1
00:00:01,090 --> 00:00:01,730
Hello.

2
00:00:01,780 --> 00:00:03,650
Today we will talk about middle income.

3
00:00:04,330 --> 00:00:09,650
What is cut on count is the flow of electrons through a conductor.

4
00:00:09,650 --> 00:00:14,980
The water analogy is that current is like the water flowing through a hose.

5
00:00:15,020 --> 00:00:19,030
Count is measured in ambers and show from those.

6
00:00:19,070 --> 00:00:26,900
This illustration when Amber is a large number of electrons flowing past a spot in the conductor and

7
00:00:27,010 --> 00:00:28,410
the conductor in one second.

8
00:00:28,430 --> 00:00:37,400
As you can see in this illustration one Amber equals the number of electrons.

9
00:00:37,400 --> 00:00:39,490
I want to read it in one second.

10
00:00:40,550 --> 00:00:50,680
Um can't in normal electronics can be in the range of hundreds of arms to millions of micros two billionth

11
00:00:50,900 --> 00:00:52,850
of an S Nanos.

12
00:00:53,200 --> 00:01:00,770
You will generally work with 10 tons of amps down to Microsoft's arms in the typical electronic devices.

13
00:01:00,770 --> 00:01:08,570
You can deal with higher value than 10 arms since they require special device for measuring them and

14
00:01:08,570 --> 00:01:16,550
they are mainly used in factories not in everyday electronics or in circuits or common circuits.

15
00:01:16,940 --> 00:01:22,280
So now let's look at current measurements.

16
00:01:22,310 --> 00:01:29,630
There is greatest potential for meter damage when measuring current than any other function.

17
00:01:29,840 --> 00:01:36,840
Just as in voltage there is two kinds of current associated with the voltage AC and DC.

18
00:01:36,890 --> 00:01:44,390
This meter will only measure DC more expensive meter will measure both currents to measure current the

19
00:01:44,390 --> 00:01:51,370
Volt o meter must be inserted into this into the circuit so that the current flows through the meter.

20
00:01:51,530 --> 00:01:57,100
There is no way that you place the positive and negative robs and say I just measured current.

21
00:01:57,260 --> 00:02:03,030
This won't work like voltage you must place it in the circuit not on the circuit.

22
00:02:03,260 --> 00:02:10,750
So we must uh again mention safety during these measurements.

23
00:02:11,090 --> 00:02:23,900
And um we must spend some time to amplify your knowledge in how to use the Volt o meter to measure current.

24
00:02:23,900 --> 00:02:32,810
The right way and we mention that the current must flow through the meter us or both measuring voltage

25
00:02:32,810 --> 00:02:39,380
when it was only necessary to Sam but the voltage surrounding the source generally to have the current

26
00:02:39,380 --> 00:02:47,630
flow through the volt meter an existing circuit must be broken and sold out and the meter probes connected

27
00:02:47,630 --> 00:02:49,680
to either side of the break.

28
00:02:49,820 --> 00:02:57,190
The 4 volt o meter then becomes part of the path through which that comment must flow.

29
00:02:57,240 --> 00:03:04,980
There are two current ranges high up in arms and low and 200 million arms or both two arms and below

30
00:03:05,820 --> 00:03:13,200
internal fuses provide some meta protection for over current situation because there is such a wide

31
00:03:13,200 --> 00:03:15,660
range of current scales.

32
00:03:15,720 --> 00:03:19,830
There are two physical blobs jugs for that oranges.

33
00:03:19,860 --> 00:03:22,120
This allows for better protection.

34
00:03:22,540 --> 00:03:29,790
A hard refused to handle up to the arms of current and a more fragile fuse to protect the sensitive

35
00:03:29,790 --> 00:03:33,780
circuits needed to match up small currents.

36
00:03:33,810 --> 00:03:42,420
Now we will see these two ranges in diameter but we must read that caution.

37
00:03:42,420 --> 00:03:49,020
There must be some resistance in the circuit or the current flow through the circuit will be the maximum

38
00:03:49,590 --> 00:03:54,050
the source will produce and this current level could damage the Volt or meter.

39
00:03:54,540 --> 00:03:57,510
So your Jamal must make sure that there is some resistance.

40
00:03:57,510 --> 00:04:05,670
You must not connect the bolt on Meet up to Mr Khan directly and placed inside the circuit.

41
00:04:05,670 --> 00:04:12,180
In other words do not connect the Volt o meter blobs directly across the battery bro balls in the current

42
00:04:12,240 --> 00:04:13,630
measurement function.

43
00:04:13,650 --> 00:04:17,010
This is useless and it wont.

44
00:04:17,250 --> 00:04:25,110
It will damage your Volt or meter so with no resistance in the circle the voltage source will provide

45
00:04:26,170 --> 00:04:33,010
the full current available to the circuit there is essentially no resistance in the Volt or meter probe

46
00:04:33,010 --> 00:04:33,880
lines.

47
00:04:33,880 --> 00:04:39,460
Therefore if the blobs are connected directly across the battery ball the full current in the battery

48
00:04:39,670 --> 00:04:45,860
will flow through the Volt or meter and wobbly blows a fuse.

49
00:04:46,090 --> 00:04:53,070
So we must make sure that there is some kind of resistance in that circuit.

50
00:04:53,080 --> 00:04:59,130
If the very very isn't your must replace resistance inside that circuit.
