1
00:00:00,000 --> 00:00:00,930
In this lesson,

2
00:00:00,930 --> 00:00:03,510
we're going to discuss coverage in wireless networks.

3
00:00:03,510 --> 00:00:05,010
Coverage is a measure of how large

4
00:00:05,010 --> 00:00:07,200
of an area around a wireless transmitter

5
00:00:07,200 --> 00:00:08,760
there is sufficient signal strength

6
00:00:08,760 --> 00:00:10,800
for a wireless device to utilize.

7
00:00:10,800 --> 00:00:13,260
Basically, it comes down to how much physical area

8
00:00:13,260 --> 00:00:15,360
you can use with your wireless devices

9
00:00:15,360 --> 00:00:17,250
before you get outside the coverage area

10
00:00:17,250 --> 00:00:18,600
and you lose signal.

11
00:00:18,600 --> 00:00:20,040
To determine your coverage area,

12
00:00:20,040 --> 00:00:22,440
you're going to conduct a wireless site survey.

13
00:00:22,440 --> 00:00:24,270
This will generate a heat map showing the areas

14
00:00:24,270 --> 00:00:26,070
with the highest level signals in green.

15
00:00:26,070 --> 00:00:27,330
Then as they get weaker,

16
00:00:27,330 --> 00:00:30,840
it goes to yellow, orange, and red with the weakest signals.

17
00:00:30,840 --> 00:00:32,490
Now, the signal is always going to be measured

18
00:00:32,490 --> 00:00:35,130
from your client using the RSSI,

19
00:00:35,130 --> 00:00:36,900
and this is measured in decibels.

20
00:00:36,900 --> 00:00:39,000
If you're going to measure it from your access point,

21
00:00:39,000 --> 00:00:41,070
you're going to measure it in EIRP,

22
00:00:41,070 --> 00:00:43,230
and you're going to do that in dBi.

23
00:00:43,230 --> 00:00:45,210
Now, one of the most common issues experienced

24
00:00:45,210 --> 00:00:48,480
by wifi users is insufficient wireless coverage.

25
00:00:48,480 --> 00:00:50,910
For example, let's say you have a three-story townhouse

26
00:00:50,910 --> 00:00:53,010
and you only have a single wireless access point

27
00:00:53,010 --> 00:00:54,720
on the main floor of that home.

28
00:00:54,720 --> 00:00:56,460
Well, it's going to be unlikely to provide you

29
00:00:56,460 --> 00:00:58,110
with sufficient coverage all the way up

30
00:00:58,110 --> 00:01:00,300
on the third story of your townhouse.

31
00:01:00,300 --> 00:01:01,200
In this case,

32
00:01:01,200 --> 00:01:03,180
if you're using your laptop on the first floor,

33
00:01:03,180 --> 00:01:04,890
everything's going to work just fine

34
00:01:04,890 --> 00:01:07,260
because you have really high RSSI value.

35
00:01:07,260 --> 00:01:09,060
But when you go up to the second floor,

36
00:01:09,060 --> 00:01:11,280
that RSSI value is going to lower

37
00:01:11,280 --> 00:01:13,860
because the signal got weaker as you got further away,

38
00:01:13,860 --> 00:01:14,940
and the signal has to now go

39
00:01:14,940 --> 00:01:16,530
through the ceiling of the first floor

40
00:01:16,530 --> 00:01:18,720
to get into that second floor you're sitting at.

41
00:01:18,720 --> 00:01:20,850
Now, if you go up another level to the third floor,

42
00:01:20,850 --> 00:01:22,440
that signal may be too weak

43
00:01:22,440 --> 00:01:24,870
to even register by your wireless client,

44
00:01:24,870 --> 00:01:26,880
or it can drop you completely.

45
00:01:26,880 --> 00:01:28,050
Now, if this happens,

46
00:01:28,050 --> 00:01:30,480
you're going to need to find a way to boost up that signal

47
00:01:30,480 --> 00:01:33,600
and make it stronger so you can increase your coverage area.

48
00:01:33,600 --> 00:01:36,480
To do this, you can use a signal booster to raise the power,

49
00:01:36,480 --> 00:01:38,910
you can use an antenna with a stronger dB rating,

50
00:01:38,910 --> 00:01:40,410
you can use a wireless repeater,

51
00:01:40,410 --> 00:01:42,780
or you can add a second wireless access point

52
00:01:42,780 --> 00:01:44,850
that can operate in an extended server set

53
00:01:44,850 --> 00:01:48,000
or ESS configuration with your initial access point.

54
00:01:48,000 --> 00:01:49,290
Remember, the coverage area

55
00:01:49,290 --> 00:01:51,030
for a single wireless access point

56
00:01:51,030 --> 00:01:53,130
is affected by two main factors,

57
00:01:53,130 --> 00:01:55,380
the amount of power that the transmitter is sending out,

58
00:01:55,380 --> 00:01:57,000
and the size of your antenna.

59
00:01:57,000 --> 00:01:58,680
If you replace a five-decibel antenna

60
00:01:58,680 --> 00:02:00,150
with a nine-decibel antenna,

61
00:02:00,150 --> 00:02:01,830
you're going to effectively double your range

62
00:02:01,830 --> 00:02:03,300
under the right conditions.

63
00:02:03,300 --> 00:02:05,610
As for the power being sent out, unfortunately,

64
00:02:05,610 --> 00:02:06,660
you're normally going to be limited

65
00:02:06,660 --> 00:02:08,070
in your ability to control that,

66
00:02:08,070 --> 00:02:09,780
because there's a maximum amount of power

67
00:02:09,780 --> 00:02:12,510
that the FCC and regulators allow us to use

68
00:02:12,510 --> 00:02:14,820
inside of the wireless frequency range.

69
00:02:14,820 --> 00:02:17,580
But you could use a wireless repeater.

70
00:02:17,580 --> 00:02:20,520
Now, a wireless repeater is simply a layer one device

71
00:02:20,520 --> 00:02:22,380
that has two radios built into it.

72
00:02:22,380 --> 00:02:24,120
You plug this device into a power outlet

73
00:02:24,120 --> 00:02:26,400
and you configure it to connect to your wireless network.

74
00:02:26,400 --> 00:02:28,500
Now, one of the radios grabs the signal

75
00:02:28,500 --> 00:02:29,880
from your wireless network.

76
00:02:29,880 --> 00:02:31,590
Then it's going to boost up the signal

77
00:02:31,590 --> 00:02:34,320
and send it out again off its other radio.

78
00:02:34,320 --> 00:02:35,790
This way, when the signal comes in

79
00:02:35,790 --> 00:02:37,110
on one side of the device,

80
00:02:37,110 --> 00:02:38,010
it's going to be repeated out

81
00:02:38,010 --> 00:02:40,410
at full strength on the other radio too.

82
00:02:40,410 --> 00:02:42,330
This will extend that wireless network

83
00:02:42,330 --> 00:02:44,130
into an additional area of space

84
00:02:44,130 --> 00:02:45,510
because you have this new signal

85
00:02:45,510 --> 00:02:47,640
going out from this repeater.

86
00:02:47,640 --> 00:02:49,440
For example, let's say if this repeater

87
00:02:49,440 --> 00:02:52,380
receives a signal at negative 70 RSSI.

88
00:02:52,380 --> 00:02:53,520
It can retransmit again

89
00:02:53,520 --> 00:02:56,370
on the other side at negative 30 RSSI,

90
00:02:56,370 --> 00:02:58,980
effectively making it a brand new signal.

91
00:02:58,980 --> 00:03:01,680
So in the example of the three-story townhouse,

92
00:03:01,680 --> 00:03:03,930
I might want to have my first wireless access point

93
00:03:03,930 --> 00:03:05,250
on the first floor.

94
00:03:05,250 --> 00:03:07,920
Then I could have a repeater on the second floor.

95
00:03:07,920 --> 00:03:08,910
Now, at this point,

96
00:03:08,910 --> 00:03:11,250
we'll probably have some signal on the third floor,

97
00:03:11,250 --> 00:03:12,870
or we could put another repeater

98
00:03:12,870 --> 00:03:15,540
on the third floor to boost that signal even more

99
00:03:15,540 --> 00:03:17,730
when it reaches it from the second floor.

100
00:03:17,730 --> 00:03:20,130
Finally, we could use an extended server set

101
00:03:20,130 --> 00:03:22,350
to cover the entire building properly.

102
00:03:22,350 --> 00:03:23,580
In one of my old houses,

103
00:03:23,580 --> 00:03:25,650
I actually ran ethernet twisted-pair cable

104
00:03:25,650 --> 00:03:28,080
from the basement to the second floor of my house,

105
00:03:28,080 --> 00:03:30,810
and then I connected a second wireless access point there.

106
00:03:30,810 --> 00:03:33,300
These two wireless access points worked together

107
00:03:33,300 --> 00:03:35,280
to provide coverage over the entire home,

108
00:03:35,280 --> 00:03:37,410
one from the top down from the second floor,

109
00:03:37,410 --> 00:03:39,600
and one from the bottom up going from the basement.

110
00:03:39,600 --> 00:03:41,970
And this gave me adequate coverage for the whole house.

111
00:03:41,970 --> 00:03:43,830
Now, each wireless access point operated

112
00:03:43,830 --> 00:03:44,700
on a different channel,

113
00:03:44,700 --> 00:03:46,740
and I could roam from upstairs to downstairs

114
00:03:46,740 --> 00:03:48,360
and my devices would automatically switch

115
00:03:48,360 --> 00:03:49,890
from one access point to the other

116
00:03:49,890 --> 00:03:52,140
as they needed to to maintain coverage.

117
00:03:52,140 --> 00:03:54,990
These days, we also have wireless mesh systems available,

118
00:03:54,990 --> 00:03:56,820
and they rely on a combination of repeaters

119
00:03:56,820 --> 00:03:59,340
and access points that are put into a single device,

120
00:03:59,340 --> 00:04:02,010
provide full coverage for larger homes and offices.

121
00:04:02,010 --> 00:04:04,320
Instead of having to run ethernet cables to each device,

122
00:04:04,320 --> 00:04:06,570
they instead rely on internal wireless radios

123
00:04:06,570 --> 00:04:08,790
to send the data from one device to the other

124
00:04:08,790 --> 00:04:10,560
and create a whole house mesh network

125
00:04:10,560 --> 00:04:13,060
for the wireless network with sufficient coverage.

