﻿1
00:00:02,216 --> 00:00:08,831
[music]

2
00:00:08,832 --> 00:00:12,558
Okay the next tunnels we're
going to look at are DMVPN.

3
00:00:12,559 --> 00:00:18,261
These are probably the more common,
more modern way of doing this,

4
00:00:18,261 --> 00:00:23,698
the transport IPv6 over
an IPv4 only network.

5
00:00:23,698 --> 00:00:28,601
The advantage of this is of course
the D means dynamic the M means

6
00:00:28,602 --> 00:00:33,476
multipoint. So we already have the
dynamic and the multipoint part

7
00:00:33,477 --> 00:00:39,869
in here. Now, we just got done looking
at two other dynamic multipoint

8
00:00:39,869 --> 00:00:41,599
methods of doing this.

9
00:00:41,600 --> 00:00:46,419
So what makes DMVPN so much better?

10
00:00:46,420 --> 00:00:50,257
First off it's a lot easier
to do security with it.

11
00:00:50,258 --> 00:00:57,280
The other piece is you're going to
see the hub doesn't need a whole

12
00:00:57,281 --> 00:00:58,453
lot of config.

13
00:00:58,454 --> 00:01:00,915
In fact it's actually the
simplest part of this,

14
00:01:00,915 --> 00:01:06,551
and then all the spokes get
almost identical configs.

15
00:01:06,552 --> 00:01:12,288
So that's really the big
advantage to this whole thing,

16
00:01:12,289 --> 00:01:19,219
is that you have very, very simple
config and it does everything

17
00:01:19,219 --> 00:01:22,725
you need it to do, our dynamic
routing protocols can run over it,

18
00:01:22,726 --> 00:01:24,536
no problem at all.

19
00:01:24,537 --> 00:01:27,337
So that's what we're going to do.

20
00:01:27,337 --> 00:01:31,737
We're going to jump in. We're going to set
this up. It's actually really easy to do.

21
00:01:31,737 --> 00:01:38,506
So once again, we'll be using our
same VPN topology but this time,

22
00:01:38,507 --> 00:01:42,550
we're going to be focusing on
just all the customer A sites.

23
00:01:42,550 --> 00:01:47,373
So we're going to be doing
Switch 1, Switch 2,

24
00:01:47,374 --> 00:01:49,218
and Router 6 here.

25
00:01:49,219 --> 00:01:53,106
That way, we can actually
have multipoint tunnels.

26
00:01:53,107 --> 00:01:59,432
We will use Router 1 as our hub,
and we will use Routers 4 and 5

27
00:01:59,433 --> 00:02:03,361
as our spoke routers with
the networks behind them.

28
00:02:03,361 --> 00:02:08,344
So let's again jump over the command
line here and I'm already on

29
00:02:08,345 --> 00:02:12,039
Router 1 as the hub, so here we
go, and this is where again,

30
00:02:12,039 --> 00:02:13,331
it's really nice.

31
00:02:13,331 --> 00:02:16,328
Actually before we get too far into this,

32
00:02:16,328 --> 00:02:20,626
we've been doing EIGRP this whole
time on our previous lessons.

33
00:02:20,627 --> 00:02:25,374
So I decided it would be a
good time to switch to OSPF.

34
00:02:25,374 --> 00:02:29,155
So that being the case, we do
actually need to fire that up here

35
00:02:29,156 --> 00:02:32,993
real quick. So let's go over-- we'll
start with the client devices,

36
00:02:32,994 --> 00:02:35,535
we'll start at Switch 1, and we'll say,

37
00:02:35,536 --> 00:02:40,680
interface loopback0 ipv6 ospf 1 area 0,

38
00:02:45,488 --> 00:02:53,073
loopback1 in area 0 and interface fa0/0.71.

39
00:02:53,074 --> 00:03:00,549
There's the switch, interface
vlan 71 in area 0.

40
00:03:00,550 --> 00:03:07,399
Switch 2, same basic thing, interface
loopback0 ipv6 ospf 1 area

41
00:03:07,400 --> 00:03:10,033
0. And this is of course
legacy OSPF config.

42
00:03:10,033 --> 00:03:15,020
We'll be doing fancier stuff
in MPLS in our next lesson.

43
00:03:15,020 --> 00:03:21,488
So interface loopback1 in
area 0, and interface VLAN.

44
00:03:21,488 --> 00:03:26,582
And this one up here is 84 in area 0.

45
00:03:27,848 --> 00:03:35,844
And then Router 6 interface
loopback0 ipv6 ospf 1 area 0,

46
00:03:35,845 --> 00:03:42,772
interface loopback1 area 0, interface g0/0.

47
00:03:42,772 --> 00:03:48,346
and that's 65 in area 0.

48
00:03:49,915 --> 00:03:57,145
Okay. That should pretty
much take care of those.

49
00:03:57,146 --> 00:04:06,508
Let's go to Router 1 now, and
interface FA00.71 IPv6 OSPF 1 area 0.

50
00:04:06,509 --> 00:04:10,235
So we fire up OSPF with the client router,

51
00:04:11,311 --> 00:04:14,097
same on Router 4.

52
00:04:15,433 --> 00:04:29,837
Interface FA0/0.84 neighbor
ship and Router 5.

53
00:04:37,385 --> 00:04:42,438
So that takes care of OSPF
running on the outer edges,

54
00:04:42,438 --> 00:04:44,473
now we could get to our tunnel.

55
00:04:44,474 --> 00:04:51,740
So Router 1 interface tunnel 0 and
there's two things we need to

56
00:04:51,741 --> 00:04:52,820
do right off the bat.

57
00:04:52,820 --> 00:04:58,229
First off IPv6 OSPF 1 area 0 before
we forget and it's not going

58
00:04:58,230 --> 00:05:00,469
to let me, okay so we can't do that first.

59
00:05:00,470 --> 00:05:03,290
Fine. Let's go ahead and
set this up normal,

60
00:05:03,291 --> 00:05:09,107
then. So IPv6 address FE80::1 link-local,

61
00:05:09,108 --> 00:05:22,907
and IPv6 address 2001:db8:100:200::1/64.

62
00:05:31,120 --> 00:05:35,077
We're just sort of using 200
for our tunnel interface here.

63
00:05:36,700 --> 00:05:51,194
Now we can say IPv6 OSPF 1 area 0, and IPv6
OSPF network type point-to-multipoint.

64
00:05:51,195 --> 00:05:54,739
Because it's the hub, so it's
definitely going to have to either

65
00:05:54,739 --> 00:05:59,104
be point-to-multipoint or broadcast.

66
00:05:59,104 --> 00:06:06,243
We'll start to point to multipoint,
this is essentially doing either

67
00:06:06,243 --> 00:06:11,866
phase one or phase two for DMVPN and
then we'll move this whole thing

68
00:06:11,867 --> 00:06:13,150
over here in a minute.

69
00:06:13,151 --> 00:06:17,345
But we'll at least just do phase
two, we'll turn it over to broadcast

70
00:06:17,345 --> 00:06:19,891
should only take about a moment.

71
00:06:19,892 --> 00:06:25,428
So that's what we need for
the IPv6 basic config.

72
00:06:25,428 --> 00:06:29,663
Don't forget we also need a tunnel
source and that's going to be

73
00:06:29,664 --> 00:06:33,159
on Router 1, that's going to be FA0/0.12.

74
00:06:35,050 --> 00:06:38,046
We could use a loop back too
it doesn't really matter.

75
00:06:38,047 --> 00:06:43,892
Then we need a tunnel mode.

76
00:06:45,169 --> 00:06:48,960
Is GRE my multipoint.

77
00:06:56,897 --> 00:07:01,802
So tunnel mode GRE multipoint
is what we typed in.

78
00:07:01,803 --> 00:07:06,704
Now we need a couple NHRP commands.

79
00:07:06,704 --> 00:07:09,847
NHRP is Next Hop Redundancy Protocol.

80
00:07:09,847 --> 00:07:15,065
It's what DMVPN uses to build the
dynamic mappings on how to get

81
00:07:15,066 --> 00:07:16,956
to remote sites.

82
00:07:16,956 --> 00:07:20,757
We're not going to get a whole
bunch into DMVPN this is again,

83
00:07:20,758 --> 00:07:26,886
just about changes from IPv4 to
IPv6 so I'm not going to get into

84
00:07:26,887 --> 00:07:27,944
a whole bunch here.

85
00:07:27,945 --> 00:07:32,463
Probably the best way to think of
NHRP if you're not real familiar

86
00:07:32,463 --> 00:07:41,129
with DMVPN is it's like ARP but
instead of ARP which does Layer 3

87
00:07:41,129 --> 00:07:45,592
to Layer 2 lookup, this
is Layer 3 to Layer 3.

88
00:07:45,593 --> 00:07:51,627
I want to get to this private address
through what public address?

89
00:07:51,628 --> 00:07:53,415
So, that's what we need to do.

90
00:07:53,415 --> 00:07:57,447
Now, the hub though is very, very
simple because it doesn't get that

91
00:07:57,447 --> 00:08:04,990
information. It just gets IPv6 , NHRP map,

92
00:08:04,991 --> 00:08:08,494
for multicast, learn it dynamics.

93
00:08:08,494 --> 00:08:11,071
That's so we can run
routing protocols over it,

94
00:08:11,071 --> 00:08:17,327
and then IPv6, NHRP, network
ID and give it a number.

95
00:08:17,327 --> 00:08:19,785
It doesn't really matter - network
ID 1 - we're not trying to run

96
00:08:19,786 --> 00:08:23,995
multiple networks over this
same tunnel interface,

97
00:08:23,995 --> 00:08:25,541
so that's fine.

98
00:08:25,541 --> 00:08:30,606
And at the end of this
whole thing, guess what?

99
00:08:30,607 --> 00:08:32,653
That's the config.

100
00:08:32,654 --> 00:08:35,896
Do show run interface tunnel 0.

101
00:08:35,896 --> 00:08:39,108
That's it. That's what we have.

102
00:08:41,837 --> 00:08:44,289
And we did turn on OSPF, correct?

103
00:08:44,290 --> 00:08:45,552
Yes we did, okay.

104
00:08:45,552 --> 00:08:57,897
So let's go over to Router 4 and
interface tunnel 0 IPv6 address

105
00:08:59,579 --> 00:09:05,612
FE80:: four link local.

106
00:09:13,719 --> 00:09:15,671
So, give him an address.

107
00:09:16,782 --> 00:09:24,141
Of course, IPv6 RSPF1
area 0 for consistency,

108
00:09:24,142 --> 00:09:26,538
and so we don't have to
change timers and stuff.

109
00:09:26,539 --> 00:09:32,466
We will change his network type
to point to multipoint as well.

110
00:09:33,475 --> 00:09:38,124
And then there's the stuff that
makes the spokes a little bit

111
00:09:38,124 --> 00:09:39,460
different from the hub.

112
00:09:39,460 --> 00:09:42,672
Now, I've put in the stuff
that's the same first,

113
00:09:42,673 --> 00:09:46,622
so first off, tunnel source FA0/0.

114
00:09:46,622 --> 00:09:50,165
and in this case it's 34.

115
00:09:52,456 --> 00:09:58,854
And tunnel mode GRE multipoint.

116
00:10:00,941 --> 00:10:10,312
And IPv6 NHRP network ID 1.

117
00:10:10,313 --> 00:10:12,074
So those things are the same.

118
00:10:12,075 --> 00:10:14,363
Those are things we had
put in on the other side,

119
00:10:14,363 --> 00:10:16,034
and they're going to be
the same on this side,

120
00:10:16,035 --> 00:10:19,679
the side of course in the
tunnel source may be different.

121
00:10:19,679 --> 00:10:24,229
Now, the next things are things
that we're going to need on the

122
00:10:24,229 --> 00:10:26,910
spokes, but not on the hub.

123
00:10:26,911 --> 00:10:33,604
So the first one is IPv6
NHRP map multicast.

124
00:10:33,604 --> 00:10:38,605
And all this part we had on the
hub, but the hub said dynamic.

125
00:10:38,606 --> 00:10:41,412
Actually you know what, I'm sorry.

126
00:10:41,413 --> 00:10:46,144
Before we do multicast we should
really map the address of the hub

127
00:10:46,145 --> 00:10:52,113
first. 2001 DB8:100:200::1.

128
00:10:52,114 --> 00:11:03,422
So that IPv6 address/64 is
available through what's his IPv4

129
00:11:03,422 --> 00:11:14,246
address. You can go back to the diagram
if you need to but it's 173.1.12.1.

130
00:11:14,246 --> 00:11:23,834
So I'm telling him that you can get
to his address on the cloud through

131
00:11:23,835 --> 00:11:26,034
that next hub.

132
00:11:26,035 --> 00:11:29,387
This is also where we're
going to map our multicast.

133
00:11:29,387 --> 00:11:40,120
So IPv6 NHRP map multicast to 173.1.12.1.

134
00:11:42,859 --> 00:11:56,000
Last but not least IPv6 NHRP next
hop server end point into that

135
00:11:56,001 --> 00:12:03,284
guy. Oops, not with the mask.

136
00:12:08,521 --> 00:12:16,068
OSPF just came up over the tunnel
which is always a really good sign.

137
00:12:16,069 --> 00:12:24,408
Do show run interface tunnel 0.

138
00:12:24,408 --> 00:12:26,599
So there's the spoke configuration.

139
00:12:30,213 --> 00:12:36,863
Here's the beautiful part about
the spoke configuration is we can

140
00:12:36,863 --> 00:12:48,264
grab this, we can copy this put it
in your favorite note editor and

141
00:12:48,264 --> 00:12:50,273
then just tweak it a little bit.

142
00:12:50,274 --> 00:12:53,623
So let's see this is going
to go on Router 5 next.

143
00:12:53,624 --> 00:12:57,720
So his link local is going
to be 5, oops not 51.

144
00:12:57,721 --> 00:12:59,970
Area 51 is a whole different thing.

145
00:13:01,147 --> 00:13:06,635
Five but guess what, that's
the same, that's the same,

146
00:13:06,635 --> 00:13:09,038
that's the same, that's the
same, that's the same,

147
00:13:09,039 --> 00:13:14,449
this is going to be different
because it's actually 35.

148
00:13:15,922 --> 00:13:26,519
That's it. Copy it, switch back to
your command line make sure you

149
00:13:26,520 --> 00:13:27,979
go to the right router.

150
00:13:31,825 --> 00:13:34,812
I want to make sure I have
that interface right.

151
00:13:34,812 --> 00:13:38,105
I said 35 I'm pretty sure that's right,

152
00:13:38,106 --> 00:13:41,320
yeah it is. Okay, and paste.

153
00:13:43,460 --> 00:13:47,092
Didn't really need an end
on that but that's okay.

154
00:13:47,093 --> 00:13:51,860
OSPF already came up, already a good sign.

155
00:13:51,861 --> 00:13:57,468
Now what this means is we should
be able to go to say Switch 1

156
00:13:57,469 --> 00:14:09,032
and say, Do trace 2001 DB8:100:8::8 good.

157
00:14:09,032 --> 00:14:14,659
Also somebody we haven't
hit yet 6::6 Router 6.

158
00:14:14,660 --> 00:14:22,182
You can see right here it went
to 1 and then 4 and here it went

159
00:14:22,183 --> 00:14:24,631
from 1 and then 5.

160
00:14:26,012 --> 00:14:32,349
So just like that DMVPN is
done and up and good to go.

161
00:14:34,194 --> 00:14:41,524
If you go to router-- let's
see we're on Switch 1.

162
00:14:41,525 --> 00:15:01,472
So let's go to switch two and say
do trace 2001 DB8:100:6::6 that

163
00:15:01,473 --> 00:15:04,460
should go through Router
1, so it goes to 4,

164
00:15:04,460 --> 00:15:07,049
to 1, to 5, to 6.

165
00:15:07,050 --> 00:15:11,231
Fine. Trace it a couple of
times, it'll do the same thing.

166
00:15:13,057 --> 00:15:17,724
This is what's referred
to as DMVPN Phase 1.

167
00:15:17,725 --> 00:15:26,084
Phase 1 essentially says that all
traffic has to go through the hub.

168
00:15:26,084 --> 00:15:31,838
So I'm learning all the routes, but
the next hop for all the routes,

169
00:15:31,838 --> 00:15:36,215
if I go to-- this is of course,
not taking place on Switch 2,

170
00:15:36,215 --> 00:15:38,133
it's taking place on Router 4.

171
00:15:38,133 --> 00:15:44,736
If I go to Router 4 and I
say, do show IPv6 route OSPF,

172
00:15:44,737 --> 00:15:50,507
all of his next hops, all point to
the link-local address of Router

173
00:15:50,507 --> 00:15:53,866
1. I mean, everything is not on this side,

174
00:15:53,866 --> 00:15:55,878
of course. Stuff on this
side is, of course,

175
00:15:55,879 --> 00:15:57,760
pointing to Switch 2.

176
00:15:57,761 --> 00:16:03,967
But everything else including 5's address.

177
00:16:03,967 --> 00:16:08,237
So you know Router 5's
address on the tunnel,

178
00:16:08,238 --> 00:16:12,942
Router 6 is loopback, all goes to Router 1,

179
00:16:12,943 --> 00:16:16,255
so that's essentially Phase 1.

180
00:16:16,256 --> 00:16:19,813
Now with Phase 1, I technically
wouldn't have to get all these routes,

181
00:16:19,813 --> 00:16:21,144
I could summarize.

182
00:16:21,145 --> 00:16:24,907
But we're not going down the
whole big DMVPN discussion here.

183
00:16:24,907 --> 00:16:30,169
But what I can do, just to show
you that it works fine for IPv6,

184
00:16:30,169 --> 00:16:34,014
is I could go to Router 1 and I could say,

185
00:16:34,015 --> 00:16:40,110
ipv6 ospf network broadcast.

186
00:16:42,430 --> 00:16:53,943
And then on 4, I'm on the interface,
ipv6 ospf network broadcast

187
00:16:53,943 --> 00:17:04,159
and ip ospf priority 0, so we
cannot become the DR or the BDR.

188
00:17:04,160 --> 00:17:10,430
Router 5, and I'm not under the tunnel.

189
00:17:28,183 --> 00:17:32,496
Okay. Give t:58.840000
 Stuff on this side is, of course, pointing
 to switch to, but everything

0:15:58.840000 --> 0:16:04.140000
 else, including, you
 know, five's address.

0:16:04.140000 --> 0:16:08.480000
 So, you know, router five's address
 on the, on the tunnel.

0:16:08.480000 --> 0:16:10.840000
 Router six is loop back.

0:16:10.840000 --> 0:16:13.240000
 All goes to router one.

0:16:13.240000 --> 0:16:16.080000
 So that's essentially phase one.

0:16:16.080000 --> 0:16:19.340000
 Now with phase one, I technically wouldn't
 have to get all these routes.

0:16:19.340000 --> 0:16:24.020000
 I could summarize, but we're not going
 down a whole big DMVPN discussion

0:16:24.020000 --> 0:16:30.220000
 here. But what I can do, just to show
 you that it works fine for IPV six,

0:16:30.220000 --> 0:16:40.240000
 is I can go to router one and I could
 say IPV six OSPF network broadcast.

0:16:40.240000 --> 0:16:44.360000
 And then on four.

0:16:44.360000 --> 0:16:47.160000
 I'm going to interface.

0:16:47.160000 --> 0:17:01.500000
 IPV six OSPF network broadcast and IPOSPF
 priority zero so we cannot become

0:17:01.500000 --> 0:17:27.920000
 the B.R. or the B.D.R.

0:17:27.920000 --> 0:17:32.640000
 Okay. Give this just a second
 and it should stabilize.

0:17:32.640000 --> 0:17:44.320000
 Right now they're in two way.

0:17:44.320000 --> 0:17:46.280000
 And it's got to wait for things
 to time out and stuff.

0:17:46.280000 --> 0:17:50.340000
 It might actually be faster.

0:17:50.340000 --> 0:17:51.720000
 Give it a second here.

0:17:51.720000 --> 0:17:54.280000
 You might have to bounce
 the tunnel interfaces.

0:17:54.280000 --> 0:18:08.020000
 I'm just going to do it.

0:18:08.020000 --> 0:18:11.220000
 This is usually faster.

0:18:11.220000 --> 0:18:28.920000
 And you're going to do this always
 bring the hub up first.

0:18:28.920000 --> 0:18:48.540000
 Now this OSPF neighborhood
 should come up.

0:18:48.540000 --> 0:18:50.020000
 Probably in the wait state.

0:18:50.020000 --> 0:18:51.600000
 You have to wait 40 seconds.

0:18:51.600000 --> 0:18:56.160000
 Do show IP OSPF interface brief.

0:18:56.160000 --> 0:19:01.240000
 I'm looking at IP.

0:19:01.240000 --> 0:19:03.740000
 I'm sitting there going like those
 aren't the right interfaces.

0:19:03.740000 --> 0:19:06.420000
 That's much better.

0:19:06.420000 --> 0:19:12.840000
 Okay. So he's the drother,
 which is good.

0:19:12.840000 --> 0:19:17.360000
 And then five. No shut.

0:19:17.360000 --> 0:19:23.080000
 It's already done before
 I came to command.

0:19:23.080000 --> 0:19:26.320000
 Okay. So OSPF is up
 and running now.

0:19:26.320000 --> 0:19:30.180000
 So now let's go back to our switch
 to do our trace again.

0:19:30.180000 --> 0:19:34.840000
 That's looking spectacular.

0:19:34.840000 --> 0:19:38.440000
 There we go. Okay.

0:19:38.440000 --> 0:19:43.600000
 So again, four to one to five to
 eight, just like we had before.

0:19:43.600000 --> 0:19:48.180000
 Four, one, five to six.

0:19:48.180000 --> 0:19:49.520000
 Eight to milliseconds.

0:19:49.520000 --> 0:19:51.200000
 I'm like, what is eight?

0:19:51.200000 --> 0:19:52.880000
 Okay. All right.

0:19:52.880000 --> 0:19:54.940000
 So four, one, five, eight.

0:19:54.940000 --> 0:20:01.500000
 Four, one, five, six.

0:20:01.500000 --> 0:20:06.640000
 Okay. Let's go to router three.

0:20:06.640000 --> 0:20:09.840000
 Yeah. I'm out of four, sorry.

0:20:09.840000 --> 0:20:13.540000
 Do show IPV six.

0:20:13.540000 --> 0:20:22.440000
 NHRP. And what you can see here.

0:20:22.440000 --> 0:20:25.100000
 So he's got that entry.

0:20:25.100000 --> 0:20:35.160000
 He's got the 200.

0:20:35.160000 --> 0:20:38.320000
 Is it a little bit
 interesting there?

0:20:38.320000 --> 0:20:54.380000
 So that's going through
 one and into five.

0:20:54.380000 --> 0:21:02.160000
 And then one and into five
 is not switching over.

0:21:02.160000 --> 0:21:05.240000
 All the traffic is going
 through the hub still.

0:21:05.240000 --> 0:21:10.660000
 Do show IPV six route OSPF.

0:21:10.660000 --> 0:21:17.080000
 So he has the right next hops now.


0:21:17.080000 --> 0:21:27.480000
 But for some reason
 it's not switching.

0:21:27.480000 --> 0:21:28.200000
 It's interesting.

0:21:28.200000 --> 0:21:33.500000
 Take a look at router one here.

0:21:33.500000 --> 0:21:43.020000
 Make sure everything worked okay.

0:21:43.020000 --> 0:21:45.420000
 And by the way, this is how you
 look at the cache, right?

0:21:45.420000 --> 0:21:50.400000
 So what this is basically telling
 you is, okay, so here's this host.

0:21:50.400000 --> 0:21:55.020000
 Okay. We're getting to him through that
 guy through this IPV four address

0:21:55.020000 --> 0:22:01.680000
 of 34.4. To get to router
 five, he's going to 35.5.

0:22:01.680000 --> 0:22:05.240000
 And then of course the link locals are
 getting registered as well to those

0:22:05.240000 --> 0:22:11.500000
 same addresses. So what we have going
 on here is both spokes are registering

0:22:11.500000 --> 0:22:13.460000
 with the hub. No problem.

0:22:13.460000 --> 0:22:19.460000
 And then we go to router four.

0:22:19.460000 --> 0:22:26.480000
 And he's learning.

0:22:26.480000 --> 0:22:35.780000
 That's the problem right there.

0:22:35.780000 --> 0:22:38.620000
 Yeah, he's learning
 it as a slash 64.

0:22:38.620000 --> 0:22:51.800000
 So yeah, he's going to continue
 to go to router one.

0:22:51.800000 --> 0:22:58.020000
 Let's try something behind it.

0:22:58.020000 --> 0:23:10.080000
 Let's try and go to
 six again from four.

0:23:10.080000 --> 0:23:25.520000
 He's still going to one.

0:23:25.520000 --> 0:23:27.380000
 That's actually really
 interesting.

0:23:27.380000 --> 0:23:29.640000
 Why is he going to one?

0:23:29.640000 --> 0:23:31.820000
 Oh, that'd be why.

0:23:31.820000 --> 0:23:42.220000
 Because he says that FE80 colon colon
 five goes to the NBMA address of

0:23:42.220000 --> 0:24:04.520000
 173.1.12.1. That's not what
 we're looking for here.

0:24:04.520000 --> 0:24:28.340000
 So let's try this one more time.

0:24:28.340000 --> 0:24:31.100000
 Let him re-register
 with the server.

0:24:31.100000 --> 0:24:33.160000
 Because see router
 one has it right.

0:24:33.160000 --> 0:25:03.080000
 34, 35, 34, 35. Okay, neighbor
 four just came up.

0:25:03.080000 --> 0:25:04.580000
 Yeah, the problem is
 he keeps learning.

0:25:04.580000 --> 0:25:12.120000
 He keeps learning the link local
 with the NBMA address of 12.1.

0:25:12.120000 --> 0:25:25.620000
 So we may have to actually
 say IPv6, NHRP, redirect.

0:25:25.620000 --> 0:25:35.420000
 And I'm router four,
 IPv6, NHRP, shortcut.

0:25:35.420000 --> 0:25:38.520000
 Shouldn't have to do this
 just for phase two.

0:25:38.520000 --> 0:25:40.640000
 This is really what you do when
 you go into phase three.

0:25:40.640000 --> 0:25:44.080000
 But it looks like for IPv6 with the
 link local, it's going to cause us

0:25:44.080000 --> 0:25:49.100000
 a problem. Oops.

0:25:49.100000 --> 0:25:53.820000
 See if that fixes it.

0:25:53.820000 --> 0:25:57.920000
 At this point it's working.

0:25:57.920000 --> 0:25:59.900000
 So it's not that big of a deal.

0:25:59.900000 --> 0:26:06.220000
 But I'd really rather see it
 do the actual peer to peer.

0:26:06.220000 --> 0:26:17.840000
 So let's clear this again.

0:26:17.840000 --> 0:26:35.820000
 So we only know about one now.

0:26:35.820000 --> 0:26:38.300000
 Now he's getting it incomplete.

0:26:38.300000 --> 0:26:41.440000
 And he's still going
 to go through one.

0:26:41.440000 --> 0:26:43.900000
 We might have to clear
 it on five too.

0:26:43.900000 --> 0:26:47.040000
 We'll do this one more time
 and see if it works.

0:26:47.040000 --> 0:26:49.740000
 We'll just bounce all these
 interfaces one more time.

0:26:49.740000 --> 0:26:52.840000
 Now that we turned
 on that feature.

0:26:52.840000 --> 0:27:01.120000
 For anybody who's not real familiar
 with DMVPN, what I'm trying to get

0:27:01.120000 --> 0:27:06.420000
 working here and for some silly reason
 it's not, is spoke to spoke.

0:27:06.420000 --> 0:27:10.060000
 I mean spoke to spoke through
 the hub is working just fine.

0:27:10.060000 --> 0:27:15.200000
 So just from a raw connectivity
 standpoint, it's working.

0:27:15.200000 --> 0:27:18.900000
 But what I'm trying to do is move us
 out of phase two slash phase or phase

0:27:18.900000 --> 0:27:23.020000
 one here, which is all traffic through
 the hub and get us over to something

0:27:23.020000 --> 0:27:26.800000
 a little more modern.

0:27:26.800000 --> 0:27:30.580000
 And again, I'm not trying this on
 this particular version of code.

0:27:30.580000 --> 0:27:32.800000
 So it's also possible here.

0:27:32.800000 --> 0:27:33.860000
 Then it doesn't work.

0:27:33.860000 --> 0:27:36.320000
 I run into a few things that don't
 work on particular code.

0:27:36.320000 --> 0:28:20.980000
 So the hub then let's trace it.

0:28:20.980000 --> 0:28:23.060000
 Oh, play hello, Vospey.

0:28:23.060000 --> 0:28:28.200000
 I came back up. There we go.

0:28:28.200000 --> 0:28:45.620000
 Might help. And now it's hitting
 incomplete negative.

0:28:45.620000 --> 0:28:48.480000
 So it's not going to switch over.

0:28:48.480000 --> 0:28:51.380000
 So either the code's not working
 or I missed something.

0:28:51.380000 --> 0:29:13.820000
 Let me give a real quick
 look at my configs.

0:29:13.820000 --> 0:29:16.300000
 And that's right.

0:29:16.300000 --> 0:29:42.160000
 And that all looks right.

0:29:42.160000 --> 0:30:09.000000
 I did have. And one more thing.

0:30:09.000000 --> 0:30:17.960000
 So he's got the next top right.

0:30:17.960000 --> 0:30:28.720000
 It's just not resolving
 the next top right.

0:30:28.720000 --> 0:30:55.500000
 Yep. So some reason he's hitting type
 incomplete flags negative trying

0:30:55.500000 --> 0:30:58.240000
 to do the switch over
 spoke to spoke.

0:30:58.240000 --> 0:31:01.780000
 So not going to spend a whole
 lot of time looking at this.

0:31:01.780000 --> 0:31:05.600000
 Again, we're not trying
 to focus here on DM VPN.

0:31:05.600000 --> 0:31:10.800000
 So obviously something's not quite set
 right here for some reason, though

0:31:10.800000 --> 0:31:12.740000
 everything looks right.

0:31:12.740000 --> 0:31:21.100000
 So as far as IPv6 over DM VPN though,
 working fine, no problem.

0:31:21.100000 --> 0:31:25.260000
 And again, still no IPv4
 on anything underneath.

0:31:25.260000 --> 0:31:27.740000
 So that's really all it takes
 to set it up and run it.

0:31:27.740000 --> 0:31:30.200000
 And by the way, there's another
 one you want to be aware of.

0:31:30.200000 --> 0:31:35.720000
 Do show DM VPN. Another good command
 that will actually show you what's

0:31:35.720000 --> 0:31:38.740000
 up for what addresses.

0:31:38.740000 --> 0:31:44.480000
 So another good one to keep
 your eyes on for NHRP.

0:31:44.480000 --> 0:31:50.280000
 And there's another one detail that
 adds a little bit more information,

0:31:50.280000 --> 0:31:53.820000
 particularly if you're running
 IP Sac over any of this.

0:31:53.820000 --> 0:31:56.460000
 And you're doing cryptography.

0:31:56.460000 --> 0:31:59.840000
 It shows you the crypto information
 down at the bottom.

0:31:59.840000 --> 0:32:02.880000
 So that's pretty cool as well.

0:32:02.880000 --> 0:32:06.620000
 So that's IPv6 over DM VPN.

