WEBVTT - This file was automatically generated by VIMEO

0
00:00:08.100 --> 00:00:11.200
Hello everyone. Welcome to the video number 3.2. And in

1
00:00:11.200 --> 00:00:14.400
 this video we're going to assemble the hardware for

2
00:00:14.400 --> 00:00:18.400
 the Smart Lock that we will control with

3
00:00:17.400 --> 00:00:20.100
 the Bluetooth. So guys,

4
00:00:20.100 --> 00:00:23.500
 let's get started with that in the first video. We're going to assemble the

5
00:00:23.500 --> 00:00:27.100
 hardware and in the next video, we're going to code the

6
00:00:26.100 --> 00:00:29.600
 board to control the lock using

7
00:00:29.600 --> 00:00:32.400
 the Bluetooth and in the third video we're going

8
00:00:32.400 --> 00:00:35.700
 to do while at the mobile app using MIT

9
00:00:35.700 --> 00:00:38.300
 app and winter to make a

10
00:00:38.300 --> 00:00:42.100
 custom app and install in your mobile phone and control the

11
00:00:41.100 --> 00:00:43.900
 lock. So guys, let's get started with that.

12
00:00:45.400 --> 00:00:48.300
Okay, and we need to connect the

13
00:00:48.300 --> 00:00:48.700
 pins.

14
00:00:49.700 --> 00:00:51.200
with the esp32

15
00:00:52.100 --> 00:00:55.800
So we need three pins 3 volt ground and the D2

16
00:00:55.800 --> 00:00:58.800
 and I'm going to use the red pin with the

17
00:00:58.800 --> 00:01:00.500
 three volt.

18
00:01:01.100 --> 00:01:04.600
To control the relay and brown with

19
00:01:04.600 --> 00:01:05.100
 the ground.

20
00:01:08.500 --> 00:01:10.600
and that orange with the

21
00:01:11.900 --> 00:01:14.700
D2 for the signal, okay.

22
00:01:16.200 --> 00:01:19.400
So you guys can get the idea 3 volt ground and

23
00:01:19.400 --> 00:01:20.200
 the t2, okay.

24
00:01:20.900 --> 00:01:21.500
so here

25
00:01:26.100 --> 00:01:29.300
now we need to connect it with the relay as first one

26
00:01:29.300 --> 00:01:32.400
 is the signal second one is the plus and the

27
00:01:32.400 --> 00:01:35.500
 last one is the negative. So orange goes to

28
00:01:35.500 --> 00:01:38.700
 the signal red goes to the positive and

29
00:01:38.700 --> 00:01:42.100
 the Brown goes to the negative and

30
00:01:41.100 --> 00:01:45.000
 here we are good to go with that set up.

31
00:01:44.400 --> 00:01:47.600
 Okay, and in the last we

32
00:01:47.600 --> 00:01:50.200
 need to connect the lock with the

33
00:01:50.200 --> 00:01:50.800
 charger.

34
00:01:55.500 --> 00:01:58.300
And with the really to take a one cable.

35
00:01:59.700 --> 00:02:01.100
with the red

36
00:02:02.100 --> 00:02:04.400
and join the cables

37
00:02:11.300 --> 00:02:12.900
and take the screwdriver.

38
00:02:15.300 --> 00:02:16.400
Loose the nuts.

39
00:02:17.800 --> 00:02:18.800
of the comb

40
00:02:21.700 --> 00:02:24.700
and we have a comb and the NC normally

41
00:02:24.700 --> 00:02:25.200
 closed.

42
00:02:31.700 --> 00:02:34.100
Put that cable in the center in the comb.

43
00:02:44.400 --> 00:02:45.600
and the NC

44
00:02:48.100 --> 00:02:49.500
just put the log cable.

45
00:03:32.900 --> 00:03:34.600
And again attach that cable.

46
00:03:35.400 --> 00:03:36.400
With the red one.

47
00:03:44.800 --> 00:03:47.200
And now we are good to go with that. And in the next video

48
00:03:47.200 --> 00:03:50.600
 we're going to do the code how to enable the Bluetooth and

49
00:03:51.600 --> 00:03:54.600
how to send the data from the mobile

50
00:03:54.600 --> 00:03:54.900
 to

51
00:03:56.100 --> 00:03:59.500
esp32 and listen the data using a Bluetooth

52
00:03:59.500 --> 00:04:02.100
 serial terminal app, so I see you in

53
00:04:02.100 --> 00:04:03.600
 the next video. Have a good day. Bye.
