1
00:00:00,000 --> 00:00:01,680
In this video, we're going to discuss

2
00:00:01,680 --> 00:00:04,140
wireless considerations that you need to think about

3
00:00:04,140 --> 00:00:06,780
as you start to troubleshoot your wireless networks.

4
00:00:06,780 --> 00:00:09,450
We're going to begin by discussing antennas, their placement,

5
00:00:09,450 --> 00:00:11,430
their type, and their polarization.

6
00:00:11,430 --> 00:00:14,460
Then we're going to cover channel utilization, site surveys,

7
00:00:14,460 --> 00:00:16,050
and the types of information that those things

8
00:00:16,050 --> 00:00:18,660
can help us with as we troubleshoot our networks.

9
00:00:18,660 --> 00:00:20,970
Finally, we're going to talk about wireless access points,

10
00:00:20,970 --> 00:00:25,110
or AP association times, and how association actually works.

11
00:00:25,110 --> 00:00:27,510
First, let's talk all about antennas.

12
00:00:27,510 --> 00:00:29,610
Antennas can come in multiple different types,

13
00:00:29,610 --> 00:00:31,740
and each one has its own purpose.

14
00:00:31,740 --> 00:00:33,870
By default, most wireless access points

15
00:00:33,870 --> 00:00:35,850
are going to use omnidirectional antennas,

16
00:00:35,850 --> 00:00:37,320
and normally they're going to be located

17
00:00:37,320 --> 00:00:39,120
in a vertical form factor.

18
00:00:39,120 --> 00:00:41,760
Now for a vertical antenna, the radiation pattern

19
00:00:41,760 --> 00:00:44,220
for the radio frequency waves is going to extend outward

20
00:00:44,220 --> 00:00:46,320
in all directions away from that antenna

21
00:00:46,320 --> 00:00:48,210
and away from the wireless access point

22
00:00:48,210 --> 00:00:50,010
at an equal power level.

23
00:00:50,010 --> 00:00:51,540
As the radio waves travel further

24
00:00:51,540 --> 00:00:52,860
and further from that antenna,

25
00:00:52,860 --> 00:00:54,840
the signal is going to get lost a little bit

26
00:00:54,840 --> 00:00:57,330
and the power and strength is going to decrease.

27
00:00:57,330 --> 00:00:59,400
Now, if you're monitoring this from your client,

28
00:00:59,400 --> 00:01:00,540
you're going to see that you have

29
00:01:00,540 --> 00:01:03,330
more negative RSSIs as you go further

30
00:01:03,330 --> 00:01:06,000
from the wireless access point and its antenna.

31
00:01:06,000 --> 00:01:07,680
Now, for example, let's say you're sitting

32
00:01:07,680 --> 00:01:09,090
right next to the antenna.

33
00:01:09,090 --> 00:01:12,840
You might have an RSSI of -30 to -40 decibels,

34
00:01:12,840 --> 00:01:14,605
but if you move out a hundred feet away,

35
00:01:14,605 --> 00:01:17,580
that signal strength may now be at an RSSI

36
00:01:17,580 --> 00:01:20,790
of -65 or -70 decibels.

37
00:01:20,790 --> 00:01:22,365
Another type of antenna you might come across

38
00:01:22,365 --> 00:01:26,280
is known as a dipole antenna, or a bi-directional antenna.

39
00:01:26,280 --> 00:01:28,020
With a dipole antenna, the antenna

40
00:01:28,020 --> 00:01:29,880
is going to produce a radio frequency wave

41
00:01:29,880 --> 00:01:31,590
that extends outward in two directions

42
00:01:31,590 --> 00:01:33,180
away from the antenna.

43
00:01:33,180 --> 00:01:35,190
With a dipole antenna, you're normally going to see

44
00:01:35,190 --> 00:01:37,260
a higher RSSI on the client device,

45
00:01:37,260 --> 00:01:39,600
even when it's located further from the access point.

46
00:01:39,600 --> 00:01:42,030
Because this antenna can now focus its power

47
00:01:42,030 --> 00:01:45,443
in only two directions instead of the entire 360 degrees

48
00:01:45,443 --> 00:01:49,170
around itself like an omnidirectional antenna produces.

49
00:01:49,170 --> 00:01:51,120
So if you need the radio frequency waves

50
00:01:51,120 --> 00:01:52,560
to only go in two directions,

51
00:01:52,560 --> 00:01:54,810
a dipole is going to be a good option for you,

52
00:01:54,810 --> 00:01:56,250
but they're not heavily used

53
00:01:56,250 --> 00:01:58,950
in wireless networks for the most part.

54
00:01:58,950 --> 00:02:01,950
Next, we have this thing known as a Yagi antenna.

55
00:02:01,950 --> 00:02:04,243
Now, a Yagi antenna is a type of unidirectional antenna

56
00:02:04,243 --> 00:02:07,920
that sends the radio frequency waves only in one direction.

57
00:02:07,920 --> 00:02:09,780
Due to this focusing of the radio frequency

58
00:02:09,780 --> 00:02:12,030
in a singular direction, a Yagi antenna

59
00:02:12,030 --> 00:02:13,350
can send the radio frequency waves

60
00:02:13,350 --> 00:02:16,020
further in a single direction, using less power

61
00:02:16,020 --> 00:02:18,030
than an omnidirectional antenna will.

62
00:02:18,030 --> 00:02:20,370
Normally, you're going to see a Yagi antenna used

63
00:02:20,370 --> 00:02:21,930
when you're trying to connect two different sites

64
00:02:21,930 --> 00:02:23,490
using a wireless link.

65
00:02:23,490 --> 00:02:25,714
For example, you may want to connect two office buildings

66
00:02:25,714 --> 00:02:28,080
on a college campus using a wireless link

67
00:02:28,080 --> 00:02:30,510
instead of running a buried fiber optic cable.

68
00:02:30,510 --> 00:02:33,990
In this case, you're going to use a Yagi antenna to do that.

69
00:02:33,990 --> 00:02:36,990
Finally, we have a parabolic grid, or disc antenna.

70
00:02:36,990 --> 00:02:39,330
These antennas are unidirectional antennas

71
00:02:39,330 --> 00:02:40,860
just like a Yagi antenna is,

72
00:02:40,860 --> 00:02:42,900
but they're built a little bit differently.

73
00:02:42,900 --> 00:02:45,600
Now, parabolic grid antennas are most commonly used

74
00:02:45,600 --> 00:02:47,910
for site to site applications, where you need to connect

75
00:02:47,910 --> 00:02:49,350
buildings over a longer distance

76
00:02:49,350 --> 00:02:51,180
than you would with a Yagi antenna.

77
00:02:51,180 --> 00:02:53,760
Like a Yagi antenna, a parabolic antenna is going to allow

78
00:02:53,760 --> 00:02:56,490
the radio wave to be transmitted in only one direction,

79
00:02:56,490 --> 00:02:58,770
making it a unidirectional antenna.

80
00:02:58,770 --> 00:03:00,183
Now, when it comes to placing your antennas,

81
00:03:00,183 --> 00:03:03,150
this is going to be dependent on where you're going to place them,

82
00:03:03,150 --> 00:03:04,920
inside or outside of your building,

83
00:03:04,920 --> 00:03:07,110
to create the coverage that you desire.

84
00:03:07,110 --> 00:03:08,670
If you're setting up a site to site

85
00:03:08,670 --> 00:03:10,290
or building to building connection,

86
00:03:10,290 --> 00:03:12,330
you're going to want to use a unidirectional antenna,

87
00:03:12,330 --> 00:03:14,610
like a parabolic or a Yagi antenna.

88
00:03:14,610 --> 00:03:16,110
Now you're going to take that and mount it

89
00:03:16,110 --> 00:03:17,580
on the outside of your building,

90
00:03:17,580 --> 00:03:19,710
and usually you're going to attach it to the roof

91
00:03:19,710 --> 00:03:21,210
and make sure there's a clear line of sight

92
00:03:21,210 --> 00:03:24,060
between both antennas on each of those buildings.

93
00:03:24,060 --> 00:03:25,980
Now, one of the common issues you're going to experience

94
00:03:25,980 --> 00:03:27,870
with wireless antennas for a site to site

95
00:03:27,870 --> 00:03:29,370
or building to building connection

96
00:03:29,370 --> 00:03:31,860
is that the connection may deteriorate and slow down

97
00:03:31,860 --> 00:03:34,350
or completely stop over time.

98
00:03:34,350 --> 00:03:36,810
If this occurs, you need to ensure that both antennas

99
00:03:36,810 --> 00:03:38,760
still have a clear sight between them.

100
00:03:38,760 --> 00:03:40,742
For example, maybe you have two office buildings

101
00:03:40,742 --> 00:03:43,080
and they're only one or two stories high.

102
00:03:43,080 --> 00:03:45,390
You've gone ahead and installed the antennas in the fall,

103
00:03:45,390 --> 00:03:46,800
and there was no issues at all.

104
00:03:46,800 --> 00:03:48,870
You had a perfectly clear line of sight.

105
00:03:48,870 --> 00:03:50,670
But it's been about six months

106
00:03:50,670 --> 00:03:53,280
and now the seasons have changed and spring appears,

107
00:03:53,280 --> 00:03:55,530
and your wireless connection may start to be affected

108
00:03:55,530 --> 00:03:57,630
by trees because they've sprouted new leaves,

109
00:03:57,630 --> 00:03:59,550
and they are now blocking your line of sight clearly

110
00:03:59,550 --> 00:04:01,350
between those two buildings.

111
00:04:01,350 --> 00:04:04,050
Similarly, if in the wintertime there's a lot of snow,

112
00:04:04,050 --> 00:04:05,640
this can also block your signal.

113
00:04:05,640 --> 00:04:07,680
Or if it rains heavily in the summer,

114
00:04:07,680 --> 00:04:09,360
you could also have a deteriorating signal

115
00:04:09,360 --> 00:04:10,950
because the water droplets will block

116
00:04:10,950 --> 00:04:14,040
the wireless communication between these two antennas.

117
00:04:14,040 --> 00:04:15,840
So if you're working with antennas,

118
00:04:15,840 --> 00:04:17,100
you need to think about these things

119
00:04:17,100 --> 00:04:18,660
when you're working outside.

120
00:04:18,660 --> 00:04:19,493
Now, on the other hand,

121
00:04:19,493 --> 00:04:21,209
if you're working inside your building,

122
00:04:21,209 --> 00:04:23,190
you're going to be more likely to use omnidirectional

123
00:04:23,190 --> 00:04:25,020
or unidirectional patch antennas

124
00:04:25,020 --> 00:04:26,580
to control the signal being radiated

125
00:04:26,580 --> 00:04:29,250
by your wireless networks to each of your clients.

126
00:04:29,250 --> 00:04:30,690
With omnidirectional antennas,

127
00:04:30,690 --> 00:04:32,460
it's going to be common to place this on the ceiling

128
00:04:32,460 --> 00:04:34,650
in the middle of the office or classroom.

129
00:04:34,650 --> 00:04:36,450
For a unidirectional patch antenna,

130
00:04:36,450 --> 00:04:38,220
you're usually going to place this on an outer wall

131
00:04:38,220 --> 00:04:39,990
of the building facing inward,

132
00:04:39,990 --> 00:04:42,360
thereby directing all those radio frequency waves

133
00:04:42,360 --> 00:04:45,360
back inward towards the office or the classrooms.

134
00:04:45,360 --> 00:04:47,370
Now, the last thing we need to discuss with antennas

135
00:04:47,370 --> 00:04:49,560
is the concept of polarization.

136
00:04:49,560 --> 00:04:52,170
Polarization is the orientation of the electric field

137
00:04:52,170 --> 00:04:54,930
or transmissions that are occurring from that antenna.

138
00:04:54,930 --> 00:04:57,990
Basically, as the radio frequency waves leave the antenna,

139
00:04:57,990 --> 00:04:59,790
how is it going to be oriented?

140
00:04:59,790 --> 00:05:02,430
Every antenna has a polarization associated with it,

141
00:05:02,430 --> 00:05:03,720
and for Wi-Fi networks,

142
00:05:03,720 --> 00:05:05,850
our antennas usually are going to have a vertical

143
00:05:05,850 --> 00:05:08,820
or horizontal polarization associated with them.

144
00:05:08,820 --> 00:05:11,490
Now, most Wi-Fi clients that have external antennas

145
00:05:11,490 --> 00:05:13,620
are going to use vertical polarization,

146
00:05:13,620 --> 00:05:15,875
but your wireless access point could use vertical

147
00:05:15,875 --> 00:05:18,150
or horizontal polarization,

148
00:05:18,150 --> 00:05:20,340
depending on what type of antenna it has.

149
00:05:20,340 --> 00:05:22,080
Now, if you see a problem with some clients

150
00:05:22,080 --> 00:05:24,690
getting a poor RSSI, even though they're pretty close

151
00:05:24,690 --> 00:05:26,700
to your access point, this may indicate

152
00:05:26,700 --> 00:05:28,440
you have a polarization issue.

153
00:05:28,440 --> 00:05:30,510
If this is the case, I want you to try flipping

154
00:05:30,510 --> 00:05:32,190
the wireless access point antenna

155
00:05:32,190 --> 00:05:34,350
to allow the clients to better connect to that device

156
00:05:34,350 --> 00:05:36,690
if they support bending the antenna upwards.

157
00:05:36,690 --> 00:05:38,253
Or if you're using wireless access points

158
00:05:38,253 --> 00:05:39,960
that are sitting on the floor,

159
00:05:39,960 --> 00:05:42,330
you want to make sure you're using vertical polarization

160
00:05:42,330 --> 00:05:45,030
and radiating antennas to increase your coverage area.

161
00:05:45,030 --> 00:05:46,350
If you're using horizontal,

162
00:05:46,350 --> 00:05:48,780
it's going to keep sending those radio waves out horizontally,

163
00:05:48,780 --> 00:05:51,120
right along the floor, and add up to the desk level

164
00:05:51,120 --> 00:05:52,560
where everybody else is working.

165
00:05:52,560 --> 00:05:55,920
Remember, most Wi-Fi networks use vertical polarization,

166
00:05:55,920 --> 00:05:57,600
so your antennas should be sticking upward

167
00:05:57,600 --> 00:05:59,460
if you're using an omnidirectional antenna

168
00:05:59,460 --> 00:06:01,260
with your Wi-Fi networks.

169
00:06:01,260 --> 00:06:03,840
All right, next we have channel utilization.

170
00:06:03,840 --> 00:06:05,307
Channel utilization is a statistic

171
00:06:05,307 --> 00:06:07,830
or measure of the amount of airtime utilization

172
00:06:07,830 --> 00:06:09,850
that occurs for a particular frequency or channel.

173
00:06:09,850 --> 00:06:12,270
If there's a higher rate of channel utilization,

174
00:06:12,270 --> 00:06:13,500
then that means there's more traffic

175
00:06:13,500 --> 00:06:16,080
being transmitted over that particular frequency.

176
00:06:16,080 --> 00:06:18,030
In order to have a fast wireless network,

177
00:06:18,030 --> 00:06:21,600
you want to keep your channel utilization under around 30%.

178
00:06:21,600 --> 00:06:23,580
Now, channel utilization is not something

179
00:06:23,580 --> 00:06:24,960
you alone can control though,

180
00:06:24,960 --> 00:06:26,580
because there's lots of these different channels

181
00:06:26,580 --> 00:06:29,220
that overlap with other people in that area,

182
00:06:29,220 --> 00:06:30,780
and so these same channels and frequencies

183
00:06:30,780 --> 00:06:33,900
can be used by your network and other networks too.

184
00:06:33,900 --> 00:06:36,150
For example, let's say you're running a wireless B,

185
00:06:36,150 --> 00:06:38,340
or a wireless G, or a wireless N network,

186
00:06:38,340 --> 00:06:41,130
and you're operating in the 2.4 gigahertz spectrum.

187
00:06:41,130 --> 00:06:42,540
We are going to be using the same channels

188
00:06:42,540 --> 00:06:45,750
that everybody else is, channels one, six and 11.

189
00:06:45,750 --> 00:06:47,520
Now, if you have a large office building,

190
00:06:47,520 --> 00:06:48,615
this won't be a big problem for you

191
00:06:48,615 --> 00:06:50,100
because nobody else is going to be

192
00:06:50,100 --> 00:06:52,110
in the same general area as we are.

193
00:06:52,110 --> 00:06:54,000
But if you're in a crowded office building

194
00:06:54,000 --> 00:06:56,370
or a shopping mall or an apartment building,

195
00:06:56,370 --> 00:06:58,080
this can easily start to have a lot

196
00:06:58,080 --> 00:06:59,130
of different wireless networks

197
00:06:59,130 --> 00:07:02,340
operating on the same channels as ours in the same location.

198
00:07:02,340 --> 00:07:03,717
Now, when wireless access points

199
00:07:03,717 --> 00:07:06,180
and wireless clients are operating on the same channel

200
00:07:06,180 --> 00:07:08,670
and all of those things are in the same range of each other,

201
00:07:08,670 --> 00:07:11,250
they're going to begin to form a single broadcast domain,

202
00:07:11,250 --> 00:07:13,110
similar to an ethernet hub.

203
00:07:13,110 --> 00:07:15,360
All of the devices can hear each other's transmissions,

204
00:07:15,360 --> 00:07:17,760
and if any two devices transmit at the same time,

205
00:07:17,760 --> 00:07:20,760
their radio signals will collide and it becomes garbled,

206
00:07:20,760 --> 00:07:24,060
which results in data corruption or a complete frame loss.

207
00:07:24,060 --> 00:07:25,830
If there's an excessive amount of collisions,

208
00:07:25,830 --> 00:07:27,615
data will never be remitted successfully

209
00:07:27,615 --> 00:07:31,170
and the wireless network could become unusable.

210
00:07:31,170 --> 00:07:34,620
So to avoid collisions, 802.11 wireless devices

211
00:07:34,620 --> 00:07:36,540
use a "listen before they speak" approach

212
00:07:36,540 --> 00:07:38,460
when they're accessing the wireless medium,

213
00:07:38,460 --> 00:07:39,900
which is the radio frequency,

214
00:07:39,900 --> 00:07:44,160
following the CSMA/CA, or collision avoidance techniques.

215
00:07:44,160 --> 00:07:45,990
Now with this, devices are going to perform

216
00:07:45,990 --> 00:07:49,560
a Clear Channel Assessment, or CCA, by first listening

217
00:07:49,560 --> 00:07:51,900
to see if another device is actively transmitting

218
00:07:51,900 --> 00:07:54,360
on the channel before they attempt to send their own frames

219
00:07:54,360 --> 00:07:56,040
on that given frequency.

220
00:07:56,040 --> 00:07:58,149
Now, when a device detects another transmission in progress,

221
00:07:58,149 --> 00:08:00,480
it's going to perform a random back off

222
00:08:00,480 --> 00:08:01,950
for a short period of time,

223
00:08:01,950 --> 00:08:04,860
after which it's going to perform another CCA check

224
00:08:04,860 --> 00:08:06,690
before it attempts to transmit.

225
00:08:06,690 --> 00:08:08,520
If the channel is clear after the check,

226
00:08:08,520 --> 00:08:10,380
that device will be able to access the channel

227
00:08:10,380 --> 00:08:11,760
and send some data.

228
00:08:11,760 --> 00:08:13,908
Now, as the number of devices need to transmit frames

229
00:08:13,908 --> 00:08:16,050
starts increasing on a channel,

230
00:08:16,050 --> 00:08:18,030
this is going to cause congestion to occur

231
00:08:18,030 --> 00:08:20,340
to the point where devices can spend a lot more time

232
00:08:20,340 --> 00:08:22,650
waiting to be able to send something.

233
00:08:22,650 --> 00:08:24,060
This results in slower speeds

234
00:08:24,060 --> 00:08:25,560
because devices have to wait longer

235
00:08:25,560 --> 00:08:27,180
before they can send their data.

236
00:08:27,180 --> 00:08:28,500
This is the negative effect

237
00:08:28,500 --> 00:08:30,390
of having high channel utilization,

238
00:08:30,390 --> 00:08:33,450
and at least a slower throughput for our network devices.

239
00:08:33,450 --> 00:08:35,010
Now, how do we solve this problem

240
00:08:35,010 --> 00:08:36,929
of over channel utilization?

241
00:08:36,929 --> 00:08:40,200
Well, first we're going to start by conducting a site survey.

242
00:08:40,200 --> 00:08:42,650
Now, a site survey, also known as a wireless survey,

243
00:08:42,650 --> 00:08:43,860
is the process of planning

244
00:08:43,860 --> 00:08:45,450
and designing a wireless network

245
00:08:45,450 --> 00:08:46,620
to provide a wireless solution

246
00:08:46,620 --> 00:08:48,570
that will deliver the required wireless coverage,

247
00:08:48,570 --> 00:08:51,450
the data rates, network capacity, roaming capability,

248
00:08:51,450 --> 00:08:54,630
and quality of service that your organization desires.

249
00:08:54,630 --> 00:08:57,300
As part of the wireless survey, you need to determine

250
00:08:57,300 --> 00:08:59,100
where each access point is located,

251
00:08:59,100 --> 00:09:01,440
what power level it's using to transmit

252
00:09:01,440 --> 00:09:05,520
by using its effective isotropic radiated power, or EIRP,

253
00:09:05,520 --> 00:09:08,337
overlapping coverage areas for your wireless access points,

254
00:09:08,337 --> 00:09:10,620
and the other wireless access points in clients

255
00:09:10,620 --> 00:09:12,120
that may be operating in the same,

256
00:09:12,120 --> 00:09:14,430
or general area or channels is you.

257
00:09:14,430 --> 00:09:16,680
Now, by using this site survey information,

258
00:09:16,680 --> 00:09:17,790
you can determine if you need

259
00:09:17,790 --> 00:09:20,310
to change the channels you're using to a less busy,

260
00:09:20,310 --> 00:09:21,690
less utilized channel,

261
00:09:21,690 --> 00:09:23,790
or if you may need to upgrade your networks

262
00:09:23,790 --> 00:09:25,980
to a new frequency band altogether.

263
00:09:25,980 --> 00:09:27,750
After all, if you decide to upgrade

264
00:09:27,750 --> 00:09:31,200
to a wireless N, wireless AC, or wireless AX network,

265
00:09:31,200 --> 00:09:33,480
and you start using the five gigahertz spectrum,

266
00:09:33,480 --> 00:09:35,940
this gives you 24 non-overlapping channels

267
00:09:35,940 --> 00:09:38,820
instead of the three in the 2.4 gigahertz spectrum.

268
00:09:38,820 --> 00:09:41,430
So there's going to be a lot less overall utilization

269
00:09:41,430 --> 00:09:44,940
on each of those 24 channels in the five gigahertz spectrum.

270
00:09:44,940 --> 00:09:47,430
By conducting a site survey, you can better understand

271
00:09:47,430 --> 00:09:49,980
the wireless environment in and around your networks,

272
00:09:49,980 --> 00:09:52,080
and this is going to allow you to configure your devices

273
00:09:52,080 --> 00:09:53,790
to use the less utilized channels,

274
00:09:53,790 --> 00:09:55,980
ensure there's proper coverage for all of your work areas,

275
00:09:55,980 --> 00:09:57,990
and ensure your wireless network

276
00:09:57,990 --> 00:09:59,880
is not being blocked or interfered with

277
00:09:59,880 --> 00:10:02,550
by physical obstacles within the building.

278
00:10:02,550 --> 00:10:03,660
Finally, we need to talk

279
00:10:03,660 --> 00:10:06,330
about wireless access point association times.

280
00:10:06,330 --> 00:10:08,250
Now, when a wireless client attempts to connect

281
00:10:08,250 --> 00:10:11,970
to a wireless network, it goes through a seven step process.

282
00:10:11,970 --> 00:10:14,148
First, the wireless client is going to send a probe request

283
00:10:14,148 --> 00:10:16,933
to discover any 802.11 wireless networks

284
00:10:16,933 --> 00:10:19,530
in the general location that it's in.

285
00:10:19,530 --> 00:10:21,900
Essentially, it's going to send a broadcast message

286
00:10:21,900 --> 00:10:26,900
to the BSSID of ff:ff:ff:ff:ff:ff,

287
00:10:27,720 --> 00:10:29,670
and all the access points in that area

288
00:10:29,670 --> 00:10:32,520
that are using the same frequency, either 2.4 gigahertz

289
00:10:32,520 --> 00:10:35,400
or five gigahertz, will respond to that client.

290
00:10:35,400 --> 00:10:38,040
Second, any access points that receive this probe,

291
00:10:38,040 --> 00:10:40,230
will check to see if they can support the data rate

292
00:10:40,230 --> 00:10:42,690
that the client is now requesting in that probe.

293
00:10:42,690 --> 00:10:45,450
For example, if I'm a wireless AC access point

294
00:10:45,450 --> 00:10:47,940
and you just requested to communicate using wireless B,

295
00:10:47,940 --> 00:10:49,320
I'm going to ignore your request

296
00:10:49,320 --> 00:10:51,120
because I'm operating at five gigahertz

297
00:10:51,120 --> 00:10:53,520
and you're operating at 2.4 gigahertz.

298
00:10:53,520 --> 00:10:55,962
But if we both support wireless N, then I can respond

299
00:10:55,962 --> 00:10:59,310
with a probe response that provides my SSID,

300
00:10:59,310 --> 00:11:01,770
my supported data rates, my encryption types

301
00:11:01,770 --> 00:11:03,300
if I'm using wireless security,

302
00:11:03,300 --> 00:11:06,390
and other capabilities of my particular access point.

303
00:11:06,390 --> 00:11:08,520
Third, our wireless client will then send

304
00:11:08,520 --> 00:11:11,891
a low level 802.11 authentication frame to the access point,

305
00:11:11,891 --> 00:11:14,430
and this will begin the authentication handshake

306
00:11:14,430 --> 00:11:17,040
between my client and the access point.

307
00:11:17,040 --> 00:11:19,850
Fourth, the access point receives this authentication frame

308
00:11:19,850 --> 00:11:21,540
and responds with an acknowledgement

309
00:11:21,540 --> 00:11:23,190
to continue the handshake.

310
00:11:23,190 --> 00:11:24,870
If the wireless access point receives

311
00:11:24,870 --> 00:11:26,670
anything other than an authentication

312
00:11:26,670 --> 00:11:28,770
or a probe request from this client though,

313
00:11:28,770 --> 00:11:30,990
it's going to send a deauthentication frame

314
00:11:30,990 --> 00:11:33,060
and break the communication with this client,

315
00:11:33,060 --> 00:11:34,890
because this client is not yet part

316
00:11:34,890 --> 00:11:36,840
of my authenticated network.

317
00:11:36,840 --> 00:11:38,850
Fifth, the wireless client is going to choose

318
00:11:38,850 --> 00:11:40,920
the access point it wants to associate with

319
00:11:40,920 --> 00:11:42,630
and sends an association request

320
00:11:42,630 --> 00:11:45,390
using the encryption and 802.11 capabilities

321
00:11:45,390 --> 00:11:47,730
that are supported by that access point.

322
00:11:47,730 --> 00:11:49,920
Sixth, the access point is going to process

323
00:11:49,920 --> 00:11:52,110
the association request if the information

324
00:11:52,110 --> 00:11:54,090
sent matches its own capabilities,

325
00:11:54,090 --> 00:11:56,730
and then an association ID is being created

326
00:11:56,730 --> 00:11:59,370
for this wireless client and this access point.

327
00:11:59,370 --> 00:12:00,930
And the access point is going to respond

328
00:12:00,930 --> 00:12:03,570
with an association response of success.

329
00:12:03,570 --> 00:12:06,030
This way, the client knows it is now fully connected

330
00:12:06,030 --> 00:12:07,890
to this wireless access point

331
00:12:07,890 --> 00:12:09,450
Seven, now that the client

332
00:12:09,450 --> 00:12:11,370
is fully connected and associated,

333
00:12:11,370 --> 00:12:13,620
it can begin to conduct any data transfer it needs to

334
00:12:13,620 --> 00:12:16,920
and utilize the wireless network and its associated devices.

335
00:12:16,920 --> 00:12:19,320
Now, that's how everything is supposed to operate,

336
00:12:19,320 --> 00:12:21,720
but sometimes you're going to see a wireless network

337
00:12:21,720 --> 00:12:23,640
that has a really long association time

338
00:12:23,640 --> 00:12:25,260
for an end user's client.

339
00:12:25,260 --> 00:12:27,720
This is because the client has to scan the airwaves,

340
00:12:27,720 --> 00:12:29,880
find the access points it might want to connect to,

341
00:12:29,880 --> 00:12:32,910
request the association, authenticate to the access point,

342
00:12:32,910 --> 00:12:36,060
and then contact the DHCP server to get an IP address

343
00:12:36,060 --> 00:12:37,500
prior to being able to actually use

344
00:12:37,500 --> 00:12:40,290
that wireless network connection that we just established.

345
00:12:40,290 --> 00:12:42,150
This process can take just a few seconds

346
00:12:42,150 --> 00:12:43,860
in a not heavily loaded network,

347
00:12:43,860 --> 00:12:45,870
but it can take up to 30 to 60 seconds

348
00:12:45,870 --> 00:12:47,370
if you have a busier network.

349
00:12:47,370 --> 00:12:49,230
To speed up the association process,

350
00:12:49,230 --> 00:12:51,900
clients should be located in a high signal strength area.

351
00:12:51,900 --> 00:12:54,599
Those with the highest RSSIs during the association process

352
00:12:54,599 --> 00:12:56,820
are going to give us a stronger strength,

353
00:12:56,820 --> 00:12:58,140
and that's going to drastically reduce

354
00:12:58,140 --> 00:13:00,093
the wait time during this association.

