1
00:00:00,090 --> 00:00:01,770
In this lesson, we're going to cover

2
00:00:01,770 --> 00:00:03,990
four more network device commands,

3
00:00:03,990 --> 00:00:08,580
including show MAC address table, ARP, VLAN, and power.

4
00:00:08,580 --> 00:00:09,510
Let's go ahead and take a look

5
00:00:09,510 --> 00:00:11,760
at the show MAC address table first.

6
00:00:11,760 --> 00:00:13,380
The show MAC address table command

7
00:00:13,380 --> 00:00:15,000
is going to display the MAC address table

8
00:00:15,000 --> 00:00:17,490
on a Cisco switch, and this will provide the mapping

9
00:00:17,490 --> 00:00:20,340
of the MAC addresses to their corresponding ports.

10
00:00:20,340 --> 00:00:22,620
The show MAC address table command can be used

11
00:00:22,620 --> 00:00:24,270
for troubleshooting to help you identify,

12
00:00:24,270 --> 00:00:27,030
which devices are connected on which ports.

13
00:00:27,030 --> 00:00:29,520
When you enter the show MAC address table command,

14
00:00:29,520 --> 00:00:30,810
you're going to get a table displayed

15
00:00:30,810 --> 00:00:32,369
to your screen that will usually include

16
00:00:32,369 --> 00:00:33,960
four basic columns.

17
00:00:33,960 --> 00:00:36,630
The first column will be a BID or VLAN,

18
00:00:36,630 --> 00:00:38,790
which will show the bridge ID or VLAN associated

19
00:00:38,790 --> 00:00:40,350
with that particular device.

20
00:00:40,350 --> 00:00:42,330
The second column will be the MAC address,

21
00:00:42,330 --> 00:00:43,830
which will be the MAC address of the device

22
00:00:43,830 --> 00:00:46,110
connected on that specific switch port.

23
00:00:46,110 --> 00:00:48,750
The third will be the type of connection, and usually,

24
00:00:48,750 --> 00:00:50,190
this is going to be dynamic because

25
00:00:50,190 --> 00:00:51,930
it's going to dynamically read the MAC address

26
00:00:51,930 --> 00:00:53,970
from the card reported by the device

27
00:00:53,970 --> 00:00:56,070
when it connects onto that switch port.

28
00:00:56,070 --> 00:00:58,170
And then the fourth column is going to be the port,

29
00:00:58,170 --> 00:00:59,340
and this will list out the port

30
00:00:59,340 --> 00:01:03,090
being used by the switch, such as FA0/18

31
00:01:03,090 --> 00:01:06,150
if it was on port 18 of your switch.

32
00:01:06,150 --> 00:01:07,530
Next, we're going to take a look

33
00:01:07,530 --> 00:01:09,420
at the show ARP command.

34
00:01:09,420 --> 00:01:11,640
Now the show ARP command is going to be used

35
00:01:11,640 --> 00:01:13,800
to display the ARP table, which is the address

36
00:01:13,800 --> 00:01:16,920
resolution table inside of that device.

37
00:01:16,920 --> 00:01:18,990
This will show you the mapping of IP addresses

38
00:01:18,990 --> 00:01:20,400
to MAC addresses.

39
00:01:20,400 --> 00:01:22,410
This is going to be used to verify the IP addresses

40
00:01:22,410 --> 00:01:23,580
are being correctly mapped to the

41
00:01:23,580 --> 00:01:25,140
MAC addresses on your network,

42
00:01:25,140 --> 00:01:26,760
and you can use this if you suspect

43
00:01:26,760 --> 00:01:28,290
that ARP cache poisoning

44
00:01:28,290 --> 00:01:30,630
or ARP spoofing is occurring on your network,

45
00:01:30,630 --> 00:01:32,370
and you need to validate that to make sure

46
00:01:32,370 --> 00:01:33,930
the right IP addresses are being mapped

47
00:01:33,930 --> 00:01:36,090
to the correct MAC addresses and the type

48
00:01:36,090 --> 00:01:37,920
of connection that's being used.

49
00:01:37,920 --> 00:01:40,560
When you type in the show ARP command and hit enter,

50
00:01:40,560 --> 00:01:41,850
you're going to get a small table

51
00:01:41,850 --> 00:01:42,780
that's going to show up,

52
00:01:42,780 --> 00:01:45,210
which is going to give you the protocol, the address,

53
00:01:45,210 --> 00:01:48,060
the age, the hardware address, the type,

54
00:01:48,060 --> 00:01:49,290
and the interface.

55
00:01:49,290 --> 00:01:51,360
In the first column, we have the protocol.

56
00:01:51,360 --> 00:01:52,380
When it says internet,

57
00:01:52,380 --> 00:01:55,980
this means that we are using the IP or internet protocol.

58
00:01:55,980 --> 00:01:57,690
Second, we have the address,

59
00:01:57,690 --> 00:01:59,850
and this is the layer three type of address,

60
00:01:59,850 --> 00:02:02,520
and usually it's going to be in a dotted decimal notation

61
00:02:02,520 --> 00:02:06,090
if you're using IP version 4, as you can see here.

62
00:02:06,090 --> 00:02:08,150
The next column you have is the age,

63
00:02:08,150 --> 00:02:09,479
and this will show you the minimum age

64
00:02:09,479 --> 00:02:11,220
for this MAC binding.

65
00:02:11,220 --> 00:02:14,730
If it shows a dash, this means there is no minimum age.

66
00:02:14,730 --> 00:02:16,980
The next column we have is the hardware address,

67
00:02:16,980 --> 00:02:18,930
and this is going to be written as three groups

68
00:02:18,930 --> 00:02:22,560
of four hexadecimal digits, each one separated by a dot.

69
00:02:22,560 --> 00:02:24,000
Normally, when you see a MAC address

70
00:02:24,000 --> 00:02:25,980
being written down as a hardware address,

71
00:02:25,980 --> 00:02:28,290
you'll see it written as 12 characters grouped

72
00:02:28,290 --> 00:02:30,630
into two hexadecimal characters each,

73
00:02:30,630 --> 00:02:33,720
and each one being separated by either a dash or a colon.

74
00:02:33,720 --> 00:02:35,640
But when you're using the show ARP command,

75
00:02:35,640 --> 00:02:38,490
you'll see it written as three groups of four hexadecimal

76
00:02:38,490 --> 00:02:41,040
characters each separated by dots.

77
00:02:41,040 --> 00:02:42,540
The next column we have is the type,

78
00:02:42,540 --> 00:02:44,670
and if you see here, it says ARPA, that means that

79
00:02:44,670 --> 00:02:47,760
this is an internet protocol version four type of binding

80
00:02:47,760 --> 00:02:50,040
because we're using the ARPANET notation,

81
00:02:50,040 --> 00:02:52,470
which was the original version of the internet.

82
00:02:52,470 --> 00:02:54,870
And this also says which switch port is being used

83
00:02:54,870 --> 00:02:56,460
for this particular binding,

84
00:02:56,460 --> 00:03:00,060
and in this case we can see it's ethernet 0/0.

85
00:03:00,060 --> 00:03:03,540
The third one we have is known as show VLAN.

86
00:03:03,540 --> 00:03:05,550
Now, the show VLAN command is going to be used

87
00:03:05,550 --> 00:03:08,640
to configure the VLAN settings on a given switch.

88
00:03:08,640 --> 00:03:10,050
Now, it's going to be utilized to segment

89
00:03:10,050 --> 00:03:11,880
your network traffic for improved performance

90
00:03:11,880 --> 00:03:13,530
and security by creating all

91
00:03:13,530 --> 00:03:15,030
of your different VLANs.

92
00:03:15,030 --> 00:03:16,770
When you type in the show VLAN,

93
00:03:16,770 --> 00:03:17,730
you're going to be able to display

94
00:03:17,730 --> 00:03:19,793
the VLAN mappings on your particular device,

95
00:03:19,793 --> 00:03:21,960
and this will be shown in a series

96
00:03:21,960 --> 00:03:23,910
of four columns as well.

97
00:03:23,910 --> 00:03:25,350
When you deal with the four columns,

98
00:03:25,350 --> 00:03:26,940
you're going to have the VLAN number,

99
00:03:26,940 --> 00:03:28,530
you're going to have the name of the VLAN,

100
00:03:28,530 --> 00:03:29,520
you're going to have the status,

101
00:03:29,520 --> 00:03:30,900
and you're going to have the ports.

102
00:03:30,900 --> 00:03:33,720
In the first column, you'll have the VLAN identifier,

103
00:03:33,720 --> 00:03:37,350
which in this case shows one and 10 as my two VLAN.

104
00:03:37,350 --> 00:03:39,420
Then you'll see the VLAN names.

105
00:03:39,420 --> 00:03:42,720
The first one, which is VLAN 1, is the default VLAN,

106
00:03:42,720 --> 00:03:43,890
and that is how it is always set up

107
00:03:43,890 --> 00:03:45,840
on a Cisco device by default,

108
00:03:45,840 --> 00:03:48,000
and I do recommend you change VLAN 1

109
00:03:48,000 --> 00:03:49,500
from being the default into

110
00:03:49,500 --> 00:03:51,270
being something else as your default,

111
00:03:51,270 --> 00:03:53,990
such as VLAN 100, or VLAN 123,

112
00:03:53,990 --> 00:03:55,200
or something like that.

113
00:03:55,200 --> 00:03:57,960
That's harder for an attacker or hacker to guess.

114
00:03:57,960 --> 00:03:59,610
Next, we have the status column,

115
00:03:59,610 --> 00:04:01,920
and this will tell us if the VLAN is active or not.

116
00:04:01,920 --> 00:04:04,320
And then we have the ports associated with that VLAN.

117
00:04:04,320 --> 00:04:06,060
And here you can see the default VLAN

118
00:04:06,060 --> 00:04:07,980
has four ports associated with it,

119
00:04:07,980 --> 00:04:10,083
which is FA0/1/2/3 and /4.

120
00:04:12,390 --> 00:04:14,730
And then we have VLAN 10, which is going to be

121
00:04:14,730 --> 00:04:18,029
our user VLAN, which has three ports associated with it,

122
00:04:18,029 --> 00:04:21,930
FA0/5/6, and /7.

123
00:04:21,930 --> 00:04:23,460
The fourth and final command we're going to talk

124
00:04:23,460 --> 00:04:25,890
about is the show power command.

125
00:04:25,890 --> 00:04:27,750
Now, the show power command is going to be used

126
00:04:27,750 --> 00:04:30,330
to display and configure your power settings,

127
00:04:30,330 --> 00:04:32,760
particularly any devices that support PoE

128
00:04:32,760 --> 00:04:34,680
or power over Ethernet.

129
00:04:34,680 --> 00:04:36,120
By using the power command,

130
00:04:36,120 --> 00:04:36,953
we're going to be able

131
00:04:36,953 --> 00:04:39,240
to manage power distribution and troubleshoot any kind

132
00:04:39,240 --> 00:04:42,090
of power over Ethernet issues that might arise.

133
00:04:42,090 --> 00:04:43,800
When you type in the show power,

134
00:04:43,800 --> 00:04:46,710
you will get a table that shows you the power allocated,

135
00:04:46,710 --> 00:04:49,500
the power used, and the power available per port.

136
00:04:49,500 --> 00:04:51,720
In this example, you can see that I have a couple

137
00:04:51,720 --> 00:04:53,940
of different columns, including the interface,

138
00:04:53,940 --> 00:04:57,540
the admin, the oper, the power, the device,

139
00:04:57,540 --> 00:05:00,030
the class, and the max.

140
00:05:00,030 --> 00:05:01,350
When we deal with interface,

141
00:05:01,350 --> 00:05:03,360
this is going to be the switch port that we're talking

142
00:05:03,360 --> 00:05:07,620
about, such as FA0/1 or FA0/2.

143
00:05:07,620 --> 00:05:09,360
Under admin, you're going to see whether

144
00:05:09,360 --> 00:05:10,800
or not you're in automatic mode,

145
00:05:10,800 --> 00:05:13,050
which here you can see we are both set to auto,

146
00:05:13,050 --> 00:05:16,110
and for the oper, you can see if it's either on or off.

147
00:05:16,110 --> 00:05:20,010
In this case, you can see that the port at FA0/1 is on,

148
00:05:20,010 --> 00:05:22,380
and the port at FA0/2 is off,

149
00:05:22,380 --> 00:05:24,480
which means port one has power

150
00:05:24,480 --> 00:05:26,730
associated with it, but port 2 doesn't.

151
00:05:26,730 --> 00:05:27,960
We can see in the fourth column

152
00:05:27,960 --> 00:05:30,270
that this is a true statement, because we see the power

153
00:05:30,270 --> 00:05:33,690
of 15.4 watts is being shown on port 1,

154
00:05:33,690 --> 00:05:35,820
but we have a power of 0 on port 2

155
00:05:35,820 --> 00:05:37,980
because that port was turned off.

156
00:05:37,980 --> 00:05:40,080
Then we can see a short name for the device

157
00:05:40,080 --> 00:05:42,750
that's connected over PoE, and in this case,

158
00:05:42,750 --> 00:05:46,380
on port 1, we have an IP phone, there's a model 7960,

159
00:05:46,380 --> 00:05:49,740
which is a Cisco IP or voice over IP phone.

160
00:05:49,740 --> 00:05:51,940
If we look down at port 2, you can see NA,

161
00:05:51,940 --> 00:05:53,970
and that's because again, this switch port

162
00:05:53,970 --> 00:05:56,940
is currently off and not providing power to any devices,

163
00:05:56,940 --> 00:05:58,560
so that device can't be turned on,

164
00:05:58,560 --> 00:06:00,150
and reporting itself.

165
00:06:00,150 --> 00:06:02,040
The next column we have is class,

166
00:06:02,040 --> 00:06:04,920
and here you can see which class of PoE we're using,

167
00:06:04,920 --> 00:06:07,620
and in this case, on port 1 we're using class 2,

168
00:06:07,620 --> 00:06:09,000
and on port 2 since it's off,

169
00:06:09,000 --> 00:06:11,640
there is no class, or it is NA.

170
00:06:11,640 --> 00:06:13,530
The final column we have is max,

171
00:06:13,530 --> 00:06:15,720
and this tells us what is the maximum amount of power

172
00:06:15,720 --> 00:06:18,840
that can be supported by this PoE port on the switch,

173
00:06:18,840 --> 00:06:21,150
and in the case of both switch port 1 and 2,

174
00:06:21,150 --> 00:06:24,660
they are both set to a maximum of 15.4 watts.

175
00:06:24,660 --> 00:06:26,340
So, remember, for the exam,

176
00:06:26,340 --> 00:06:28,680
there are four additional network device commands

177
00:06:28,680 --> 00:06:29,880
that you should be aware of,

178
00:06:29,880 --> 00:06:31,800
and these are show MAC address table,

179
00:06:31,800 --> 00:06:35,160
show ARP, show VLAN, and show power.

180
00:06:35,160 --> 00:06:36,990
Show MAC address table is going to display

181
00:06:36,990 --> 00:06:39,060
the MAC address table on a Cisco switch,

182
00:06:39,060 --> 00:06:41,100
which shows the mapping of the MAC addresses

183
00:06:41,100 --> 00:06:43,140
to their corresponding switch ports.

184
00:06:43,140 --> 00:06:44,940
When you use the show ARP command,

185
00:06:44,940 --> 00:06:46,950
you're going to use this to display the ARP table,

186
00:06:46,950 --> 00:06:49,050
which includes the mapping of the IP addresses

187
00:06:49,050 --> 00:06:50,700
to the MAC addresses that are associated

188
00:06:50,700 --> 00:06:51,990
with that switch.

189
00:06:51,990 --> 00:06:53,790
When you use the show VLAN command,

190
00:06:53,790 --> 00:06:55,590
you're going to be able to see the VLAN settings

191
00:06:55,590 --> 00:06:58,260
for a given switch, including the names of the VLANs,

192
00:06:58,260 --> 00:06:59,430
the numbers for the VLANs,

193
00:06:59,430 --> 00:07:02,370
and what ports are associated with each of those VLANs.

194
00:07:02,370 --> 00:07:04,380
And finally, we have the show power command,

195
00:07:04,380 --> 00:07:06,750
which is going to be used to display the power settings,

196
00:07:06,750 --> 00:07:09,450
specifically those that support power over Ethernet,

197
00:07:09,450 --> 00:07:10,590
on a given switch,

198
00:07:10,590 --> 00:07:12,600
and we use this to manage our power distribution,

199
00:07:12,600 --> 00:07:14,040
and troubleshoot any kind of power

200
00:07:14,040 --> 00:07:15,303
over ethernet issues.

