1
00:00:02,339 --> 00:00:05,589
(modern digital music)

2
00:00:09,079 --> 00:00:10,953
- [Instructor] In the last
video, when I introduced you

3
00:00:10,953 --> 00:00:12,946
to the concept of configuring OSPF

4
00:00:12,946 --> 00:00:15,178
and showed you most of the
commands you would need,

5
00:00:15,178 --> 00:00:18,712
I verbally introduced
the concept of OSPF Cost.

6
00:00:18,712 --> 00:00:21,192
I want to have a special
video just dedicated to that

7
00:00:21,192 --> 00:00:23,094
because I think it's very important that

8
00:00:23,094 --> 00:00:24,968
for each routing protocol you learn about,

9
00:00:24,968 --> 00:00:28,457
that you're able to understand
the metric type that's used

10
00:00:28,457 --> 00:00:30,529
by that protocol so you can compare

11
00:00:30,529 --> 00:00:32,601
and contrast them along the way.

12
00:00:32,601 --> 00:00:35,038
So hopefully by this point,
you've learned about RIP

13
00:00:35,038 --> 00:00:39,205
and the routing metric
for RIP is hop count.

14
00:00:40,198 --> 00:00:43,544
And you've learned about
EIRGP and the routing metric

15
00:00:43,544 --> 00:00:47,990
for EIRGP is called distance.

16
00:00:47,990 --> 00:00:50,587
Now the routing metric that
we're gonna deal with, OSPF,

17
00:00:50,587 --> 00:00:54,746
is called OSPF Cost.

18
00:00:54,746 --> 00:00:56,062
So like Spanning-Tree,

19
00:00:56,062 --> 00:00:57,778
if you've learned about Spanning-Tree,

20
00:00:57,778 --> 00:00:58,703
this should be easy.

21
00:00:58,703 --> 00:01:01,343
Because just like
Spanning-Tree, cost is a value

22
00:01:01,343 --> 00:01:04,303
that's derived from the
interface bandwidth.

23
00:01:04,303 --> 00:01:07,349
And just like Spanning-Tree,
the greater the bandwidth,

24
00:01:07,349 --> 00:01:10,387
the faster the interface,
the lower the cost.

25
00:01:10,387 --> 00:01:12,743
And just like in Spanning-Tree,
if I have two paths

26
00:01:12,743 --> 00:01:16,910
to a particular place, the
lower cost is the better path.

27
00:01:18,174 --> 00:01:22,614
Now, OSPF does not use the
same formula as Spanning-Tree.

28
00:01:22,614 --> 00:01:24,732
So, you don't have to worry about that

29
00:01:24,732 --> 00:01:26,519
so that the numbers are
not going to be the same.

30
00:01:26,519 --> 00:01:28,510
As an example, review question.

31
00:01:28,510 --> 00:01:30,969
In LAN switching with Spanning-Tree,

32
00:01:30,969 --> 00:01:33,086
what was the Spanning-Tree Cost

33
00:01:33,086 --> 00:01:35,687
of a fast ethernet interface,

34
00:01:35,687 --> 00:01:40,567
so a 100 megabit per second
fast ethernet interface.

35
00:01:40,567 --> 00:01:43,166
Hopefully you answered the number 19.

36
00:01:43,166 --> 00:01:46,374
Fast ethernet is 19th in
the world of Spanning-Tree.

37
00:01:46,374 --> 00:01:50,541
Well, in OSPF, the cost of a
fast ethernet interface is one.

38
00:01:51,654 --> 00:01:53,487
So, different formula.

39
00:01:55,876 --> 00:01:59,815
And the cost of an OSPF
interface will default

40
00:01:59,815 --> 00:02:02,290
to be whatever you know,
derived from the bandwidth,

41
00:02:02,290 --> 00:02:04,323
but you can change that,
you can explicitly configure

42
00:02:04,323 --> 00:02:08,101
the cost of an interface or if you modify

43
00:02:08,101 --> 00:02:10,660
the bandwidth of an
interface, that implicitly

44
00:02:10,660 --> 00:02:12,531
changes the cost as well.

45
00:02:12,531 --> 00:02:14,397
So there are two ways
that you can change it.

46
00:02:14,397 --> 00:02:15,819
You can go on to an interface and use

47
00:02:15,819 --> 00:02:19,799
the ip ospf cost command
and then explicitly

48
00:02:19,799 --> 00:02:22,770
set the value to whatever
you want, or like I said,

49
00:02:22,770 --> 00:02:26,937
by changing the bandwidth,
that will also affect it.

50
00:02:28,049 --> 00:02:31,389
And you can use the command
show ip ospf interface

51
00:02:32,433 --> 00:02:34,753
to actually see what the cost
is of any given interface

52
00:02:34,753 --> 00:02:37,349
and certainly when you
look at an ospf route

53
00:02:37,349 --> 00:02:39,870
in the routing table with
the command show ip route,

54
00:02:39,870 --> 00:02:41,860
or show ip route ospf.

55
00:02:41,860 --> 00:02:44,621
You'll see what the
total cumulative cost is

56
00:02:44,621 --> 00:02:46,977
to reach any given destination.

57
00:02:46,977 --> 00:02:49,572
So let's see an example of this.

58
00:02:49,572 --> 00:02:51,887
So on our whiteboard here, we can see that

59
00:02:51,887 --> 00:02:55,586
if we look from Switch-3's perspective,

60
00:02:55,586 --> 00:02:59,077
and we look at his way of
getting to the 3.2.3 network,

61
00:02:59,077 --> 00:03:02,657
he actually has two equal cost paths.

62
00:03:02,657 --> 00:03:05,214
He can get to there via Switch-2,

63
00:03:05,214 --> 00:03:07,854
or you can get there via Router-3.

64
00:03:07,854 --> 00:03:09,559
So if we actually go into Switch-3,

65
00:03:09,559 --> 00:03:13,717
we take a look as routing
table, that confirms that.

66
00:03:13,717 --> 00:03:15,380
We can see right here, 3.2.3.0

67
00:03:15,380 --> 00:03:17,871
and he's got two equal cost paths.

68
00:03:17,871 --> 00:03:20,188
They both have a cost of two.

69
00:03:20,188 --> 00:03:23,323
And that makes sense, because
this is a fast ethernet link

70
00:03:23,323 --> 00:03:26,449
so that's a cost of one, and
this is a fast ethernet link,

71
00:03:26,449 --> 00:03:28,437
so that gives us another cost of one.

72
00:03:28,437 --> 00:03:30,467
So one plus one is two going this way.

73
00:03:30,467 --> 00:03:33,272
One plus one is two going this way.

74
00:03:33,272 --> 00:03:38,070
So let me start by saying,
okay, maybe I want Switch-3

75
00:03:38,070 --> 00:03:39,903
only to use this path.

76
00:03:41,834 --> 00:03:46,001
So what I'm gonna do, I'm
gonna go on to Switch-2.

77
00:03:47,963 --> 00:03:50,322
I'm gonna go on to as fast
ethernet, 0/3 interface

78
00:03:50,322 --> 00:03:52,739
and I'm gonna raise the cost.

79
00:03:54,090 --> 00:03:58,173
I'm gonna set the cost to
five on that interface.

80
00:03:59,251 --> 00:04:01,891
So then, this path will
not be as preferable.

81
00:04:01,891 --> 00:04:04,159
That will be a total cost of six.

82
00:04:04,159 --> 00:04:06,825
This will be a cost of two.

83
00:04:06,825 --> 00:04:09,060
And so Switch-3 will
now only have one route

84
00:04:09,060 --> 00:04:10,607
in his routing table.

85
00:04:10,607 --> 00:04:14,061
So I'm gonna go to
Switch-2, sorry, Switch-3

86
00:04:14,061 --> 00:04:15,987
will have a single route
in his writing table

87
00:04:15,987 --> 00:04:17,470
going this way.

88
00:04:17,470 --> 00:04:18,649
So now I'm gonna go to Switch-2.

89
00:04:18,649 --> 00:04:20,849
I'm gonna go on a fast ethernet 0/3,

90
00:04:20,849 --> 00:04:24,766
I'm gonna officially
increase the cost to five.

91
00:04:28,278 --> 00:04:32,252
Okay, so, #int fast 0/3,

92
00:04:32,252 --> 00:04:33,747
#ip ospf cost,

93
00:04:33,747 --> 00:04:35,192
actually, before I do it,

94
00:04:35,192 --> 00:04:39,109
#do show ip ospf interface fast 0/3.

95
00:04:41,889 --> 00:04:45,015
And you can see, by default, it's Cost: 1,

96
00:04:45,015 --> 00:04:46,727
'cause fast ethernet.

97
00:04:46,727 --> 00:04:49,644
Now I'm gonna type #ip ospf cost 5.

98
00:04:51,113 --> 00:04:55,280
And now when I take a look at
the output of that command,

99
00:04:56,385 --> 00:04:59,517
now we can verify that the cost is five.

100
00:04:59,517 --> 00:05:01,996
So, at this point if
I go back to Switch-3,

101
00:05:01,996 --> 00:05:05,650
he should now see a total
cost of six going this way

102
00:05:05,650 --> 00:05:08,130
and a cost of two going this way.

103
00:05:08,130 --> 00:05:11,422
So only this path, the path via Router-3

104
00:05:11,422 --> 00:05:15,587
should now be the only path
to get to the 3.2.3 network.

105
00:05:15,587 --> 00:05:18,420
(keyboard clicks)

106
00:05:22,705 --> 00:05:23,885
And that's what we see.

107
00:05:23,885 --> 00:05:27,885
Now there's only one path
and it's via Router-3.

108
00:05:29,248 --> 00:05:30,915
Now, let's just change it one more time.

109
00:05:30,915 --> 00:05:33,349
So now what I want to do is I want to have

110
00:05:33,349 --> 00:05:36,720
Switch-3 prefer this path.

111
00:05:36,720 --> 00:05:38,831
I want this to be the better path.

112
00:05:38,831 --> 00:05:41,512
So what I'm gonna do, is I'm
gonna go under Router-3's

113
00:05:41,512 --> 00:05:42,856
fast ethernet interface.

114
00:05:42,856 --> 00:05:46,834
I'm gonna take the bandwidth
and I'm gonna lower it

115
00:05:46,834 --> 00:05:48,990
to some really small number.

116
00:05:48,990 --> 00:05:51,177
Make this interface look
like it's incredibly slow

117
00:05:51,177 --> 00:05:53,574
by giving it a really low bandwidth.

118
00:05:53,574 --> 00:05:56,257
And by making the bandwidth
number really small,

119
00:05:56,257 --> 00:05:59,665
that will make the cost really big.

120
00:05:59,665 --> 00:06:01,420
Because remember, the larger the cost,

121
00:06:01,420 --> 00:06:03,977
the less preferable it its.

122
00:06:03,977 --> 00:06:05,519
So let's go on the Router-3 now

123
00:06:05,519 --> 00:06:08,510
and change it's interface bandwidth.

124
00:06:08,510 --> 00:06:11,343
(keyboard clicks)

125
00:06:13,447 --> 00:06:15,674
Your fast paced ethernet 0/0,

126
00:06:15,674 --> 00:06:19,453
#do sho int fast 0/0 so
we can see right now,

127
00:06:19,453 --> 00:06:23,620
it's current bandwidth is 100000 kbit/sec.

128
00:06:25,545 --> 00:06:27,859
So if you actually do the math,
that's one hundred million

129
00:06:27,859 --> 00:06:29,000
bits per second.

130
00:06:29,000 --> 00:06:31,641
So now I'm gonna say, #bandwidth.

131
00:06:31,641 --> 00:06:35,808
How about we say, 2000 kilo
bits per second, really slow.

132
00:06:37,737 --> 00:06:39,904
Only 2000 bits per second.

133
00:06:42,532 --> 00:06:46,699
So now if I type sho ip ospf int fast 0/0,

134
00:06:48,736 --> 00:06:51,069
look at his cost now, 50000.

135
00:06:52,324 --> 00:06:55,540
It was one before, and now it's 50000.

136
00:06:55,540 --> 00:06:57,449
So we can see how modifying the bandwidth

137
00:06:57,449 --> 00:07:00,005
clearly affects the OSPF Cost.

138
00:07:00,005 --> 00:07:03,088
And lastly, if I go over to Switch-3,

139
00:07:06,306 --> 00:07:09,960
now we can see that the 3.2.3
route has switched over.

140
00:07:09,960 --> 00:07:13,210
It's now pointing at Switch-2, 2.3.2.22

141
00:07:14,425 --> 00:07:16,941
as the next hop, because the cost of six

142
00:07:16,941 --> 00:07:20,695
is certainly better than
the cost of 50000 and one.

143
00:07:20,695 --> 00:07:23,945
(modern digital music)

