WEBVTT

0:00:08.040000 --> 0:00:12.060000
 Okay, so IPv6 IP tunnels.

0:00:12.060000 --> 0:00:18.420000
 Now there are subtypes of this that
 we'll see in the next lessons coming

0:00:18.420000 --> 0:00:25.980000
 up. But this is just straight point
-to-point manual IPv6 IP tunnel.

0:00:25.980000 --> 0:00:30.020000
 We're going to use the same topology
 we used in our last lesson.

0:00:30.020000 --> 0:00:35.200000
 So as a reminder, we have a tunnel between
 R1 and R4 that's already built.

0:00:35.200000 --> 0:00:37.140000
 We're not going to rebuild that.

0:00:37.140000 --> 0:00:41.720000
 We're already running EIGRP across it
 and we're already exchanging routes.

0:00:41.720000 --> 0:00:45.880000
 So just to follow up with this, we'll
 switch over to the command line.

0:00:45.880000 --> 0:00:46.920000
 Here's our tunnel.

0:00:46.920000 --> 0:00:55.920000
 Okay, and it's currently running
 protocol transport GRE IP.

0:00:55.920000 --> 0:01:01.480000
 And again, this will be very, very
 short because now all we do is say

0:01:01.480000 --> 0:01:22.500000
 tunnel mode IPv6 IP on both sides.


0:01:22.500000 --> 0:01:29.060000
 And what this is going to do is tunnel
 goes down and it comes right back

0:01:29.060000 --> 0:01:33.260000
 up. What this did is get
 rid of the GRE header.

0:01:33.260000 --> 0:01:45.320000
 Okay, so if we look at our tunnel again,
 okay, first off, where this said

0:01:45.320000 --> 0:01:54.780000
 total protocol transport is GRE, tunnel
 protocol transport is now IPv6

0:01:54.780000 --> 0:02:02.900000
 over IP. So what this just did is this
 just limited us to only being able

0:02:02.900000 --> 0:02:09.100000
 to carry IPv6. That's all, okay.

0:02:09.100000 --> 0:02:15.740000
 What it buys us is number one, the
 ability to run some of our upcoming

0:02:15.740000 --> 0:02:18.900000
 tunneling options that we're
 going to take a look at.

0:02:18.900000 --> 0:02:20.380000
 That's one thing.

0:02:20.380000 --> 0:02:29.060000
 The other thing it does for us is allows
 us to save a, what's, I mean,

0:02:29.060000 --> 0:02:35.220000
 it's not like it's a ton, but
 1476 was our MTU up here.

0:02:35.220000 --> 0:02:37.420000
 And now our MTU is 1480.

0:02:37.420000 --> 0:02:42.440000
 So we're saving four bytes
 on the GRE header.

0:02:42.440000 --> 0:02:44.780000
 So it's not really a huge deal.

0:02:44.780000 --> 0:02:51.180000
 Honestly, the biggest reason to go
 to IPv6 IP is to enable some of the

0:02:51.180000 --> 0:02:56.980000
 dynamic tunnels that we're going to
 take a look at NACs such as the six

0:02:56.980000 --> 0:03:02.040000
 to four tunnels and the ICITAP tunnels,
 which are going to take a little

0:03:02.040000 --> 0:03:04.520000
 bit more of building.

0:03:04.520000 --> 0:03:11.140000
 So what we're going to do for those
 is we're actually going to do some

0:03:11.140000 --> 0:03:16.940000
 static routes and then we're going
 to also redo our tunnel when we get

0:03:16.940000 --> 0:03:18.340000
 to that section.

0:03:18.340000 --> 0:03:23.660000
 But that's really it to
 go from GRE to IPv6 IP.

0:03:23.660000 --> 0:03:25.820000
 It's literally just typing
 in that one command.

0:03:25.820000 --> 0:03:29.000000
 You save four bytes of overhead.

0:03:29.000000 --> 0:03:33.200000
 But more importantly, we need to do this
 as we move into our next options.

