all the time.

210
00:07:54,030 --> 00:07:56,370
And if you're going to be plugging and unplugging people

211
00:07:56,370 --> 00:07:58,770
to different switch ports and moving them around,

212
00:07:58,770 --> 00:08:01,320
you can actually break the switch ports.

213
00:08:01,320 --> 00:08:02,970
And you can't really replace

214
00:08:02,970 --> 00:08:04,740
these switch ports when they break.

215
00:08:04,740 --> 00:08:06,270
They're already inside this switch,

216
00:08:06,270 --> 00:08:09,780
and so I'm going to have to replace this 500 or $1,000 switch

217
00:08:09,780 --> 00:08:11,700
if one of these ports breaks.

218
00:08:11,700 --> 00:08:14,910
This patch panel on the other hand, costs about $50.

219
00:08:14,910 --> 00:08:18,210
And so if it breaks, I can simply switch out

220
00:08:18,210 --> 00:08:20,250
to a new patch panel very quickly

221
00:08:20,250 --> 00:08:22,050
and get the whole office back up and running.

222
00:08:22,050 --> 00:08:25,020
So it's just a matter of keeping your cost down

223
00:08:25,020 --> 00:08:26,880
and giving you the flexibility you need

224
00:08:26,880 --> 00:08:29,400
to be able to move things around whenever you need to.

225
00:08:29,400 --> 00:08:33,059
Proper wiring is always going to say you go from a switch

226
00:08:33,059 --> 00:08:35,850
to a patch panel and from the back of that patch panel,

227
00:08:35,850 --> 00:08:38,970
it's punched down and that goes to the back of a keystone

228
00:08:38,970 --> 00:08:40,289
which becomes a wall jack,

229
00:08:40,289 --> 00:08:42,539
just like I showed you inside this lesson.

230
00:08:42,539 --> 00:08:44,460
I hope you've enjoyed this behind-the-scenes look

231
00:08:44,460 --> 00:08:46,830
at how these patch panels and wall jacks

232
00:08:46,830 --> 00:08:49,950
and cable distributions are run inside a small office

233
00:08:49,950 --> 00:08:51,750
or a home office environment.

234
00:08:51,750 --> 00:08:53,580
Now again, you've been introduced to both kinds

235
00:08:53,580 --> 00:08:55,620
of patch panels, the front facing ones

236
00:08:55,620 --> 00:08:57,990
and the little single pieces that we showed you,

237
00:08:57,990 --> 00:09:00,360
as well as one of the rack-mounted patch panels

238
00:09:00,360 --> 00:09:02,460
as you saw in my own network.

239
00:09:02,460 --> 00:09:03,600
I hope you've enjoyed this

240
00:09:03,600 --> 00:09:05,333
and I'll see you in the next lesson.

