1
00:00:01,120 --> 00:00:07,990
With the latest update of aircraft engine or one engine stopped working for some of wireless cards so

2
00:00:07,990 --> 00:00:11,010
it works for some cards but for others it will not work.

3
00:00:11,020 --> 00:00:16,540
It'll actually say that it enables monitor mode on land 0 1.

4
00:00:16,720 --> 00:00:20,390
So instead of just 1 0 it's going to start calling them down 0 1.

5
00:00:20,770 --> 00:00:26,050
And when you try to use this card sometimes it's not going to work in monitor mode even though your

6
00:00:26,050 --> 00:00:27,780
card supports monitor mode.

7
00:00:27,790 --> 00:00:33,880
So for now I actually with Kelly to on with the new update I recommend using a different method of enable

8
00:00:33,990 --> 00:00:35,740
enabling monitor mode.

9
00:00:35,740 --> 00:00:40,360
Now this method is actually the manual method of enable and monitor mode.

10
00:00:40,960 --> 00:00:45,040
So my wireless card is actually that is zero so let's just have a look on it.

11
00:00:45,040 --> 00:00:47,670
So it's really config lines zero.

12
00:00:47,680 --> 00:00:49,060
This is my wireless card.

13
00:00:49,260 --> 00:00:51,740
And as you can see now it's in no.

14
00:00:52,060 --> 00:00:55,670
So what I'm gonna do is I'm going to enable it using the manual method.

15
00:00:55,780 --> 00:01:01,020
So I'm going to do if config Lan's zero down same way that we did in the previous method.

16
00:01:01,030 --> 00:01:02,860
And now the card is disabled.

17
00:01:02,860 --> 00:01:06,870
Now the next command is the command that's going to enable monitor mode on the card.

18
00:01:07,000 --> 00:01:12,240
So it's just going to be either a config Landseer or the name of the card.

19
00:01:12,410 --> 00:01:15,700
And then again I am going to say mood monitor.

20
00:01:15,970 --> 00:01:16,870
So it's very simple.

21
00:01:16,880 --> 00:01:22,180
Either contact is the command line zeroes the name of my wireless card and I'm Telenet to enable monitor

22
00:01:22,180 --> 00:01:24,200
mode on this card.

23
00:01:24,280 --> 00:01:27,010
So I'm going to hit enter and that's done.

24
00:01:27,070 --> 00:01:31,500
Now if you don't see any error messages that means the commands are running successfully.

25
00:01:31,540 --> 00:01:38,240
So now I'm going to enable the card again so I'm going to do if config lines are up and that's going

26
00:01:38,240 --> 00:01:45,930
to bring my card up and if I do I really can't take lines 0 as you can see now the card is in weiter

27
00:01:45,940 --> 00:01:46,340
mode.

28
00:01:46,480 --> 00:01:52,800
So and the next videos I've actually used the old method of enabling white or most of used air Ehrmann

29
00:01:52,820 --> 00:01:56,940
ngi and I'll be using one zero as my card and monitor mode.

30
00:01:57,010 --> 00:02:02,350
But if you use this method then Lazarro is the one that's going to be in weiter mode.

31
00:02:02,350 --> 00:02:11,270
So I'm going to be around arrow don't Renji I'm going to use Lan's zero instead of zero because my entire

32
00:02:11,270 --> 00:02:13,500
mode is enabled on Lan's you know.

33
00:02:13,550 --> 00:02:20,200
So as you can see now the card works perfectly and weiter mode is enabled on its.

34
00:02:20,420 --> 00:02:26,430
Now you have the freedom of choosing any method you want but this method will work on all cards where

35
00:02:26,630 --> 00:02:29,090
the aircraft or they are one entry method.

36
00:02:29,090 --> 00:02:33,490
The method that seen in the previous video will only work on some cards.

