1
00:00:00,150 --> 00:00:01,020
In this lesson,

2
00:00:01,020 --> 00:00:03,780
we're going to discuss interference in wireless networks.

3
00:00:03,780 --> 00:00:06,300
If you remember, anytime you have multiple wireless networks

4
00:00:06,300 --> 00:00:07,830
communicating on the same channel,

5
00:00:07,830 --> 00:00:08,940
you can have interference

6
00:00:08,940 --> 00:00:11,610
because they're all talking at the same frequency.

7
00:00:11,610 --> 00:00:14,280
To avoid interference in the 2.4 gigahertz spectrum,

8
00:00:14,280 --> 00:00:18,210
we always use the three channels of one, six, and 11.

9
00:00:18,210 --> 00:00:19,470
If I'm using channel six

10
00:00:19,470 --> 00:00:21,000
and you're using channel four, though,

11
00:00:21,000 --> 00:00:22,140
we're going to have an overlap

12
00:00:22,140 --> 00:00:24,270
and we're going to interfere with each other's networks.

13
00:00:24,270 --> 00:00:26,460
This interference can lead to retransmissions

14
00:00:26,460 --> 00:00:28,710
and this will slow down both of our networks.

15
00:00:28,710 --> 00:00:30,930
So when you're conducting your site survey,

16
00:00:30,930 --> 00:00:33,030
you're always going to want to make sure you see what channels

17
00:00:33,030 --> 00:00:35,580
and frequencies are already being used in your area.

18
00:00:35,580 --> 00:00:38,010
If you create an extended service set wireless network,

19
00:00:38,010 --> 00:00:40,320
you need to plan the locations of your access points

20
00:00:40,320 --> 00:00:41,970
and the channels they're going to use.

21
00:00:41,970 --> 00:00:44,250
Remember, in a 2.4 gigahertz network,

22
00:00:44,250 --> 00:00:45,360
you always want to make sure

23
00:00:45,360 --> 00:00:47,640
you're using channels one, six, and 11,

24
00:00:47,640 --> 00:00:49,650
and you never want two of the same channel number

25
00:00:49,650 --> 00:00:51,900
sitting next to each other and overlapping.

26
00:00:51,900 --> 00:00:54,810
This way, I can make sure that I have good coverage.

27
00:00:54,810 --> 00:00:57,120
For example, let's say I was installing access points

28
00:00:57,120 --> 00:00:58,320
down a long hallway.

29
00:00:58,320 --> 00:01:02,940
I would install them as 1, 6, 11, 1, 6, and 11.

30
00:01:02,940 --> 00:01:05,730
Notice that I skipped each one to a different number.

31
00:01:05,730 --> 00:01:07,710
This ensures there's no overlapping zones.

32
00:01:07,710 --> 00:01:10,500
They're touching one another of the same type of number.

33
00:01:10,500 --> 00:01:13,650
Also, you want to ensure you have 10 to 15% overlap

34
00:01:13,650 --> 00:01:15,240
between the two access points

35
00:01:15,240 --> 00:01:16,800
to make sure you have sufficient coverage

36
00:01:16,800 --> 00:01:18,990
and time for the devices to hand off.

37
00:01:18,990 --> 00:01:21,390
Now, if you're using a newer 5 gigahertz network,

38
00:01:21,390 --> 00:01:23,190
you're going to utilize a honeycomb pattern

39
00:01:23,190 --> 00:01:25,440
for your access points as they're being installed,

40
00:01:25,440 --> 00:01:27,270
and you should always ensure that each channel

41
00:01:27,270 --> 00:01:30,090
is not repeated until you're at least two zones away.

42
00:01:30,090 --> 00:01:31,470
This will ensure adequate coverage

43
00:01:31,470 --> 00:01:33,090
and minimize interference.

44
00:01:33,090 --> 00:01:35,310
Next, let's cover attenuation.

45
00:01:35,310 --> 00:01:37,470
Attenuation is a reduction of signal strength

46
00:01:37,470 --> 00:01:40,290
between the transmission and receipt of the wireless signal.

47
00:01:40,290 --> 00:01:42,960
Attenuation can occur for lots of different reasons,

48
00:01:42,960 --> 00:01:44,820
such as increasing the distance between the transmitter

49
00:01:44,820 --> 00:01:47,790
and the receiver, hitting a wall or other physical obstacle

50
00:01:47,790 --> 00:01:49,260
or signal interference

51
00:01:49,260 --> 00:01:51,060
that's reducing the overall signal strength

52
00:01:51,060 --> 00:01:52,050
because of more noise

53
00:01:52,050 --> 00:01:53,910
in the environment causing interference.

54
00:01:53,910 --> 00:01:56,610
Attenuation can occur within the antenna's cable itself

55
00:01:56,610 --> 00:01:58,410
or in the radio frequency wave

56
00:01:58,410 --> 00:02:00,060
as it's traveling away from the transmitter

57
00:02:00,060 --> 00:02:01,530
and towards the receiver.

58
00:02:01,530 --> 00:02:02,970
When the attenuation is occurring

59
00:02:02,970 --> 00:02:04,380
inside the antenna's cable,

60
00:02:04,380 --> 00:02:06,180
it's normally going to be caused by the materials

61
00:02:06,180 --> 00:02:08,130
and the construction of that antenna.

62
00:02:08,130 --> 00:02:10,680
If low quality components were used to make that antenna

63
00:02:10,680 --> 00:02:12,180
or the cables inside of it,

64
00:02:12,180 --> 00:02:14,850
there are going to be more resistance inside that wire

65
00:02:14,850 --> 00:02:16,920
and that leads to more attenuation.

66
00:02:16,920 --> 00:02:18,150
To increase the signal strength

67
00:02:18,150 --> 00:02:19,560
and reduce the attenuation,

68
00:02:19,560 --> 00:02:20,760
you can replace the cable

69
00:02:20,760 --> 00:02:22,680
or the antenna with a higher quality,

70
00:02:22,680 --> 00:02:24,450
lower-resistant component.

71
00:02:24,450 --> 00:02:26,820
With radio frequency wave signal attenuation,

72
00:02:26,820 --> 00:02:29,850
one of the causes of this is multi-path reception.

73
00:02:29,850 --> 00:02:31,770
Now, this occurs when the transmitted signal

74
00:02:31,770 --> 00:02:34,470
starts bouncing off walls and other physical objects,

75
00:02:34,470 --> 00:02:37,680
and then it eventually gets redirected back to the receiver.

76
00:02:37,680 --> 00:02:39,270
Now, for example, let's say I was standing

77
00:02:39,270 --> 00:02:40,770
on one side of the room and you're standing

78
00:02:40,770 --> 00:02:42,000
on the other side of the room

79
00:02:42,000 --> 00:02:43,200
and there's a big support column

80
00:02:43,200 --> 00:02:44,700
standing right between us.

81
00:02:44,700 --> 00:02:45,990
If I wanted to send a ball to you

82
00:02:45,990 --> 00:02:47,910
that's going to signify my radio waves,

83
00:02:47,910 --> 00:02:49,620
I couldn't throw it directly to you

84
00:02:49,620 --> 00:02:51,510
because if I did that, it's going to hit the column

85
00:02:51,510 --> 00:02:53,100
and bounce back towards me.

86
00:02:53,100 --> 00:02:56,460
So instead, I would need an omnidirectional antenna

87
00:02:56,460 --> 00:02:58,860
to throw out a lot of different balls simultaneously.

88
00:02:58,860 --> 00:03:00,420
Some those will bounce off the sidewalls

89
00:03:00,420 --> 00:03:01,680
and they'll eventually reach you.

90
00:03:01,680 --> 00:03:04,350
Some will hit the pole in front of me and bounce back to me.

91
00:03:04,350 --> 00:03:06,390
But because of all this different balance,

92
00:03:06,390 --> 00:03:07,410
we're going to have slower

93
00:03:07,410 --> 00:03:09,840
and weaker signals by the time they get to you

94
00:03:09,840 --> 00:03:12,180
because I had to bounce off the wall first, right?

95
00:03:12,180 --> 00:03:14,910
Well, the same thing happens with our radio frequency waves.

96
00:03:14,910 --> 00:03:16,230
They may bounce around the room

97
00:03:16,230 --> 00:03:17,430
and they'll eventually get to you,

98
00:03:17,430 --> 00:03:20,370
but they may be attenuated and weaker than before.

99
00:03:20,370 --> 00:03:23,220
And it's going to lead to a lower RSSI value for you

100
00:03:23,220 --> 00:03:25,110
and lower throughput for the data being sent

101
00:03:25,110 --> 00:03:26,133
over these networks.

