1
00:00:00,690 --> 00:00:02,530
Hello and welcome to this annual lesson.

2
00:00:03,630 --> 00:00:12,960
As usual, the first thing that we do when we start exploring a new hardware is to blank led or to write

3
00:00:12,960 --> 00:00:20,880
a programming sentence, which is hello, worst case for our hardware, which is SB 32, the example

4
00:00:20,880 --> 00:00:22,940
will be led blinking.

5
00:00:23,550 --> 00:00:35,420
So let's go to the examples menu and the Arduino idea and open up the sketch example or plunk example

6
00:00:36,300 --> 00:00:36,840
now.

7
00:00:38,080 --> 00:00:44,590
As you can see, we have a lot of examples here, you can go to the basics and click blink.

8
00:00:46,100 --> 00:00:47,560
Now, let's close this window.

9
00:00:48,570 --> 00:00:51,500
Let's open up this one now.

10
00:00:52,970 --> 00:00:58,490
As you can see in this lesson on this code, let me zoom.

11
00:01:00,550 --> 00:01:10,150
We have the lid set to default, which is led number 13 on Arduino, so we need to change this number.

12
00:01:10,660 --> 00:01:17,240
As you know, the SB 32 has a built in lid that is connected to its Gilberto's input output.

13
00:01:17,260 --> 00:01:24,070
Number two, it is important to check if Lyd pollution is automatically recognized by IDC.

14
00:01:24,370 --> 00:01:28,270
If not, you must add to called a line like this.

15
00:01:28,790 --> 00:01:29,290
Right.

16
00:01:29,290 --> 00:01:29,740
And.

17
00:01:33,210 --> 00:01:45,060
And right lead letters copied and pasted here and now you have to write to to make sure that the code

18
00:01:45,810 --> 00:01:55,320
will be saved to PIN number two, which is the internal lid pin inside the sport.

19
00:01:56,130 --> 00:01:57,810
Now let's save our code.

20
00:02:04,490 --> 00:02:05,990
Let's leave the name blank.

21
00:02:07,130 --> 00:02:08,570
And let's roll this.

22
00:02:10,740 --> 00:02:17,940
Now, as you can see, it's the very same court that we use and you we have two methods, the voice

23
00:02:17,940 --> 00:02:20,520
setup method and the voice method.

24
00:02:21,430 --> 00:02:30,690
The voice method is basically where you set up things like up in here we have PIN number two, which

25
00:02:30,690 --> 00:02:35,390
is the variable, and we can replace it with number two here.

26
00:02:35,760 --> 00:02:40,470
But since we are using a variable, we can apply the variable name here and here.

27
00:02:40,470 --> 00:02:45,960
We can assign it as input or output since we are dealing with a it's an output.

28
00:02:45,960 --> 00:02:54,570
So we write output and we use Benmore function to make sure that we set number two as output in the

29
00:02:54,570 --> 00:02:56,070
setup loop.

30
00:02:56,430 --> 00:03:03,030
Now the loop function from its name, it will keep repeating itself.

31
00:03:03,030 --> 00:03:05,810
The loop function runs over and over again forever.

32
00:03:06,990 --> 00:03:11,860
Once you stop the program or stop turn off the power, it will stop running.

33
00:03:12,420 --> 00:03:15,330
Now the digital right will write a digital value.

34
00:03:15,810 --> 00:03:23,740
High means one logic or turn on to the spin, which has been number two that has internal.

35
00:03:23,760 --> 00:03:31,200
And then the delay sentence will wait for a second and we will write the same sentence are right.

36
00:03:31,320 --> 00:03:38,180
We will write additional value, which is low or zero or off, and we will wait for another second.

37
00:03:38,190 --> 00:03:39,870
So we will turn on the.

38
00:03:40,890 --> 00:03:41,690
Wait a second.

39
00:03:41,700 --> 00:03:45,810
Turn it off and wait another second now before.

40
00:03:46,930 --> 00:03:54,100
Applauding this court, we need to go and make sure that we have that do it SB 32 different version,

41
00:03:54,100 --> 00:03:58,480
one selected, and we need to make sure that we have the right Gombauld.

42
00:03:59,320 --> 00:04:02,050
After that, we can simply click upload.

43
00:04:07,770 --> 00:04:09,030
It will take some time.

44
00:04:09,460 --> 00:04:17,580
OK, as you can see, you now have an error because this is a system variable, we can't change it with

45
00:04:17,580 --> 00:04:18,990
another name led to.

46
00:04:22,770 --> 00:04:23,840
Let's try it again.

47
00:04:41,890 --> 00:04:46,060
As you can see now, it's writing the code, done uploading.

48
00:04:47,560 --> 00:04:55,630
Now, if you have the board, you can see that there is a blue light blinking on and off.

49
00:05:00,770 --> 00:05:01,320
That's it.

50
00:05:01,340 --> 00:05:10,160
This is how simple it is to turn on or off alland you can use any other pin or connect an external lid

51
00:05:10,160 --> 00:05:11,030
if you have one.

52
00:05:11,600 --> 00:05:13,000
But that's it for this lesson.

53
00:05:13,010 --> 00:05:16,540
As you can see, it's the very same code that we use and Arduino.

54
00:05:17,330 --> 00:05:18,830
So it's really simple.

55
00:05:19,820 --> 00:05:22,270
It's really easy to get started with this board.

56
00:05:22,580 --> 00:05:27,710
You don't have a lot of knowledge, just basic knowledge encoding and an arduino.

57
00:05:28,130 --> 00:05:33,680
And if you don't have a basic knowledge, I already explained each line of code inside this sketch.

58
00:05:34,070 --> 00:05:38,030
If you have any question about anything, please ask in the Q&A board.

59
00:05:40,350 --> 00:05:41,220
Thanks for watching.

60
00:05:45,540 --> 00:05:47,940
This is Usrah from educational engineering team.