1 00:00:08,600 --> 00:00:13,040 This is one of multiple videos discussing IP version six routing. 2 00:00:13,880 --> 00:00:20,120 In a previous video, I configured these two routers to use static IPV six routes. 3 00:00:22,740 --> 00:00:25,290 Using the local outgoing interface. 4 00:00:26,000 --> 00:00:29,960 What I'll do in this topology is remove that serial interface. 5 00:00:30,980 --> 00:00:35,480 And connect these routers using a Ethernet interface. 6 00:00:36,900 --> 00:00:44,310 So at the moment show IPV six Interface Brief shows us that this address is configured on the serial 7 00:00:44,310 --> 00:00:45,150 interface. 8 00:00:45,600 --> 00:00:50,790 So what I'll do is go into the serial interface and type no IPv6 address. 9 00:00:53,140 --> 00:00:58,450 So now we don't have an IPV six address configured on the serial interface. 10 00:00:59,460 --> 00:01:01,650 I'll do something similar on this side. 11 00:01:03,370 --> 00:01:06,190 No IPV six address. 12 00:01:08,310 --> 00:01:10,620 To show IPV six interface. 13 00:01:12,250 --> 00:01:20,260 We can see that the loopback is configured with an IPV six address, but no other addresses have been 14 00:01:20,260 --> 00:01:22,840 configured on any interfaces. 15 00:01:24,190 --> 00:01:34,600 So what we'll do now is shut the first Ethernet interface and configure the IP version six address on 16 00:01:34,600 --> 00:01:36,160 the Ethernet interface. 17 00:01:37,560 --> 00:01:45,840 So IPV six address and the specific address show IPV six interface. 18 00:01:47,980 --> 00:01:50,830 Shows us that this interface is up up. 19 00:01:51,280 --> 00:01:57,640 The link local address used is thus the global unicast address used is this. 20 00:01:58,240 --> 00:02:04,390 The router has joined all hosts on the local segment and all routers on the local segment multicast 21 00:02:04,390 --> 00:02:07,540 groups and it's joined some other groups as well. 22 00:02:07,990 --> 00:02:10,330 Show IPV six interface brief. 23 00:02:11,570 --> 00:02:20,090 Shows us the local address as well as the global unicast address configured on the router show IPV six 24 00:02:20,090 --> 00:02:20,840 route. 25 00:02:22,370 --> 00:02:27,600 Shows us connected route and local route link. 26 00:02:27,620 --> 00:02:30,620 Local addresses are not added to the routing table. 27 00:02:30,950 --> 00:02:35,630 We also see information for the loopback that was previously configured. 28 00:02:36,230 --> 00:02:39,950 So on this side, interface f0/0. 29 00:02:40,490 --> 00:02:41,600 No shut. 30 00:02:41,630 --> 00:02:46,190 IPV six Address 2001 colon one colon. 31 00:02:46,190 --> 00:02:47,150 Colon two. 32 00:02:47,480 --> 00:02:49,430 Slash 64. 33 00:02:50,150 --> 00:02:51,740 Ping 2001. 34 00:02:51,740 --> 00:02:53,000 Colon one colon. 35 00:02:53,000 --> 00:02:54,020 Colon one. 36 00:02:54,410 --> 00:03:01,700 Router two is able to ping router one using the first Ethernet interface show IPV six root. 37 00:03:02,660 --> 00:03:07,190 Only shows connected and local routes in the routing table. 38 00:03:07,430 --> 00:03:09,740 And that's true on both routers. 39 00:03:10,580 --> 00:03:12,020 Now a static route. 40 00:03:13,130 --> 00:03:15,740 Does exist in the running config. 41 00:03:16,710 --> 00:03:20,460 But that's not used because the local interface has gone down. 42 00:03:20,880 --> 00:03:22,380 But what I'll do here. 43 00:03:24,880 --> 00:03:26,320 Is remove that rut. 44 00:03:26,680 --> 00:03:28,420 We can do the same on the side. 45 00:03:31,720 --> 00:03:34,390 So no IPv6 route. 46 00:03:38,610 --> 00:03:46,380 To remove the rot show IPV six rot again shows us that we only have local. 47 00:03:47,500 --> 00:03:50,170 And connected routes in the routing table. 48 00:03:50,950 --> 00:03:58,450 So to allow router two to ping the loopback of router one, what we would do is type IPv6 route, specify 49 00:03:58,450 --> 00:04:06,340 the destination network which is 2001 colon face colon one colon colon slash 64. 50 00:04:07,860 --> 00:04:12,540 We can specify an interface or the next hop IP address. 51 00:04:13,470 --> 00:04:17,000 So the next hop IP address is going to be 2001. 52 00:04:17,010 --> 00:04:18,209 Colin one, Colin. 53 00:04:18,209 --> 00:04:22,290 Colin one and we can specify an administrative distance for the. 54 00:04:22,680 --> 00:04:26,730 I'm not going to do that show IPV six rot. 55 00:04:27,120 --> 00:04:32,850 We now have the static rot in the routing table and we should be able to paying. 56 00:04:32,880 --> 00:04:33,960 2001. 57 00:04:33,960 --> 00:04:35,040 Colin face. 58 00:04:35,070 --> 00:04:35,820 Colin one. 59 00:04:35,820 --> 00:04:36,420 Colin. 60 00:04:36,420 --> 00:04:37,320 Colin one. 61 00:04:37,620 --> 00:04:38,640 And we can. 62 00:04:39,830 --> 00:04:42,290 Ken wrote a one ping the loopback of router two. 63 00:04:42,620 --> 00:04:43,820 Not at the moment. 64 00:04:43,880 --> 00:04:53,090 We have to configure a root so to so IPv6 root 2001 face to slash 64. 65 00:04:54,420 --> 00:04:58,920 Specify a next hop of 2000 112. 66 00:05:00,240 --> 00:05:04,980 So can we paying 2001 face to one? 67 00:05:05,010 --> 00:05:13,950 Yes, we can show IPV six route shows us the static route in the routing table, but in this example, 68 00:05:13,950 --> 00:05:16,290 it's via the next hop IP address. 69 00:05:16,980 --> 00:05:19,290 Same is true over here. 70 00:05:19,770 --> 00:05:26,730 So that's different to the previous example where I configured the IPv6 static route using the local 71 00:05:26,730 --> 00:05:28,980 outgoing interface of the router. 72 00:05:29,710 --> 00:05:33,610 So that was an example of how to configure IPv6 study grants. 73 00:05:33,910 --> 00:05:35,650 I hope you've enjoyed this video. 74 00:05:35,770 --> 00:05:41,320 If it's been of benefit to you, please like it and please subscribe to my YouTube channel. 75 00:05:41,800 --> 00:05:43,570 I wish you all the very best.