WEBVTT

0:00:03.040000 --> 0:00:08.540000
 Hello and welcome to this video
 titled Cisco Access Point Modes.

0:00:08.540000 --> 0:00:11.600000
 In this video I'm going to talk about
 an introduction to what the various

0:00:11.600000 --> 0:00:14.420000
 modes are the Cisco Access
 Point could operate in.

0:00:14.420000 --> 0:00:18.380000
 We're going to talk about local and
 bridged modes, flex connect mode,

0:00:18.380000 --> 0:00:26.860000
 monitor mode, sniffer mode,
 sensor mode, and mesh mode.

0:00:26.860000 --> 0:00:31.000000
 So Cisco Access Points can operate
 in several of different modes.

0:00:31.000000 --> 0:00:35.240000
 We know that an autonomous access point
 is something all by itself, right?

0:00:35.240000 --> 0:00:40.840000
 That's a mode that is not really a configurable
 mode when you buy an access

0:00:40.840000 --> 0:00:44.560000
 point. If it's an autonomous access
 point, typically that's what it is

0:00:44.560000 --> 0:00:46.680000
 unless you upgrade
 it with software.

0:00:46.680000 --> 0:00:49.800000
 So with an autonomous access point,
 we wouldn't really consider that a

0:00:49.800000 --> 0:00:53.240000
 mode. What we're talking about here
 are access points that are managed

0:00:53.240000 --> 0:00:55.120000
 by a controller.

0:00:55.120000 --> 0:00:57.880000
 So an access point that's managed by a
 controller, we call it a lightweight

0:00:57.880000 --> 0:01:02.040000
 access point, but it can operate
 in several different modes.

0:01:02.040000 --> 0:01:05.080000
 And that's something you would configure
 on the controller and push it

0:01:05.080000 --> 0:01:07.200000
 down to the access point.

0:01:07.200000 --> 0:01:08.880000
 So what these modes do?

0:01:08.880000 --> 0:01:12.440000
 Well, these modes of operation determine
 such things as is the access

0:01:12.440000 --> 0:01:14.780000
 point associated with
 a controller or not?

0:01:14.780000 --> 0:01:19.580000
 Can the access point accept Wi
-Fi connections from clients?

0:01:19.580000 --> 0:01:24.080000
 How will the access point switch
 frames from the clients?

0:01:24.080000 --> 0:01:29.040000
 Can the access point report on RF conditions
 capture Wi-Fi traffic and

0:01:29.040000 --> 0:01:32.480000
 act as a sniffer or detect
 rogue access points?

0:01:32.480000 --> 0:01:36.200000
 So let's look at what some of these
 various modes are as we go through

0:01:36.200000 --> 0:01:41.160000
 them. So let's start with
 local and bridged modes.

0:01:41.160000 --> 0:01:45.460000
 So local mode, this is your default
 mode for a lightweight access point.

0:01:45.460000 --> 0:01:49.240000
 So this is when the access point
 is connected to a controller.

0:01:49.240000 --> 0:01:53.380000
 The controller is basically controlling
 and managing that access point.

0:01:53.380000 --> 0:01:56.600000
 So it's going to create a couple of
 CAPWAP tunnels to that controller,

0:01:56.600000 --> 0:02:01.340000
 a data tunnel and a control
 tunnel, all within CAPWAP.

0:02:01.340000 --> 0:02:06.060000
 And in local mode, if that CAPWAP tunnel
 fails due to like a WAN failure

0:02:06.060000 --> 0:02:10.200000
 or a routing failure or something else,
 that access point is going to

0:02:10.200000 --> 0:02:14.480000
 have to disconnect all of its wireless
 LAN clients and find another available

0:02:14.480000 --> 0:02:20.640000
 controller. So in local mode, an access
 point can't operate if it's not

0:02:20.640000 --> 0:02:23.600000
 talking to and connected
 to a controller.

0:02:23.600000 --> 0:02:26.220000
 It can't operate independently.

0:02:26.220000 --> 0:02:28.940000
 Now there's another mode you're probably
 not going to see very often.

0:02:28.940000 --> 0:02:32.460000
 You're probably not going to use a
 lot, which is called bridge mode.

0:02:32.460000 --> 0:02:34.140000
 Let's discuss that real briefly.

0:02:34.140000 --> 0:02:42.700000
 So bridge mode, this allows an autonomous
 access point to act as a client,

0:02:42.700000 --> 0:02:47.960000
 as a wireless LAN client, and associate
 to a local, or I should say a

0:02:47.960000 --> 0:02:50.020000
 lightweight access point.

0:02:50.020000 --> 0:02:52.140000
 So why would we do this?

0:02:52.140000 --> 0:02:54.780000
 Well, this would be one of these one
-off situations where you might have

0:02:54.780000 --> 0:02:56.540000
 some wired clients.

0:02:56.540000 --> 0:02:59.140000
 For example, maybe a wired
 network printer.

0:02:59.140000 --> 0:03:02.140000
 So a printer that's got an Ethernet
 cable, but doesn't actually have any

0:03:02.140000 --> 0:03:04.740000
 WiFi NIC inside of it.

0:03:04.740000 --> 0:03:09.420000
 And we want to give
 that access to WiFi.

0:03:09.420000 --> 0:03:13.160000
 So in other words, wired clients can
 connect to the Ethernet port on the

0:03:13.160000 --> 0:03:17.540000
 back of the autonomous AP and have their
 traffic bridged across the wireless

0:03:17.540000 --> 0:03:20.760000
 LAN to gain access to the
 distribution system.

0:03:20.760000 --> 0:03:24.040000
 So let's just draw that out real quickly
 to see what that looks like.

0:03:24.040000 --> 0:03:32.220000
 So let's say right here we have
 a wired network printer.

0:03:32.220000 --> 0:03:35.880000
 He's got no WiFi capabilities.

0:03:35.880000 --> 0:03:41.680000
 All right, over here we have a client
 that wants to talk to that printer.

0:03:41.680000 --> 0:03:44.520000
 But here's our problem.

0:03:44.520000 --> 0:03:53.920000
 This client is connected
 to a switch.

0:03:53.920000 --> 0:04:00.880000
 And eventually we get to the point
 where maybe here's a controller.

0:04:00.880000 --> 0:04:08.960000
 A wireless controller is
 connected to that switch.

0:04:08.960000 --> 0:04:14.380000
 And then we get down here and then
 here we have our lightweight access

0:04:14.380000 --> 0:04:21.380000
 point. So that wired printer can't physically
 be connected to that laptop

0:04:21.380000 --> 0:04:22.860000
 or PC on the right.

0:04:22.860000 --> 0:04:26.740000
 For whatever reason we can't move it onto
 that wired network that is physically

0:04:26.740000 --> 0:04:29.640000
 disconnected from that
 wired network.

0:04:29.640000 --> 0:04:32.140000
 Well, here's what we can do.

0:04:32.140000 --> 0:04:39.120000
 We can take an autonomous AP.

0:04:39.120000 --> 0:04:43.800000
 We know that he's got some Ethernet
 ports on the back of him.

0:04:43.800000 --> 0:04:47.860000
 So why don't we connect our Ethernet
 port on him to that wired printer?

0:04:47.860000 --> 0:04:52.980000
 And then that autonomous AP can
 associate to the lightweight AP.

0:04:52.980000 --> 0:04:57.560000
 From the lightweight AP's perspective,
 this autonomous AP is going to

0:04:57.560000 --> 0:05:02.660000
 look like a WiFi client.

0:05:02.660000 --> 0:05:06.820000
 And now data can get back and forth from
 the wired printer to our distribution

0:05:06.820000 --> 0:05:11.240000
 system over here because it's being
 bridged by the autonomous AP.

0:05:11.240000 --> 0:05:13.660000
 So really the autonomous AP
 is just acting as a bridge.

0:05:13.660000 --> 0:05:18.440000
 He's taking wired data from the printer
 and bridging it onto the WiFi

0:05:18.440000 --> 0:05:22.720000
 network to be picked up by the
 lightweight access point.

0:05:22.720000 --> 0:05:24.200000
 That's what bridge mode is.

0:05:24.200000 --> 0:05:33.920000
 So bridge mode is this autonomous AP
 right here performing that service.

0:05:33.920000 --> 0:05:39.180000
 Then we also have flex connect mode,
 also known as HREAP, which stands

0:05:39.180000 --> 0:05:44.520000
 for hybrid remote edge AP.

0:05:44.520000 --> 0:05:47.840000
 So in this case the access point is
 going to utilize the services of a

0:05:47.840000 --> 0:05:50.820000
 controller just like it would
 if it was in local mode.

0:05:50.820000 --> 0:05:52.100000
 But here's the difference.

0:05:52.100000 --> 0:05:55.440000
 First of all, this special mode has
 to be configured and supported on

0:05:55.440000 --> 0:05:57.840000
 the controller and
 the access point.

0:05:57.840000 --> 0:06:00.780000
 Not all access points
 will support this.

0:06:00.780000 --> 0:06:03.760000
 So the controller has to have this
 turned on with a switch or a button

0:06:03.760000 --> 0:06:05.500000
 or a pull down menu.

0:06:05.500000 --> 0:06:08.360000
 It has to push it down to the access
 point so the access point knows it's

0:06:08.360000 --> 0:06:09.680000
 going to do this.

0:06:09.680000 --> 0:06:13.340000
 Primarily designed for remote
 access points, right?

0:06:13.340000 --> 0:06:16.940000
 Remember hybrid remote
 edge access point.

0:06:16.940000 --> 0:06:18.620000
 So what's the benefit here?

0:06:18.620000 --> 0:06:22.840000
 It will allow the access point to locally
 bridge WiFi traffic onto the

0:06:22.840000 --> 0:06:26.900000
 wired LAN for certain SSID's.

0:06:26.900000 --> 0:06:32.500000
 So in this particular case here, the controller
 will send down via a capwap

0:06:32.500000 --> 0:06:38.520000
 tunnel and he'll tell the lab, hey,
 why don't you have a corporate SSID

0:06:38.520000 --> 0:06:46.000000
 and maybe a office SSID.

0:06:46.000000 --> 0:06:51.380000
 And the controller will say, hey, the corporate
 SSID, anybody that's associated

0:06:51.380000 --> 0:07:00.020000
 to that has to send their data
 across the capwap tunnel.

0:07:00.020000 --> 0:07:07.740000
 Anybody that's associated to the office
 SSID, that data can be bridged

0:07:07.740000 --> 0:07:16.020000
 onto the local LAN.

0:07:16.020000 --> 0:07:18.840000
 So the idea here is that people who
 are in this office, they would be

0:07:18.840000 --> 0:07:23.520000
 told either via an email or maybe a sign
 posted on the wall, hey, if you're

0:07:23.520000 --> 0:07:28.580000
 in this branch office right here, if
 you need to access our own local

0:07:28.580000 --> 0:07:33.080000
 server, make sure you connect
 to the office SSID.

0:07:33.080000 --> 0:07:37.080000
 Once they connect to that, the lightweight
 access point can put their

0:07:37.080000 --> 0:07:39.620000
 data directly on that local LAN.

0:07:39.620000 --> 0:07:42.760000
 Anything else they need to reach
 is over at the headquarters.

0:07:42.760000 --> 0:07:46.700000
 They would disconnect or de-associate
 from the office SSID and they would

0:07:46.700000 --> 0:07:50.640000
 now need to connect to the corporate
 SSID, in which case all their data

0:07:50.640000 --> 0:07:53.740000
 now would go across the
 data capwap tunnel.

0:07:53.740000 --> 0:07:58.040000
 That's what we call flex connect mode
 and the AP has to be configured

0:07:58.040000 --> 0:08:00.760000
 to operate in that mode.

0:08:00.760000 --> 0:08:05.880000
 Now there's some other also special modes
 here you can use for diagnostics

0:08:05.880000 --> 0:08:07.800000
 and troubleshooting purposes.

0:08:07.800000 --> 0:08:12.080000
 The first of which we'll talk
 about is monitor mode.

0:08:12.080000 --> 0:08:16.560000
 Now most access points, whether they're
 Cisco or not Cisco, when they're

0:08:16.560000 --> 0:08:21.320000
 operating is just a regular access point
 in local mode, so they're connected

0:08:21.320000 --> 0:08:24.520000
 to a controller, they're
 also servicing clients.

0:08:24.520000 --> 0:08:28.700000
 That access point will be told by the
 controller, hey, you need to be

0:08:28.700000 --> 0:08:32.540000
 on channel one, or you need to be on
 channel 48 if you're in the 5GHz

0:08:32.540000 --> 0:08:37.120000
 spectrum. So that will be the channel
 that the SSID is broadcast on and

0:08:37.120000 --> 0:08:38.900000
 the clients will be
 associated to that.

0:08:38.900000 --> 0:08:45.520000
 But the access point won't be listening
 to that channel 100% of the time.

0:08:45.520000 --> 0:08:49.980000
 So in local mode, the access point will
 take tiny slices of time so when

0:08:49.980000 --> 0:08:54.180000
 no client is talking, when everything
 is idle, the access point will go

0:08:54.180000 --> 0:08:58.720000
 off that channel for, like it says here,
 very small slice, 0.2% of their

0:08:58.720000 --> 0:09:03.120000
 overall time, they'll go off that channel
 and start scanning the other

0:09:03.120000 --> 0:09:07.460000
 channels. And so while they're scanning
 the other channels they're trying

0:09:07.460000 --> 0:09:09.880000
 to detect, hey, is there
 another access point?

0:09:09.880000 --> 0:09:13.880000
 If I'm on primarily channel one, everything's
 idle right now, let me leave

0:09:13.880000 --> 0:09:18.240000
 that channel for just a few milliseconds
 in scan channel one or scan channel

0:09:18.240000 --> 0:09:21.200000
 six or channel 11 or channel 13.

0:09:21.200000 --> 0:09:26.160000
 Do I hear any other access points that
 are advertising the same SSID as

0:09:26.160000 --> 0:09:30.020000
 me? Or do I hear anything that looks
 like it could potentially be a Wi

0:09:30.020000 --> 0:09:31.700000
-Fi attack of some sort?

0:09:31.700000 --> 0:09:35.140000
 And then I'll report that information
 up to the controller, then I'll

0:09:35.140000 --> 0:09:37.960000
 go back to the channel
 it's supposed to be on.

0:09:37.960000 --> 0:09:42.440000
 So this function is a part of what's
 called radio resource monitoring

0:09:42.440000 --> 0:09:44.720000
 or radio resource management.

0:09:44.720000 --> 0:09:50.760000
 Now, like it mentions, by default it
 spends only about 0.2% of its time

0:09:50.760000 --> 0:09:54.380000
 on there, so about, and once it leaves
 and it goes on to a different channel,

0:09:54.380000 --> 0:09:57.880000
 start scanning it, it's only scanning
 it for, like it says, 60 milliseconds

0:09:57.880000 --> 0:10:04.000000
 per scan. So if you're on the controller,
 yes, you're getting some data,

0:10:04.000000 --> 0:10:06.900000
 right? You're getting some data about
 this, these off-channel scans it's

0:10:06.900000 --> 0:10:10.320000
 doing, but the data is
 not very holistic.

0:10:10.320000 --> 0:10:13.340000
 It's not really giving you a very good
 picture because it was only on

0:10:13.340000 --> 0:10:16.820000
 those other channels for a very,
 very brief slice of time.

0:10:16.820000 --> 0:10:19.740000
 This is what monitor mode
 was designed to fix.

0:10:19.740000 --> 0:10:24.440000
 So with monitor mode you say, okay, I'm
 going to have my local mode access

0:10:24.440000 --> 0:10:27.740000
 points with my CAPWEP tunnels
 to the controller.

0:10:27.740000 --> 0:10:30.340000
 They've got clients associated to them,
 they can do what they want to

0:10:30.340000 --> 0:10:33.540000
 do, but I want to have a little bit more
 visibility into everything that's

0:10:33.540000 --> 0:10:39.740000
 going on. So the design idea is that
 for every five access points you

0:10:39.740000 --> 0:10:44.260000
 have, one of them should be placed in
 its own special mode called monitor

0:10:44.260000 --> 0:10:48.400000
 mode. And in monitor mode you can see
 here, the access point does not

0:10:48.400000 --> 0:10:50.040000
 accept any clients.

0:10:50.040000 --> 0:10:53.000000
 He's not there to service
 Wi-Fi clients.

0:10:53.000000 --> 0:10:57.400000
 What he's doing is he's scanning all
 the channels every 12 seconds and

0:10:57.400000 --> 0:11:01.640000
 he's spending a lot more time
 on all those channels.

0:11:01.640000 --> 0:11:05.420000
 So now because he's spending more time
 on them, he can import more accurate

0:11:05.420000 --> 0:11:10.140000
 statistics back to the controller.


0:11:10.140000 --> 0:11:14.320000
 So you can see here, here's a screenshot
 of what we might do on a controller

0:11:14.320000 --> 0:11:17.160000
 to set an access point
 to monitor mode.

0:11:17.160000 --> 0:11:21.940000
 And once it's set to monitor mode, it
 can detect a lot more things because

0:11:21.940000 --> 0:11:25.540000
 it's spending a lot more time on
 all these different channels.

0:11:25.540000 --> 0:11:28.480000
 I'm not going to go into the details
 of all those different attacks you

0:11:28.480000 --> 0:11:29.660000
 see there on the right.

0:11:29.660000 --> 0:11:32.040000
 Feel free to Google those
 or look those up.

0:11:32.040000 --> 0:11:37.360000
 But the point is we have an access
 point whose main primary job is to

0:11:37.360000 --> 0:11:41.780000
 monitor the surroundings, not for the
 clients, but just to see what's

0:11:41.780000 --> 0:11:45.880000
 going on there. So that
 is monitor mode.

0:11:45.880000 --> 0:11:50.260000
 And this particular case, you would
 go onto the controller to see your

0:11:50.260000 --> 0:11:54.520000
 graphs and charts and bars and everything
 about what data has been collected

0:11:54.520000 --> 0:11:59.160000
 by this access point and sent
 upstream to the controller.

0:11:59.160000 --> 0:12:00.560000
 Well, that's great.

0:12:00.560000 --> 0:12:04.680000
 But one thing this isn't necessarily
 going to show you is what if you

0:12:04.680000 --> 0:12:08.100000
 say to yourself, you know what, I would
 like to have an access point that

0:12:08.100000 --> 0:12:10.800000
 kind of does this right here.

0:12:10.800000 --> 0:12:14.120000
 I need an access point that's not really
 going to serve as clients, but

0:12:14.120000 --> 0:12:19.620000
 I want to see every single Wi-Fi
 data frame on any given channel.

0:12:19.620000 --> 0:12:21.840000
 As a matter of fact, I'd like
 to see that on my sniffer.

0:12:21.840000 --> 0:12:24.620000
 I'd like to, here's a really cool
 thing what I'd like to do.

0:12:24.620000 --> 0:12:28.280000
 I would like to have an access point
 that collects all this data on off

0:12:28.280000 --> 0:12:32.020000
-channel scanning, sends it up to the controller
 because after all, everything

0:12:32.020000 --> 0:12:32.820000
 goes to the controller.

0:12:32.820000 --> 0:12:37.220000
 But what if I could get that controller
 to then offload that data to another

0:12:37.220000 --> 0:12:41.960000
 device where I could open it up and like
 wire shark or arrow peak or something

0:12:41.960000 --> 0:12:45.060000
 like that. That brings
 us to our next mode.

0:12:45.060000 --> 0:12:48.620000
 We can put our access point into
 what's called sniffer mode.

0:12:48.620000 --> 0:12:53.140000
 Now this is very similar like it says
 here to monitor mode in that it's

0:12:53.140000 --> 0:12:56.220000
 not going to be accepting any
 clients, any Wi-Fi clients.

0:12:56.220000 --> 0:12:57.780000
 But here's the difference.

0:12:57.780000 --> 0:13:05.200000
 Look at this. When you were in monitor
 mode, it was spending a little

0:13:05.200000 --> 0:13:11.480000
 bit of time on every available 2.4
 gigahertz and 5 gigahertz channel.

0:13:11.480000 --> 0:13:14.840000
 And as reporting back to the controller,
 everything it heard across all

0:13:14.840000 --> 0:13:17.440000
 those channels. So we're talking about
 dozens of channels here between

0:13:17.440000 --> 0:13:20.900000
 2.4 gigahertz and 5 gigahertz.

0:13:20.900000 --> 0:13:24.600000
 In sniffer mode, number one, you put
 it in this mode so this is different

0:13:24.600000 --> 0:13:29.160000
 sniffer mode. And then part of this
 is you select an individual channel.

0:13:29.160000 --> 0:13:31.900000
 You tell the access point, hey, I want
 you to be in sniffer mode for channel

0:13:31.900000 --> 0:13:37.120000
 one or channel six or the 5 gigahertz
 spectrum for channel 48.

0:13:37.120000 --> 0:13:41.480000
 Now it's going to stay on there and
 it's going to capture all the Wi-Fi

0:13:41.480000 --> 0:13:44.520000
 traffic on that channel, send
 it to the controller.

0:13:44.520000 --> 0:13:46.720000
 Now here's the difference,
 a real big difference.

0:13:46.720000 --> 0:13:51.040000
 The controller now in turn is configured
 with the IP address of a host

0:13:51.040000 --> 0:13:56.220000
 like a server or even a laptop that's
 running, wire shark or omni-peak

0:13:56.220000 --> 0:13:59.000000
 or aeropique or air magnet.

0:13:59.000000 --> 0:14:02.300000
 And now all those captured packets
 that the controller is getting from

0:14:02.300000 --> 0:14:06.520000
 the AP are redirected
 to that host.

0:14:06.520000 --> 0:14:10.360000
 They're sent to the host encapsulated
 in UDP with a sourced UDP port of

0:14:10.360000 --> 0:14:15.060000
 55.55 and a destination
 port of 5,000.

0:14:15.060000 --> 0:14:20.680000
 And now you can display all of them in
 wire shark or omni-peak or aeropique

0:14:20.680000 --> 0:14:26.160000
 or air magnet. Now there's another
 mode that's sort of similar to all

0:14:26.160000 --> 0:14:30.840000
 of these things here,
 which is sensor mode.

0:14:30.840000 --> 0:14:33.740000
 Now let's say here's
 your situation.

0:14:33.740000 --> 0:14:38.360000
 Let's say you know what, I've got thousands
 of Wi-Fi clients connected

0:14:38.360000 --> 0:14:44.340000
 to my access points, but I'm really only
 alert to problems after the fact.

0:14:44.340000 --> 0:14:49.140000
 I'm tired of getting phone calls saying,
 hey, the network is really slow.

0:14:49.140000 --> 0:14:53.560000
 I'm getting a lot of latency to my email
 server or to my web browser or,

0:14:53.560000 --> 0:14:57.580000
 hey, the time it's taking me to authenticate
 and connect to the wireless

0:14:57.580000 --> 0:15:00.240000
 LAN in the first place
 is taking forever.

0:15:00.240000 --> 0:15:05.220000
 I'd like to sort of detect that in advance
 before my employees start calling

0:15:05.220000 --> 0:15:06.460000
 me up with these problems.

0:15:06.460000 --> 0:15:11.460000
 It would be really cool if I could have
 an access point that sort of acted

0:15:11.460000 --> 0:15:15.860000
 like a Wi-Fi client, an access point
 that actually started associating

0:15:15.860000 --> 0:15:20.340000
 to other access points that were around
 it like laptops do like tablets

0:15:20.340000 --> 0:15:25.160000
 do. And then once it was associated, it
 could report back to the controller,

0:15:25.160000 --> 0:15:28.500000
 hey, how long did it take me to associate
 to each of the access points

0:15:28.500000 --> 0:15:32.420000
 around me? Even more than that, what
 if that access point, once it was

0:15:32.420000 --> 0:15:36.500000
 associated, could run some network
 tests like it could try to contact

0:15:36.500000 --> 0:15:40.440000
 an email server, try to contact a web server
 and report back to the controller

0:15:40.440000 --> 0:15:42.400000
 how long that took.

0:15:42.400000 --> 0:15:46.360000
 Or maybe it wasn't successful at
 all with those network tests.

0:15:46.360000 --> 0:15:48.100000
 Wouldn't that be nice?

0:15:48.100000 --> 0:15:51.220000
 That's what sensor
 mode is all about.

0:15:51.220000 --> 0:15:57.160000
 So in sensor mode, this is a solution
 involving three components, a wireless

0:15:57.160000 --> 0:16:03.340000
 LAN controller, an access point,
 and Cisco DNA center.

0:16:03.340000 --> 0:16:07.120000
 So you have to have all three of these
 components to get the most effect

0:16:07.120000 --> 0:16:08.760000
 out of sensor mode.

0:16:08.760000 --> 0:16:10.700000
 So here's how this works.

0:16:10.700000 --> 0:16:13.620000
 You start by going into
 Cisco DNA center.

0:16:13.620000 --> 0:16:16.780000
 Now in case you're not familiar with
 the Cisco DNA center, I'd recommend

0:16:16.780000 --> 0:16:19.800000
 you watch some of our other videos
 in which we give an introduction to

0:16:19.800000 --> 0:16:24.640000
 that. But just in a very high level
 nutshell here, Cisco DNA center is

0:16:24.640000 --> 0:16:26.040000
 sold as an appliance.

0:16:26.040000 --> 0:16:30.740000
 So it's a physical box that you rack
 and stack into a rack somewhere.

0:16:30.740000 --> 0:16:34.940000
 But it has special software inside
 of it that can program and control

0:16:34.940000 --> 0:16:37.480000
 pretty much all the elements
 of your network.

0:16:37.480000 --> 0:16:41.360000
 It can program and automate your routers,
 your switches, and your access

0:16:41.360000 --> 0:16:45.640000
 points. It can reach out to a controller
 and send down templates to the

0:16:45.640000 --> 0:16:47.120000
 controller and all
 sorts of things.

0:16:47.120000 --> 0:16:51.420000
 So it's sort of like a high level automation
 and programming tool that

0:16:51.420000 --> 0:16:54.080000
 you can implement
 into your network.

0:16:54.080000 --> 0:16:56.240000
 So here's how this works.

0:16:56.240000 --> 0:17:00.620000
 You start, first of all, by getting DNA
 center and the controller to talk

0:17:00.620000 --> 0:17:04.200000
 to each other, so they have to associate
 to each other and know each other.

0:17:04.200000 --> 0:17:07.680000
 Then on Cisco DNA center, within like
 wireless profiles, you configure

0:17:07.680000 --> 0:17:10.980000
 these various wireless tests.

0:17:10.980000 --> 0:17:16.700000
 And then the controller will receive
 those pre-configured tests from DNA

0:17:16.700000 --> 0:17:22.040000
 center. The controller in turn will
 push those tests down to your access

0:17:22.040000 --> 0:17:25.820000
 points that are operating
 in sensor mode.

0:17:25.820000 --> 0:17:32.600000
 Now also the controller will tell the
 various access points, hey, here

0:17:32.600000 --> 0:17:35.280000
 are the SSID's I want you to test.


0:17:35.280000 --> 0:17:40.120000
 So while you're in sensor mode, test
 the SSID of corporate of guests,

0:17:40.120000 --> 0:17:43.440000
 you know, of all the access points
 you can hear from, so you tell the

0:17:43.440000 --> 0:17:47.800000
 sensor mode AP, hey, sensor mode AP,
 you're going to hear a bunch of other

0:17:47.800000 --> 0:17:51.320000
 access points around you, broadcasting
 their beacons.

0:17:51.320000 --> 0:17:55.300000
 When you hear five or ten or fifteen other
 access points around you, they're

0:17:55.300000 --> 0:17:59.360000
 all broadcasting the beacon
 of corporate or guest.

0:17:59.360000 --> 0:18:03.020000
 What I want you to do is I want you
 to connect to each one of them in

0:18:03.020000 --> 0:18:05.100000
 turn as a client.

0:18:05.100000 --> 0:18:08.180000
 I want you to associate
 to those access points.

0:18:08.180000 --> 0:18:09.880000
 And then I want you to start
 running these tests.

0:18:09.880000 --> 0:18:12.880000
 I want you to start running some onboarding
 tests and report back to me.

0:18:12.880000 --> 0:18:14.820000
 How long did it take
 you to associate?

0:18:14.820000 --> 0:18:18.260000
 How long did it take you to
 authenticate, like a client?

0:18:18.260000 --> 0:18:20.660000
 I want you to do a network test.

0:18:20.660000 --> 0:18:24.040000
 How long did it take you to
 actually get an IP address?

0:18:24.040000 --> 0:18:26.980000
 I want you to do some
 application tests.

0:18:26.980000 --> 0:18:31.080000
 How long did it take you to reach my
 email server or to reach my TFTP

0:18:31.080000 --> 0:18:36.340000
 or FTP server? And then all those results,
 those test results will be

0:18:36.340000 --> 0:18:41.360000
 sent directly from the
 AP back to DNA center.

0:18:41.360000 --> 0:18:45.940000
 So in this particular environment here,
 the main job of the controller

0:18:45.940000 --> 0:18:49.980000
 is to speak to the lightweight access
 points, say, here's the mode you're

0:18:49.980000 --> 0:18:52.560000
 in. You need to be in sensor mode.


0:18:52.560000 --> 0:18:54.780000
 Here's the tests I
 want you to run.

0:18:54.780000 --> 0:18:58.140000
 And I want you to run these tests
 against these various SSIDs.

0:18:58.140000 --> 0:19:03.000000
 At that point, the controller sits back,
 the access point goes into the

0:19:03.000000 --> 0:19:07.000000
 sensor mode and does all this stuff
 and communicates directly with DNA

0:19:07.000000 --> 0:19:10.600000
 center, with the server running DNA
 center and says, hey, DNA center,

0:19:10.600000 --> 0:19:12.620000
 here's all the stuff I found.

0:19:12.620000 --> 0:19:14.740000
 So here's an example screenshot.

0:19:14.740000 --> 0:19:19.480000
 This is taken from Cisco.com's website
 of all the various different tests

0:19:19.480000 --> 0:19:23.440000
 you could put your sensor AP into.


0:19:23.440000 --> 0:19:30.540000
 The last mode I want to talk about
 in this video is mesh mode.

0:19:30.540000 --> 0:19:34.440000
 Like the first bullet says, you're going
 to have some environments where

0:19:34.440000 --> 0:19:38.120000
 you want to provide Wi-Fi access to
 clients, so they're going to need

0:19:38.120000 --> 0:19:40.680000
 an access point to associate,
 but here's the problem.

0:19:40.680000 --> 0:19:45.160000
 Where that access point is physically
 located, there might not be any

0:19:45.160000 --> 0:19:47.360000
 physical connection for Ethernet.

0:19:47.360000 --> 0:19:51.140000
 You might not be able to string an Ethernet
 cable out to that access point.

0:19:51.140000 --> 0:19:52.780000
 Think of it being in a park.

0:19:52.780000 --> 0:19:57.200000
 Maybe it's on top of a telephone pole
 or a light pole, a city street,

0:19:57.200000 --> 0:20:00.840000
 or maybe an amphitheater,
 or even a warehouse.

0:20:00.840000 --> 0:20:04.420000
 These are situations where we need to
 have an access point out there to

0:20:04.420000 --> 0:20:08.360000
 give people Wi-Fi connectivity, but once
 they're associated to that access

0:20:08.360000 --> 0:20:10.100000
 point, and they send their Wi-Fi connection
 to the network, they send

0:20:10.100000 --> 0:20:10.100000
 their Wi-Fi connection
 to the network.

0:20:10.100000 --> 0:20:14.600000
 If you send Wi-Fi frames to that access
 point, there's no wired connection.

0:20:14.600000 --> 0:20:16.680000
 So where do we go from there?

0:20:16.680000 --> 0:20:18.260000
 What if we had this?

0:20:18.260000 --> 0:20:21.220000
 What if we had a series of
 access points like that?

0:20:21.220000 --> 0:20:25.000000
 One access point connects to the clients,
 receives the data, now it sends

0:20:25.000000 --> 0:20:28.540000
 that data to access point
 number two, wirelessly.

0:20:28.540000 --> 0:20:32.640000
 It sends that data to access point number
 three wirelessly, and we keep

0:20:32.640000 --> 0:20:38.260000
 going hop by hop by hop until we reach
 an access point that actually does

0:20:38.260000 --> 0:20:39.360000
 have wired Ethernet.

0:20:39.360000 --> 0:20:43.120000
 That does have a connection to
 the wired distribution system.

0:20:43.120000 --> 0:20:47.100000
 That is the whole concept
 behind mesh.

0:20:47.100000 --> 0:20:52.360000
 So this is a mode of access points in
 which they will associate with each

0:20:52.360000 --> 0:20:58.760000
 other to carry data from a Wi-Fi client
 through multiple mesh nodes and

0:20:58.760000 --> 0:21:03.880000
 ultimately be able to place that data
 onto the wired distribution system.

0:21:03.880000 --> 0:21:08.160000
 So this is what it looks
 like right here.

0:21:08.160000 --> 0:21:10.720000
 So let's talk about mesh
 mode a little bit more.

0:21:10.720000 --> 0:21:16.680000
 So when an access point is placed into
 mesh mode, it can operate in one

0:21:16.680000 --> 0:21:22.100000
 of two ways. As what's called a root
 access point, which means that mesh

0:21:22.100000 --> 0:21:27.080000
 access point can associate with other
 access points, and in addition to

0:21:27.080000 --> 0:21:30.740000
 that, it has wired access
 to a controller.

0:21:30.740000 --> 0:21:33.580000
 So once a root access point, that means
 we've got an access point that

0:21:33.580000 --> 0:21:37.740000
 physically has at least one Ethernet
 cable plugged into the back of it.

0:21:37.740000 --> 0:21:41.700000
 And when it forms a capwap tunnel to
 the controller, that capwap tunnel

0:21:41.700000 --> 0:21:45.560000
 is going to be going across the
 wired distribution system.

0:21:45.560000 --> 0:21:49.640000
 Or for the access points that we have
 stuck out on light poles or electrical

0:21:49.640000 --> 0:21:53.980000
 poles or something like that that have
 no physical Ethernet cable plugged

0:21:53.980000 --> 0:21:58.940000
 into them, those will be called
 maps, mesh access points.

0:21:58.940000 --> 0:22:03.400000
 They will also connect to the controller
 because after all, these are

0:22:03.400000 --> 0:22:05.440000
 still lightweight access points.

0:22:05.440000 --> 0:22:09.460000
 So they will still have to form capwap
 control and data tunnels to the

0:22:09.460000 --> 0:22:15.800000
 controller, but their tunnels will be
 running through other access points.

0:22:15.800000 --> 0:22:22.600000
 So what a mesh Wi-Fi network requires
 at least one root access point and

0:22:22.600000 --> 0:22:26.840000
 then one or more mesh
 access points.

0:22:26.840000 --> 0:22:32.340000
 So the idea is once a mesh access point
 receives data, either from a directly

0:22:32.340000 --> 0:22:39.300000
 associated Wi-Fi client, like a laptop
 or a tablet or a smartphone, it

0:22:39.300000 --> 0:22:44.960000
 needs to get that data to the root access
 point, the quickest path possible.

0:22:44.960000 --> 0:22:49.900000
 Now that data might have to jump across
 several other mesh access points

0:22:49.900000 --> 0:22:52.020000
 before it gets to the
 root access point.

0:22:52.020000 --> 0:22:54.000000
 How is it going to determine
 the best path?

0:22:54.000000 --> 0:22:56.020000
 Well that's what this bullet
 point is talking about.

0:22:56.020000 --> 0:23:00.600000
 It's going to use the Cisco adaptive
 wireless path protocol to determine

0:23:00.600000 --> 0:23:05.040000
 the best path through the other mesh access
 points to get to the controller.

0:23:05.040000 --> 0:23:10.840000
 Now each of those mesh access points
 can also simultaneously operate in

0:23:10.840000 --> 0:23:12.580000
 any one of the previously
 mentioned modes.

0:23:12.580000 --> 0:23:16.200000
 We've talked about sniffer mode, monitor
 mode, sensor mode, so mesh access

0:23:16.200000 --> 0:23:19.620000
 point could also be
 doing that as well.

0:23:19.620000 --> 0:23:23.600000
 And lastly, in this video I just want
 to briefly talk about what the traffic

0:23:23.600000 --> 0:23:27.400000
 flow looks like from the
 client's perspective.

0:23:27.400000 --> 0:23:31.640000
 So each of these mesh access points is
 presumably going to have two radios

0:23:31.640000 --> 0:23:36.880000
 on it, a 2.4GHz radio
 and a 5GHz radio.

0:23:36.880000 --> 0:23:41.860000
 So your clients, your tablets, your smartphones,
 they're going to associate

0:23:41.860000 --> 0:23:46.640000
 on an SSID that's advertised
 on the 2.4GHz radio.

0:23:46.640000 --> 0:23:48.560000
 That's where they're going
 to send their data.

0:23:48.560000 --> 0:23:49.860000
 Now here's the interesting thing.

0:23:49.860000 --> 0:23:54.120000
 At that point, the mesh access point
 is going to transfer that data to

0:23:54.120000 --> 0:24:00.080000
 its 5GHz radio and transfer it across
 a special SSID that's used as a

0:24:00.080000 --> 0:24:05.440000
 backhaul network that's only used for
 one mesh access point to talk to

0:24:05.440000 --> 0:24:07.080000
 another mesh access point.

0:24:07.080000 --> 0:24:11.100000
 So for example, we've seen an example
 animation of that right here, is

0:24:11.100000 --> 0:24:13.740000
 that data is going from
 one map to another.

0:24:13.740000 --> 0:24:17.720000
 This is happening across the
 5GHz backhaul network.

0:24:17.720000 --> 0:24:21.620000
 Finally, the data gets to
 the root access point.

0:24:21.620000 --> 0:24:26.460000
 He's got a physical wired ethernet connection,
 so now he can dump it onto

0:24:26.460000 --> 0:24:28.120000
 the wired network.

0:24:28.120000 --> 0:24:32.960000
 This whole time that data has been
 going into a CAPWAP tunnel or being

0:24:32.960000 --> 0:24:35.840000
 transferred across
 a CAPWAP tunnel.

0:24:35.840000 --> 0:24:39.880000
 So that concludes this video.

0:24:39.880000 --> 0:24:40.780000
 Thank you for watching.

