1
00:00:00,860 --> 00:00:07,610
Now rather than configuring switch to manually, I've created the script that accomplishes the same

2
00:00:07,610 --> 00:00:08,150
thing.

3
00:00:08,330 --> 00:00:15,170
So tap enable conf to change the host name to switch to shut down any unused interfaces.

4
00:00:15,170 --> 00:00:26,960
So gigabit 1/123 gigabit 2/023 gigabit 3/023 will change the mode to transparent and then configure

5
00:00:26,960 --> 00:00:28,490
the VLANs on the switch.

6
00:00:29,030 --> 00:00:31,280
So I'll simply copy that config.

7
00:00:32,090 --> 00:00:34,970
Go to the console of switch two.

8
00:00:35,180 --> 00:00:41,810
So iOS vl2 hyphen to the switch and then I'll paste that config in.

9
00:00:43,330 --> 00:00:45,130
Interfaces have gone down.

10
00:00:45,370 --> 00:00:48,310
So as you can see, the host name of the switch has changed.

11
00:00:48,340 --> 00:00:55,930
Previously it was called switch, but now it's switched to show VLAN.

12
00:00:56,020 --> 00:01:07,690
Brief shows me VLAN ten and 20 show http status shows me that this switch is configured in transparent

13
00:01:07,690 --> 00:01:08,350
mode.

14
00:01:08,830 --> 00:01:11,590
Show IP interface brief.

15
00:01:12,190 --> 00:01:16,510
Shows me that all unused interfaces have been shut down.

16
00:01:17,140 --> 00:01:21,880
Show Run will allow me to see the full config of the switch.

17
00:01:22,120 --> 00:01:26,020
So as an example, here you can see the VLANs that were configured.

18
00:01:27,280 --> 00:01:30,070
You can see that ports have been shut down.

19
00:01:30,520 --> 00:01:35,830
Now, what I didn't do on the previous switch is save the config.

20
00:01:35,980 --> 00:01:40,000
So let's save the config on both these switches before we go any further.

21
00:01:40,630 --> 00:01:46,910
So on switch one, I've saved the config and on switch two, I've saved it.

22
00:01:46,930 --> 00:01:52,280
You can see that the configuration was compressed and has been saved successfully.

23
00:01:52,300 --> 00:01:54,310
So shows start up.

24
00:01:57,550 --> 00:02:03,280
Config shows me the configuration that we saved.

25
00:02:03,820 --> 00:02:09,100
As you can see here shows startup and we're using so many bytes out of so many bytes.

26
00:02:09,400 --> 00:02:12,850
Last configuration change was made on the 5th of July.

27
00:02:13,030 --> 00:02:16,030
Now for switch three.

28
00:02:16,060 --> 00:02:17,740
What do we need to configure here?

29
00:02:18,220 --> 00:02:20,110
Well, we need to change the switch name.

30
00:02:20,320 --> 00:02:23,710
We need to shut down any unused interfaces.

31
00:02:26,340 --> 00:02:32,490
Under this switch we are only using interfaces gigabyte 0001 and zero two.

32
00:02:32,610 --> 00:02:40,800
So gigabit zero three is not being used so that interface can be shut down and then any other interfaces

33
00:02:40,830 --> 00:02:42,720
on the switch can be shut.

34
00:02:43,560 --> 00:02:46,650
Now it's a good idea just to confirm the interfaces on the switch.

35
00:02:46,650 --> 00:02:49,320
So show IP interface brief.

36
00:02:50,060 --> 00:02:52,760
Shows me the various interfaces.

37
00:02:52,850 --> 00:02:57,890
So the only interfaces that we need are 0001 and zero two.

38
00:02:57,920 --> 00:02:59,640
Those three interfaces.

39
00:02:59,660 --> 00:03:05,780
All other interfaces on the switch can be shut down, and that's what we're going to do through this

40
00:03:05,780 --> 00:03:06,740
config.

41
00:03:06,920 --> 00:03:12,320
I'm also going to enable the switches of transparent switch and configure VLANs ten and 20.

42
00:03:12,470 --> 00:03:14,690
So let's paste that config in.

43
00:03:16,600 --> 00:03:17,740
Top End.

44
00:03:18,410 --> 00:03:22,130
And then I'll save the config.

45
00:03:22,340 --> 00:03:23,870
Now for CNA.

46
00:03:24,170 --> 00:03:29,630
You would be expected to know the full command copy running config.

47
00:03:29,630 --> 00:03:31,100
Startup config.

48
00:03:31,860 --> 00:03:36,030
And then press enter to save the configuration to the startup config.

49
00:03:36,510 --> 00:03:39,900
But for the real world, war is the old command.

50
00:03:40,440 --> 00:03:46,460
That saves a lot of time and it doesn't prompt you to specify where you want to save the file.

51
00:03:46,470 --> 00:03:49,200
It simply saves it to the startup config.

52
00:03:49,200 --> 00:03:52,470
So that's a lot quicker and hence we're using that here.

53
00:03:52,830 --> 00:03:58,140
So we've configured switch three, let's configure switch for switch over here.

54
00:03:58,170 --> 00:04:05,340
So this will be exactly the same as switch three same interfaces gigabyte 0001 and zero two will be

55
00:04:05,340 --> 00:04:05,910
used.

56
00:04:05,910 --> 00:04:12,810
All other interfaces will be shut down and we'll configure VLAN ten and 20 onto that switch.

57
00:04:13,050 --> 00:04:20,490
Now you might say that you don't actually need a VLAN ten on the switch because we only have hosts in

58
00:04:20,490 --> 00:04:23,640
VLAN 20 connected to the switch and that would be correct.

59
00:04:23,790 --> 00:04:29,820
But I'm going to keep the VLANs consistent on all my switches because we may want to add a host in VLAN

60
00:04:29,820 --> 00:04:34,110
ten to the switch and a host in VLAN 20 to the switch.

61
00:04:34,110 --> 00:04:36,240
So copy the config.

62
00:04:36,270 --> 00:04:39,720
Go to the console of switch four.

63
00:04:40,050 --> 00:04:43,980
So notice four and then paste it in.

64
00:04:46,730 --> 00:04:50,180
Control Z or control Z, save the config.

65
00:04:50,660 --> 00:04:56,000
So we've configured the links on the switches, configured the names of the switches.

66
00:04:56,000 --> 00:04:58,380
We now need to configure the routers.

67
00:04:58,400 --> 00:05:03,260
So on router one and I'll just do this manually because it'll be quick.

68
00:05:03,650 --> 00:05:09,320
Rather one is just booted and we've got the initial system configuration dialog asking us whether we

69
00:05:09,320 --> 00:05:10,190
want to enter that.

70
00:05:10,190 --> 00:05:16,100
I'm going to say no, I'm going to manually configure the router, so I don't want to go through the

71
00:05:16,100 --> 00:05:22,610
initial configuration dialog in this example and I press return to continue.

72
00:05:25,590 --> 00:05:27,810
You can see various interfaces are coming up.

73
00:05:30,080 --> 00:05:35,930
So top enable conf tt interface if 0/0.

74
00:05:35,960 --> 00:05:43,070
Now before I configure interfaces, notice when I type do show IP interface brief on the router.

75
00:05:44,000 --> 00:05:50,630
Router interfaces are administratively down by default unlike switch interfaces, so I don't need to

76
00:05:50,780 --> 00:05:51,980
disable interfaces.

77
00:05:51,980 --> 00:05:54,680
What I need to do is enable the interface.

78
00:05:55,130 --> 00:05:59,780
Before I enable the interface, I'll configure the IP address of this router.

79
00:05:59,870 --> 00:06:08,360
So I'll configure this 10.1, 10.11 with a subnet mask of slash 24 and then I'll no shut the interface

80
00:06:08,360 --> 00:06:09,140
of the router.

81
00:06:10,160 --> 00:06:19,520
I also need to configure the name, so I'm just going to configure that as router one and then save

82
00:06:19,520 --> 00:06:20,540
the config.

83
00:06:20,750 --> 00:06:26,930
So all I've done is know shut the interface and configure an IP address on Fost Ethernet zero zero on

84
00:06:26,930 --> 00:06:30,920
router one on router two will do something similar.

85
00:06:33,150 --> 00:06:37,830
So we'll bypass the initial configuration dialog press enter to continue.

86
00:06:42,310 --> 00:06:48,840
Top enable top tx change the name of the strata to route A to go into the first Ethernet interface.

87
00:06:48,850 --> 00:06:51,220
No, shut it and give it an IP address.

88
00:06:53,200 --> 00:06:55,450
Of 10.1 to 20.12.

89
00:06:56,800 --> 00:07:02,380
And Slash 24 Mosk show IP interface brief.

90
00:07:04,280 --> 00:07:07,970
That IP address is configured and the interface is up, up.

91
00:07:08,390 --> 00:07:09,860
Save the config.

92
00:07:11,520 --> 00:07:14,730
The lost device to configure initially is router three.

93
00:07:15,270 --> 00:07:16,410
Here it is.

94
00:07:16,830 --> 00:07:20,430
It's already been configured with the hostnames interface brief.

95
00:07:23,450 --> 00:07:25,250
Interfaces all shut down.

96
00:07:26,420 --> 00:07:31,550
So on first Ethernet zero zero, I'm going to shut it.

97
00:07:31,550 --> 00:07:39,260
And in this case I'll give it an IP address of ten .1. 102.253.

98
00:07:39,680 --> 00:07:49,670
We'll use 2544 HSP later, so I'll configure an IP address on this interface of ten.

99
00:07:49,970 --> 00:07:52,670
So at 1.102 five three.

100
00:07:54,610 --> 00:08:02,110
So that's the IP address of router three on fast Ethernet zero zero interfaces up going to the Fost

101
00:08:02,110 --> 00:08:09,250
Ethernet zero one interface that interfaces currently down and hasn't got an IP address assigned to

102
00:08:09,250 --> 00:08:09,700
it.

103
00:08:10,330 --> 00:08:17,680
So rather than configuring the IP address manually, I'm going to type IP address DHCP so that it gets

104
00:08:17,680 --> 00:08:22,660
an IP address from my local physical network.

105
00:08:23,440 --> 00:08:30,820
And when I no shut the interface, what we should see in a moment is that it gets an IP address through

106
00:08:30,820 --> 00:08:31,870
DHCP.

107
00:08:32,289 --> 00:08:37,059
At the moment we still waiting for an address to be assigned, but there you go.

108
00:08:37,120 --> 00:08:44,169
This address, 1921681 128 has been assigned via DHCP to router three.

109
00:08:44,380 --> 00:08:52,450
So show IP interface brief once again, notice IP address is configured on this interface that was allocated

110
00:08:52,540 --> 00:08:58,210
via my local DHCP server, which is actually my DSL router here at home.

111
00:08:58,870 --> 00:09:00,250
I'll save the config.

112
00:09:00,250 --> 00:09:05,830
So we have an IP address configured on Fost Ethernet zero zero and we have an IP address configured

113
00:09:05,830 --> 00:09:07,690
on Fost Ethernet zero one.

114
00:09:08,170 --> 00:09:12,250
What I haven't done is configure IP addresses on the switches.

115
00:09:12,250 --> 00:09:13,570
So let's do that.

