WEBVTT

0:00:05.060000 --> 0:00:08.700000
 With regards to my laptop, my laptop
 specifically that I'm working on

0:00:08.700000 --> 0:00:11.580000
 here, I was to draw this.

0:00:11.580000 --> 0:00:16.220000
 Well, my laptop is already here.

0:00:16.220000 --> 0:00:18.700000
 So here's my laptop.

0:00:18.700000 --> 0:00:25.460000
 And this laptop, it's not part of this
 picture here, but let me just put

0:00:25.460000 --> 0:00:30.300000
 in green, the terminal server, which
 was that special router with the

0:00:30.300000 --> 0:00:37.900000
 octal cable. Oops, terminal.

0:00:37.900000 --> 0:00:39.780000
 Oh, you just can't see the L.

0:00:39.780000 --> 0:00:42.660000
 Anyway, there we go.

0:00:42.660000 --> 0:00:57.440000
 So we know the terminal server had
 that octal cable coming out, which

0:00:57.440000 --> 0:01:14.100000
 then connected to the USB port.

0:01:14.100000 --> 0:01:19.500000
 I'll put that here as a little C.

0:01:19.500000 --> 0:01:24.200000
 That was connected to be that
 blue cable to my laptop.

0:01:24.200000 --> 0:01:29.980000
 And that was connected to the USB port
 on my laptop via that serial to

0:01:29.980000 --> 0:01:37.160000
 USB connector. Well the USB port on
 my laptop does not understand the

0:01:37.160000 --> 0:01:38.380000
 internet protocol.

0:01:38.380000 --> 0:01:41.760000
 It is not a place where
 I can put an IP address.

0:01:41.760000 --> 0:01:46.880000
 It can't send and receive packets
 to get me through this network.

0:01:46.880000 --> 0:01:51.500000
 So for that, I will need actually
 an ethernet connection.

0:01:51.500000 --> 0:01:53.520000
 I'll use brown here for that.

0:01:53.520000 --> 0:01:58.780000
 So I will still need to connect up to
 an access layer switch via ethernet.

0:01:58.780000 --> 0:02:01.100000
 And that's actually going to be the
 next section here I'm going to do

0:02:01.100000 --> 0:02:03.480000
 right here. I'm going to do
 these connections here.

0:02:03.480000 --> 0:02:07.960000
 I'm going to do an ethernet connection
 here between those two.

0:02:07.960000 --> 0:02:15.280000
 And I'm going to do an ethernet connection
 here between switch two and

0:02:15.280000 --> 0:02:22.340000
 router one. I've already drawn in my
 serial connections here, but I'll

0:02:22.340000 --> 0:02:24.740000
 just label them as serial.

0:02:24.740000 --> 0:02:29.040000
 Different kind of interface, different
 kind of protocol as far as how

0:02:29.040000 --> 0:02:31.760000
 we deal with electrical signaling.


0:02:31.760000 --> 0:02:34.960000
 And then we're going to
 go back to ethernet.

0:02:34.960000 --> 0:02:38.620000
 Of ethernet from router
 two to my switch.

0:02:38.620000 --> 0:02:42.800000
 And from the switch to this router
 over here which is serving as a web

0:02:42.800000 --> 0:02:51.480000
 server. So that's how I'm going
 to complete the cabling.

0:02:51.480000 --> 0:02:54.520000
 So right now the only cabling I've
 got are the green lines here.

0:02:54.520000 --> 0:02:57.960000
 My console cable going to my terminal
 server and then the octal port which

0:02:57.960000 --> 0:03:00.960000
 spreads out to the various
 console ports.

0:03:00.960000 --> 0:03:03.760000
 Let me just write that right here.


0:03:03.760000 --> 0:03:07.540000
 So each one of these little C's here represents
 the console port I'm connected

0:03:07.540000 --> 0:03:12.520000
 to on my various routers
 and switches.

0:03:12.520000 --> 0:03:16.020000
 But because I can't use that for actual
 sending and receiving of data

0:03:16.020000 --> 0:03:19.620000
 of IP packets, I need to get
 other types of interfaces.

0:03:19.620000 --> 0:03:22.880000
 Ethernet and serial involved.

0:03:22.880000 --> 0:03:24.560000
 So let me look at this
 here for a second.

0:03:24.560000 --> 0:03:28.860000
 Now you might be wondering, okay, well,
 for example, from the laptop to

0:03:28.860000 --> 0:03:34.700000
 the switch, how did you know you
 were supposed to use ethernet?

0:03:34.700000 --> 0:03:39.560000
 Well, so the device you're on, so the
 type of network connectivity you

0:03:39.560000 --> 0:03:42.980000
 will have is constrained by
 the device that you're on.

0:03:42.980000 --> 0:03:47.240000
 For example, if I'm talking about a
 smartphone or a tablet like an iPad

0:03:47.240000 --> 0:03:52.120000
 or something, I can't use wired ethernet
 because a smartphone and a tablet,

0:03:52.120000 --> 0:03:57.480000
 they don't have jacks that
 look like this, right?

0:03:57.480000 --> 0:03:59.620000
 They don't have RJ45 jacks
 anywhere on them.

0:03:59.620000 --> 0:04:01.500000
 I can't plug a cable into them.

0:04:01.500000 --> 0:04:05.080000
 I can plug in a power cable, but
 I can't plug in a network cable.

0:04:05.080000 --> 0:04:09.400000
 So the only way I can connect to a
 network on those devices is through

0:04:09.400000 --> 0:04:13.920000
 an internal nitcard that you can't see
 that's doing Wi-Fi, that's doing

0:04:13.920000 --> 0:04:15.560000
 radio frequencies.

0:04:15.560000 --> 0:04:18.780000
 Instead of sending electrical energy across
 a cable, it's sending it through

0:04:18.780000 --> 0:04:22.520000
 the air. It's using
 a Wi-Fi protocol.

0:04:22.520000 --> 0:04:26.580000
 Now so if I was to draw that, now this
 session here is all about wired

0:04:26.580000 --> 0:04:32.400000
 networking, but you can see
 these days are wireless.

0:04:32.400000 --> 0:04:34.340000
 So let's just put that in here.

0:04:34.340000 --> 0:04:43.760000
 Let's just say that I had a tablet,
 let's say an iPad, and the iPad does

0:04:43.760000 --> 0:04:49.900000
 Wi-Fi, so I'll just make these little marks
 here represent my Wi-Fi connection.

0:04:49.900000 --> 0:04:55.280000
 So that's because the iPad, the smartphone
 has a radio inside of it, just

0:04:55.280000 --> 0:04:58.020000
 like your car has a radio inside of
 it that's using electrical energy

0:04:58.020000 --> 0:05:03.180000
 to do Wi-Fi. Now your car radio
 can only receive, right?

0:05:03.180000 --> 0:05:06.100000
 You can't use your car radio
 to transmit anything out.

0:05:06.100000 --> 0:05:09.820000
 All it can do is receive various music
 and news talk stations and stuff

0:05:09.820000 --> 0:05:13.780000
 like that. But the radio inside of your
 iPad, inside of your cell phone

0:05:13.780000 --> 0:05:17.400000
 is capable of receiving
 and transmitting.

0:05:17.400000 --> 0:05:21.720000
 So we need something at the other end
 that's listening to your radio waves

0:05:21.720000 --> 0:05:24.200000
 and it's transmitting
 radio waves to you.

0:05:24.200000 --> 0:05:29.360000
 And that device, I'll just draw that
 here, I don't have this in my rack,

0:05:29.360000 --> 0:05:33.740000
 but that device is called
 a Wi-Fi access point.

0:05:33.740000 --> 0:05:40.140000
 So I'll say Wi-Fi AP.

0:05:40.140000 --> 0:05:47.700000
 It's providing you access, it's providing
 access to your Wi-Fi devices.

0:05:47.700000 --> 0:05:52.460000
 And so this here represents my antennas
 that are on this thing which are

0:05:52.460000 --> 0:05:55.400000
 listening for the Wi-Fi
 signals from my hosts.

0:05:55.400000 --> 0:06:00.620000
 And the Wi-Fi access point in turn would
 have a wired ethernet connection

0:06:00.620000 --> 0:06:05.200000
 back to most likely a switch.

0:06:05.200000 --> 0:06:12.280000
 So for example, in your home network,
 you're probably doing Wi-Fi.

0:06:12.280000 --> 0:06:18.020000
 You've probably got some Lynxis
 or Netgear Wi-Fi access point.

0:06:18.020000 --> 0:06:21.740000
 So that's talking to your iPad, that's
 talking to your smartphone, the

0:06:21.740000 --> 0:06:25.940000
 Wi-Fi signals. And then that wireless
 access point most likely has a wired

0:06:25.940000 --> 0:06:30.060000
 connection back to, it might be connecting
 back to your cable modem or

0:06:30.060000 --> 0:06:33.260000
 your DSL modem. Or if you have a little
 bit more of an advanced network,

0:06:33.260000 --> 0:06:36.880000
 maybe it's connecting back
 to a router or a switch.

0:06:36.880000 --> 0:06:41.180000
 But the Wi-Fi access point itself has
 to have a cable to connect it into

0:06:41.180000 --> 0:06:45.620000
 the network. Now I don't have that
 my topology here, but I just wanted

0:06:45.620000 --> 0:06:51.740000
 to show you how that would fit in
 to this whole kind of thing here.

0:06:51.740000 --> 0:06:55.640000
 So in my particular case, on
 my laptop, I've got both.

0:06:55.640000 --> 0:07:01.500000
 I've got a Wi-Fi radio inside of it,
 got a Wi-Fi NIC, and I have a wired

0:07:01.500000 --> 0:07:05.000000
 NIC. But this show is about
 wired networking.

0:07:05.000000 --> 0:07:10.200000
 So I'm going to use the RJ45 port on
 the side of my laptop, and I'm going

0:07:10.200000 --> 0:07:16.140000
 to connect it via ethernet because
 that RJ45 port on my laptop speaks

0:07:16.140000 --> 0:07:19.200000
 ethernet. It understands ethernet.


0:07:19.200000 --> 0:07:23.120000
 And ethernet as a protocol says, OK, use
 this kind of electrical signaling.

0:07:23.120000 --> 0:07:25.040000
 Send it for this long.

0:07:25.040000 --> 0:07:26.560000
 Here's when you can talk.

0:07:26.560000 --> 0:07:28.280000
 Here's when you have to be quiet.

0:07:28.280000 --> 0:07:32.800000
 All that is built into the rules of ethernet,
 which my NIC card understands

0:07:32.800000 --> 0:07:34.740000
 because it does ethernet.

0:07:34.740000 --> 0:07:38.680000
 Once I have a connection of all the devices
 with a console from the octal,

0:07:38.680000 --> 0:07:43.760000
 all right, so that's these green
 connections right here.

0:07:43.760000 --> 0:07:48.460000
 Is it only one way to connect later
 on, or can I connect Telnet to all

0:07:48.460000 --> 0:07:51.120000
 those devices? OK.

0:07:51.120000 --> 0:07:58.100000
 So these green connections here
 are not for sending IP packets.

0:07:58.100000 --> 0:07:59.760000
 So there's no IP packets here.

0:07:59.760000 --> 0:08:05.620000
 When I actually connect to the terminal
 server and I start typing in commands,

0:08:05.620000 --> 0:08:09.080000
 that terminal server, what happens
 when you type in your keyboard?

0:08:09.080000 --> 0:08:11.160000
 Let's forget about networking
 for a second.

0:08:11.160000 --> 0:08:15.140000
 When you type A on your keyboard or
 two on your keyboard, what's really

0:08:15.140000 --> 0:08:20.260000
 happening? Well, that key that you're
 pressing is generating an electrical

0:08:20.260000 --> 0:08:24.840000
 signal, right? It's creating some sort
 of electrical current which represents

0:08:24.840000 --> 0:08:28.320000
 the letter C or represents the
 number one or something.

0:08:28.320000 --> 0:08:32.660000
 So there's different electrical signals
 that represent these letters and

0:08:32.660000 --> 0:08:34.600000
 these numbers on our keyboards.

0:08:34.600000 --> 0:08:40.160000
 So when I'm in the terminal server and
 when I'm typing in a command, it's

0:08:40.160000 --> 0:08:43.700000
 taking those electrical signals of
 the AI pressed or the one I pressed

0:08:43.700000 --> 0:08:48.120000
 and sending over these green lines
 into the console port of the router

0:08:48.120000 --> 0:08:53.400000
 or the switch. These are not wrapped
 in IP packets because remember, what

0:08:53.400000 --> 0:08:54.660000
 is an IP packet?

0:08:54.660000 --> 0:08:58.480000
 An IP packet has some data behind it,
 maybe the same type of electrical

0:08:58.480000 --> 0:09:02.780000
 signals, maybe in the data portion
 of an IP packet is in the letter A,

0:09:02.780000 --> 0:09:09.300000
 the number one, the letter B, but that
 IP packet is IP because at the

0:09:09.300000 --> 0:09:12.060000
 front of it, it has an address.

0:09:12.060000 --> 0:09:15.360000
 It has an address of the IP address
 of my laptop where it's coming from

0:09:15.360000 --> 0:09:20.000000
 and an address, a destination address
 of where it's going through.

0:09:20.000000 --> 0:09:24.360000
 So that thing can travel through a network
 and get to the correct destination.

0:09:24.360000 --> 0:09:26.320000
 There's no addresses here.

0:09:26.320000 --> 0:09:29.660000
 Everything I'm sending across these
 green octal cables is just strictly

0:09:29.660000 --> 0:09:31.500000
 letters and numbers.

0:09:31.500000 --> 0:09:33.260000
 There's no IP at all.

0:09:33.260000 --> 0:09:37.000000
 So I cannot use these
 for IP connections.

0:09:37.000000 --> 0:09:41.500000
 Tell me is a particular protocol where
 I can take these letters and numbers

0:09:41.500000 --> 0:09:46.680000
 I'm typing on my keyboard and wrap
 it inside of an IP header.

0:09:46.680000 --> 0:09:51.660000
 So instead of needing to connect to the
 console port, I can send IP packets

0:09:51.660000 --> 0:09:54.180000
 to a router or a switch.

0:09:54.180000 --> 0:09:57.560000
 And when the router switch gets the
 IP packages, oh, here comes an IP

0:09:57.560000 --> 0:10:00.480000
 packet. Oh, it's got my name
 on it, my IP address.

0:10:00.480000 --> 0:10:04.100000
 This is for me. And then when it looks
 in the body, the packet says, oh,

0:10:04.100000 --> 0:10:06.660000
 the body of the packet
 is carrying telnet.

0:10:06.660000 --> 0:10:07.740000
 Oh, what's telnet?

0:10:07.740000 --> 0:10:10.740000
 Telnet says, someone's trying to talk
 to me, they're trying to get into

0:10:10.740000 --> 0:10:14.280000
 my brain and configure me
 and send commands to me.

0:10:14.280000 --> 0:10:18.380000
 That's what telnet is used for, to send
 commands from one device to another.

0:10:18.380000 --> 0:10:23.060000
 We can't do that over the octal cables
 because telnet relies on the IP

0:10:23.060000 --> 0:10:27.320000
 protocol. And all the communications
 across these green lines here, it's

0:10:27.320000 --> 0:10:29.500000
 not doing IP whatsoever.

0:10:29.500000 --> 0:10:32.920000
 So in order to do telnet, once again,
 I would need to put some sort of

0:10:32.920000 --> 0:10:37.940000
 IP address on one or more of the interfaces
 on these devices so I could

0:10:37.940000 --> 0:10:42.460000
 send my telnet packets inside
 of IP to get to them.

0:10:42.460000 --> 0:10:46.280000
 At that point, I wouldn't necessarily
 need the octal cables anymore.

0:10:46.280000 --> 0:10:49.840000
 Once I've got IP and all these devices
 and I can telnet to the devices

0:10:49.840000 --> 0:10:52.920000
 over Ethernet, I can remove
 my terminal server.

0:10:52.920000 --> 0:10:55.680000
 I won't need anymore to get
 access to the command line.

0:10:55.680000 --> 0:10:59.740000
 So the terminal server was initially
 just needed because there was no

0:10:59.740000 --> 0:11:01.540000
 IP on any of these devices.

0:11:01.540000 --> 0:11:07.120000
 So the only way I could get to them
 was by connecting to their console

0:11:07.120000 --> 0:11:09.440000
 ports. That's why I needed it.

0:11:09.440000 --> 0:11:13.160000
 So an octal cable is all a physical layer
 thing because there's no addressing.

0:11:13.160000 --> 0:11:15.580000
 There's no MAC addresses
 and no IP addresses.

0:11:15.580000 --> 0:11:18.340000
 It all resides at the physical
 layer of the OSI model.

0:11:18.340000 --> 0:11:21.660000
 That's where you would find it.

0:11:21.660000 --> 0:11:29.160000
 When I was in my terminal server, so here
 I am, when I went into a connection,

0:11:29.160000 --> 0:11:33.620000
 for example, switch one, and I issued
 some sort of a keyboard shortcut

0:11:33.620000 --> 0:11:36.380000
 which got me back here
 to the terminal server.

0:11:36.380000 --> 0:11:40.320000
 What is that keyboard shortcut
 I'm using to go back and forth?

0:11:40.320000 --> 0:11:44.280000
 So this is a common Cisco
 keyboard shortcut.

0:11:44.280000 --> 0:11:47.000000
 It is Control Shift 6.

0:11:47.000000 --> 0:11:50.460000
 So on my keyboard, I'm hitting all
 three keys at the same time.

0:11:50.460000 --> 0:11:55.960000
 Control Shift 6, all at the same
 time, I let go and I hit X.

0:11:55.960000 --> 0:12:01.320000
 Control Shift 6, let go and hit
 X within like a second or less.

0:12:01.320000 --> 0:12:03.720000
 So here I am in session three.

0:12:03.720000 --> 0:12:06.760000
 Control Shift 6, let go, hit X.

0:12:06.760000 --> 0:12:09.000000
 And it gets me back there.

0:12:09.000000 --> 0:12:10.880000
 Very useful to know.

0:12:10.880000 --> 0:12:15.420000
 All right, so building up my topology
 here, I know I now have to connect

0:12:15.420000 --> 0:12:17.460000
 these physical interfaces here.

0:12:17.460000 --> 0:12:20.380000
 Well, for example, let's take
 a look at switch one.

0:12:20.380000 --> 0:12:22.160000
 Here's switch one.

0:12:22.160000 --> 0:12:24.140000
 That's the one here on the bottom.


0:12:24.140000 --> 0:12:27.780000
 And my laptop is over here.

0:12:27.780000 --> 0:12:29.500000
 So I'm going to have
 to connect here.

0:12:29.500000 --> 0:12:34.420000
 And so my first choice I have to make
 is what interface do I want to select

0:12:34.420000 --> 0:12:40.320000
 on switch one? I could select any interface,
 but to me, I want to select

0:12:40.320000 --> 0:12:41.760000
 an interface I can
 easily remember.

0:12:41.760000 --> 0:12:46.940000
 If I just randomly plug this into interface,
 you know, 13 or 21 or something,

0:12:46.940000 --> 0:12:50.000000
 by the time I get done cabling this whole
 thing, I'm not going to remember

0:12:50.000000 --> 0:12:53.740000
 that stuff. So just to make it simple,
 I'm going to plug it into interface

0:12:53.740000 --> 0:12:59.220000
 number one. So I'll
 write that up here.

0:12:59.220000 --> 0:13:04.640000
 And the switch interfaces are numbered
 as zero slash and a number.

0:13:04.640000 --> 0:13:07.740000
 So this will be zero slash one.

0:13:07.740000 --> 0:13:12.780000
 And then I'll use the last interface
 to connect one switch to another.

0:13:12.780000 --> 0:13:17.220000
 So I'll do zero slash
 24 to zero slash 24.

0:13:17.220000 --> 0:13:20.180000
 So that'll help me remember the first
 interface goes to the laptop.

0:13:20.180000 --> 0:13:23.000000
 Last interface connects the
 switch to another switch.

0:13:23.000000 --> 0:13:25.260000
 And I'll repeat it right
 here on switch two.

0:13:25.260000 --> 0:13:30.800000
 I'll use his first interface to connect
 to the router and router one,

0:13:30.800000 --> 0:13:35.260000
 which is this top guy right here.

0:13:35.260000 --> 0:13:39.200000
 If I zoom in on this, it'll
 kind of blur out.

0:13:39.200000 --> 0:13:41.280000
 Well, no, maybe we can see it.

0:13:41.280000 --> 0:13:44.820000
 I don't know if you can see that, but
 here's the two ethernet interfaces

0:13:44.820000 --> 0:13:52.620000
 that it has. These
 are the two ethers.

0:13:52.620000 --> 0:13:55.000000
 So I can select one of these.

0:13:55.000000 --> 0:13:58.720000
 One is labeled fast, ethernet
 zero slash zero.

0:13:58.720000 --> 0:14:02.260000
 The other is zero slash one.

0:14:02.260000 --> 0:14:04.360000
 So why don't I do this?

0:14:04.360000 --> 0:14:06.860000
 Since all over here, I've already
 got zero slash one.

0:14:06.860000 --> 0:14:10.600000
 Why don't I keep it consistent and have
 it go into zero slash one right

0:14:10.600000 --> 0:14:14.920000
 here as well? So let me go now.

0:14:14.920000 --> 0:14:18.260000
 Okay, so I know what
 interfaces I want.

0:14:18.260000 --> 0:14:21.540000
 And I know, let me
 go back to this.

0:14:21.540000 --> 0:14:25.980000
 Make this a little bit larger
 so you can see it.

0:14:25.980000 --> 0:14:29.900000
 There we go. And I know that now I'm
 going to have to choose an ethernet

0:14:29.900000 --> 0:14:32.280000
 cable. I got a black one.

0:14:32.280000 --> 0:14:33.580000
 I got a red one.

0:14:33.580000 --> 0:14:36.960000
 I got a pink one and I got a
 big orange one right there.

0:14:36.960000 --> 0:14:38.800000
 So which one is appropriate?

0:14:38.800000 --> 0:14:42.880000
 What makes them different other than
 their color or are they different?

0:14:42.880000 --> 0:14:43.880000
 They are different.

0:14:43.880000 --> 0:14:45.660000
 Here's something else
 you need to know.

0:14:45.660000 --> 0:14:51.260000
 If I was to hold up these RJ45 jacks
 in front of my face real closely,

0:14:51.260000 --> 0:14:57.960000
 I would see in this where is it?

0:14:57.960000 --> 0:15:04.900000
 This one. There we go.

0:15:04.900000 --> 0:15:09.360000
 We would see that inside the RJ45
 jacket has these colored cables.

0:15:09.360000 --> 0:15:12.660000
 Now it might not necessarily be brown
 and green and blue like this, but

0:15:12.660000 --> 0:15:20.820000
 each individual wire is wrapped in a
 colored plastic or rubber coating.

0:15:20.820000 --> 0:15:30.200000
 And why this is important is because
 some of my cables, for example, I

0:15:30.200000 --> 0:15:33.160000
 just make this a little bit
 bigger, look like this.

0:15:33.160000 --> 0:15:38.940000
 I don't know if you can tell that, but
 if you can look at this here, you

0:15:38.940000 --> 0:15:45.680000
 can see that, for example, wire number
 two, which is right here, is sort

0:15:45.680000 --> 0:15:47.780000
 of an orange-ish brown color.

0:15:47.780000 --> 0:15:53.040000
 And at the other end of the cable, also
 wire number two is the same color.

0:15:53.040000 --> 0:15:56.320000
 It looks like right here that wire
 number, I can't really read it very

0:15:56.320000 --> 0:15:59.920000
 easily, but it looks like maybe
 wire number six is green.

0:15:59.920000 --> 0:16:03.580000
 And over here, wire
 number six is green.

0:16:03.580000 --> 0:16:10.080000
 So if I take my cables, for example,
 this one right here, and if I held

0:16:10.080000 --> 0:16:14.440000
 it up and I looked at the colors, I
 would see that the colors and the

0:16:14.440000 --> 0:16:18.940000
 order of the colors from left to right
 on this connector is exactly the

0:16:18.940000 --> 0:16:21.240000
 same as this connector.

0:16:21.240000 --> 0:16:24.700000
 I call that a straight
-through cable.

0:16:24.700000 --> 0:16:29.460000
 As opposed to or as compared to, if I
 take a look at this red cable right

0:16:29.460000 --> 0:16:33.220000
 here and I do the same thing, I hold
 the connectors up and I take a look

0:16:33.220000 --> 0:16:38.440000
 at that, that one is going
 to look like this.

0:16:38.440000 --> 0:16:39.620000
 Notice the difference here.

0:16:39.620000 --> 0:16:46.200000
 In this particular case, wire number
 one on one side, which is green and

0:16:46.200000 --> 0:16:51.140000
 white, goes to wire number
 three on the other side.

0:16:51.140000 --> 0:16:55.140000
 And wire number two, which is just
 a solid green, goes to wire number

0:16:55.140000 --> 0:16:57.660000
 six on the other side.

0:16:57.660000 --> 0:17:03.180000
 We call this, as it says,
 a crossover cable.

0:17:03.180000 --> 0:17:11.480000
 And a crossover cable, one on one side
 goes to three on the other, two

0:17:11.480000 --> 0:17:15.520000
 on one side goes to
 six on the other.

0:17:15.520000 --> 0:17:19.440000
 For example, look at
 this one right here.

0:17:19.440000 --> 0:17:23.200000
 Wire number two, which is sort of an
 orange-ish brown color, goes to wire

0:17:23.200000 --> 0:17:25.980000
 number six right here.

0:17:25.980000 --> 0:17:28.380000
 Two to six, one to three.

0:17:28.380000 --> 0:17:30.580000
 So that's a crossover cable.

0:17:30.580000 --> 0:17:36.360000
 So you can see that even though they
 look the same, once I actually look

0:17:36.360000 --> 0:17:38.820000
 at the wiring on the inside,
 they're not the same.

0:17:38.820000 --> 0:17:42.420000
 Some are straight through,
 some are crossover.

0:17:42.420000 --> 0:17:49.020000
 What does that have to
 do with my picture?

0:17:49.020000 --> 0:17:53.220000
 When you are connecting devices that
 are similar to each other, like a

0:17:53.220000 --> 0:17:58.020000
 switch to a switch, or if I was connecting
 an ethernet cable from one

0:17:58.020000 --> 0:17:59.860000
 router to another router.

0:17:59.860000 --> 0:18:02.020000
 So devices are similar.

0:18:02.020000 --> 0:18:05.020000
 That requires a crossover cable.

0:18:05.020000 --> 0:18:07.320000
 So I'll put that right here.

0:18:07.320000 --> 0:18:10.020000
 So I'm going to need
 a crossover for this.

0:18:10.020000 --> 0:18:15.380000
 When you're connecting devices that
 are dissimilar, that are unlike, we

0:18:15.380000 --> 0:18:17.340000
 use a straight through cable.

0:18:17.340000 --> 0:18:23.480000
 So most of my connections here are going
 to be straight through cables.

0:18:23.480000 --> 0:18:30.240000
 So this will be straight through
 this down here, switch to router.

0:18:30.240000 --> 0:18:34.480000
 It will be straight through
 serial cables.

0:18:34.480000 --> 0:18:35.600000
 You don't have to
 worry about that.

0:18:35.600000 --> 0:18:39.420000
 That this crossover in ethernet
 is only an ethernet.

0:18:39.420000 --> 0:18:42.820000
 Crossover in straight through
 is only an ethernet thing.

0:18:42.820000 --> 0:18:45.560000
 It does not apply to other
 types of cables.

0:18:45.560000 --> 0:18:48.700000
 Router to switch, those are different
 types of devices, so that will be

0:18:48.700000 --> 0:18:50.140000
 a straight through.

0:18:50.140000 --> 0:18:52.280000
 And once again, switch to router.

0:18:52.280000 --> 0:18:54.140000
 That will be a straight through.

0:18:54.140000 --> 0:19:01.800000
 All right, so let me connect up building
 number one here for a second.

0:19:01.800000 --> 0:19:07.100000
 So my laptop, I'm going to need a fairly
 long, straight through ethernet

0:19:07.100000 --> 0:19:14.100000
 cable. And I think this pink one
 right here will do it for me.

0:19:14.100000 --> 0:19:16.540000
 It's fairly long.

0:19:16.540000 --> 0:19:19.420000
 And of course, if I was doing this
 in a real network, I'd want to make

0:19:19.420000 --> 0:19:23.780000
 this nice and pretty and organized
 and use zip ties and cable ties and

0:19:23.780000 --> 0:19:26.680000
 everything, but I'm just doing
 this from scratch here.

0:19:26.680000 --> 0:19:28.200000
 So I'm just going to look at this.


0:19:28.200000 --> 0:19:32.440000
 The lighting in this room isn't the
 best, but I'm pretty sure of that

0:19:32.440000 --> 0:19:35.500000
 looking at the ends of this, this
 is a straight through cable.

0:19:35.500000 --> 0:19:41.460000
 So I'm going to connect one end of
 it to the RG45 jack on my laptop.

0:19:41.460000 --> 0:19:47.700000
 There we go. And connect the other end
 of it to a quarter of my diagram

0:19:47.700000 --> 0:19:50.480000
 port zero slash one
 and switch one.

0:19:50.480000 --> 0:19:53.660000
 All right, there we go.

0:19:53.660000 --> 0:19:56.820000
 Okay, so it is connected in.

0:19:56.820000 --> 0:20:05.640000
 Now what I'm doing here is my next step
 is usually a switch port, a port

0:20:05.640000 --> 0:20:08.380000
 on a switch, when you plug in a cable and
 that cable is plugged into something

0:20:08.380000 --> 0:20:12.240000
 else, instantly comes up and you should
 start seeing some lights flashing

0:20:12.240000 --> 0:20:13.320000
 on that interface.

0:20:13.320000 --> 0:20:15.400000
 And I'm not seeing that.

0:20:15.400000 --> 0:20:18.560000
 And I know I did this test yesterday
 and the lights did flash.

0:20:18.560000 --> 0:20:21.200000
 So I'm pretty sure this
 cable is messed up.

0:20:21.200000 --> 0:20:23.900000
 So let's just get rid of this
 cable and use a different one.

0:20:23.900000 --> 0:20:27.820000
 If I get the same type of behavior with
 a different cable where there's

0:20:27.820000 --> 0:20:32.320000
 no lights on my laptop and there's
 no lights on the switch interface,

0:20:32.320000 --> 0:20:36.560000
 then I'll have to do some additional
 troubleshooting.

0:20:36.560000 --> 0:20:37.880000
 So let's see here.

0:20:37.880000 --> 0:20:39.960000
 I got a nice big orange
 cable here.

0:20:39.960000 --> 0:20:44.460000
 I'm pretty sure this is a
 straight through cable.

0:20:44.460000 --> 0:20:53.000000
 So let's go ahead and try using this
 guy and see if I get better results.

0:20:53.000000 --> 0:21:00.800000
 And in reality, you know, your switch
 probably is located 20, 50, 100

0:21:00.800000 --> 0:21:03.260000
 feet away from your laptops.

0:21:03.260000 --> 0:21:07.560000
 Just depends on where the laptop is located,
 where's the cube in relationship

0:21:07.560000 --> 0:21:10.360000
 to where it is located.

0:21:10.360000 --> 0:21:14.960000
 So you probably will have to have quite
 a long cable to connect them.

0:21:14.960000 --> 0:21:23.160000
 All right. So I am still
 not getting anything.

0:21:23.160000 --> 0:21:25.180000
 So now troubleshooting.

0:21:25.180000 --> 0:21:28.900000
 Highly unlikely that
 both cables are bad.

0:21:28.900000 --> 0:21:32.860000
 So the next thing that would go through
 my mind is, well, either my Ethernet

0:21:32.860000 --> 0:21:34.880000
 net card has been disabled.

0:21:34.880000 --> 0:21:36.940000
 I don't think I did that.

0:21:36.940000 --> 0:21:40.860000
 Or the interface on
 the switch is down.

0:21:40.860000 --> 0:21:42.200000
 It's not working right now.

0:21:42.200000 --> 0:21:46.120000
 So let me use my terminal server and
 get into the command line of switch

0:21:46.120000 --> 0:21:48.760000
 number one and take a look.

0:21:48.760000 --> 0:21:54.980000
 And by the way, some Cisco routers and
 switches have interfaces that can

0:21:54.980000 --> 0:21:57.940000
 auto detect the cable.

0:21:57.940000 --> 0:22:01.420000
 In other words, you know, some switches,
 if I had two switches together

0:22:01.420000 --> 0:22:04.460000
 and I connected to straight through
 cable, nothing would happen.

0:22:04.460000 --> 0:22:05.600000
 It just wouldn't work.

0:22:05.600000 --> 0:22:07.780000
 But if they have these types of interfaces,
 and I think they're called

0:22:07.780000 --> 0:22:14.100000
 MDIX, I'm not sure what that stands for,
 Mary David Igloo X-ray, but MDIX

0:22:14.100000 --> 0:22:17.580000
 is an ability to auto
 detect the cable type.

0:22:17.580000 --> 0:22:21.020000
 So whether you have a straight through
 or a crossover, it'll automatically

0:22:21.020000 --> 0:22:23.360000
 detect that and account for it.

0:22:23.360000 --> 0:22:25.360000
 I don't think these interfaces
 do that though.

0:22:25.360000 --> 0:22:29.280000
 MDIX stands for medium dependent
 interface crossover.

