1
00:00:09,032 --> 00:00:11,016
- We're gonna start
adding some configuration

2
00:00:11,016 --> 00:00:12,049
to these devices.

3
00:00:12,049 --> 00:00:15,614
So we're gonna add IP
addresses and static routes.

4
00:00:15,614 --> 00:00:17,859
By the time we're done with
this particular section

5
00:00:17,859 --> 00:00:21,491
we still will not have
end-to-end connectivity,

6
00:00:21,491 --> 00:00:24,275
because we haven't completed
our VLAN configuration

7
00:00:24,275 --> 00:00:25,347
and spanning tree yet,

8
00:00:25,347 --> 00:00:28,162
so we will not have
end-to-end connectivity

9
00:00:28,162 --> 00:00:30,066
at the end of this section yet.

10
00:00:30,066 --> 00:00:32,246
So let's go ahead and
add our IP addresses,

11
00:00:32,246 --> 00:00:35,712
and static routes where they need to be.

12
00:00:35,712 --> 00:00:39,879
So, let's bring our topology
diagram back in to play.

13
00:00:41,738 --> 00:00:44,270
And in case you had not already
taken a screen shot of this,

14
00:00:44,270 --> 00:00:45,856
you will want to,

15
00:00:45,856 --> 00:00:47,125
because these are the IP addresses

16
00:00:47,125 --> 00:00:48,218
we're gonna want to implement.

17
00:00:48,218 --> 00:00:49,669
Now once again, when you're building this,

18
00:00:49,669 --> 00:00:52,869
you can use whatever
IP addressing you want,

19
00:00:52,869 --> 00:00:55,869
I just chose this to make it simple.

20
00:00:58,412 --> 00:01:00,749
Okay, so I'm going to start with,

21
00:01:00,749 --> 00:01:02,927
let's start just working
from left to right.

22
00:01:02,927 --> 00:01:05,557
I'll start with router-1,

23
00:01:05,557 --> 00:01:07,079
and I will turn him on.

24
00:01:07,079 --> 00:01:08,844
I've got quite a few
devices in this topology

25
00:01:08,844 --> 00:01:11,028
so I may not want to turn them on.

26
00:01:11,028 --> 00:01:14,064
Let's see here actually I've
only got one, two, three, four,

27
00:01:14,064 --> 00:01:16,376
I've got five IOS
devices, so it's probably

28
00:01:16,376 --> 00:01:19,709
pretty safe to turn them all on at once.

29
00:01:20,948 --> 00:01:25,031
Okay, so let's go ahead
and go into router-1 now.

30
00:01:30,726 --> 00:01:35,007
As that's coming up, it's
gonna be fast ethernet 0/0

31
00:01:35,007 --> 00:01:37,117
on this particular router that
we're gonna want to configure

32
00:01:37,117 --> 00:01:39,495
as an 802.1q trunk.

33
00:01:39,495 --> 00:01:41,261
So we're basically configuring
what's called a router

34
00:01:41,261 --> 00:01:43,344
on a stick as this point.

35
00:01:44,884 --> 00:01:47,365
The interface fast ethernet 0/0.

36
00:01:47,365 --> 00:01:49,920
All we have to do here is no shut.

37
00:01:49,920 --> 00:01:51,338
But before I do that,

38
00:01:51,338 --> 00:01:54,973
I'm gonna wanna create my sub-interfaces.

39
00:01:54,973 --> 00:01:58,168
And I'm supporting VLAN's
four and five, so I'll do

40
00:01:58,168 --> 00:01:59,793
subinterface four to begin with.

41
00:01:59,793 --> 00:02:03,032
It could be any number I
want, I'm just choosing that.

42
00:02:03,032 --> 00:02:04,865
Encapsulation dot1q 4,

43
00:02:05,998 --> 00:02:10,351
That makes sure that he
understands that 802.1q tags,

44
00:02:10,351 --> 00:02:12,170
and that anything that arrives with a tag

45
00:02:12,170 --> 00:02:15,654
value of four, or needs to
leave with a tag value of four,

46
00:02:15,654 --> 00:02:19,737
the VLAN of four, will use
this particular sub-interface.

47
00:02:19,737 --> 00:02:22,987
And then select the correct IP address.

48
00:02:27,590 --> 00:02:29,863
Alright, and then rinse and repeat.

49
00:02:29,863 --> 00:02:32,817
Do the same thing for
our next sub-interface.

50
00:02:32,817 --> 00:02:34,372
I'm just using the up arrow here

51
00:02:34,372 --> 00:02:37,122
to go through my command history.

52
00:02:38,082 --> 00:02:41,582
Just making slight changes as we go along.

53
00:02:45,000 --> 00:02:46,833
Okay, now before I leave this,

54
00:02:46,833 --> 00:02:48,625
I also need to put in a static route,

55
00:02:48,625 --> 00:02:49,766
and then the last thing I'll do

56
00:02:49,766 --> 00:02:52,436
is bring up that physical interface.

57
00:02:52,436 --> 00:02:54,404
Alright so static route.

58
00:02:54,404 --> 00:02:58,370
Why don't we just create a
single default route in this guy?

59
00:02:58,370 --> 00:03:00,902
Because really there's
only one way out on him,

60
00:03:00,902 --> 00:03:03,024
he doesn't have multiple egress points.

61
00:03:03,024 --> 00:03:05,357
So IP route 0.0.0.0 0.0.0.0,

62
00:03:06,837 --> 00:03:09,442
that says anything you don't know about,

63
00:03:09,442 --> 00:03:11,359
let's have him go to...

64
00:03:13,236 --> 00:03:15,777
Well he's got two possible
people he could go to,

65
00:03:15,777 --> 00:03:18,099
VLAN-4, or VLAN-5 on his

66
00:03:18,099 --> 00:03:20,599
counterpart which is router-2.

67
00:03:21,856 --> 00:03:26,026
So doesn't really matter,
we'll just select one of them.

68
00:03:26,026 --> 00:03:29,276
Let's select in this particular case...

69
00:03:31,511 --> 00:03:33,729
Let's do it this way.

70
00:03:33,729 --> 00:03:36,371
Let's bring in this drawing here.

71
00:03:36,371 --> 00:03:38,907
Let's configure Router-1 so
that if he's trying to get

72
00:03:38,907 --> 00:03:40,657
to the 2.3.2 network,

73
00:03:42,252 --> 00:03:44,169
he'll go across VLAN-4,

74
00:03:45,216 --> 00:03:49,549
and if he's trying to
get the 3.2.3 network,

75
00:03:49,549 --> 00:03:51,618
he'll go across VLAN-5.

76
00:03:51,618 --> 00:03:53,955
So that will necessitate two different

77
00:03:53,955 --> 00:03:56,122
static routes in router-1.

78
00:03:57,775 --> 00:04:01,108
Alright so, to get to the 2.3.2 network,

79
00:04:04,114 --> 00:04:06,864
your next hop is gonna be 1.2.4.2

80
00:04:09,779 --> 00:04:12,446
and to get to the 3.2.3 network,

81
00:04:16,762 --> 00:04:19,262
your next hop will be 1.2.5.2,

82
00:04:22,094 --> 00:04:23,883
and now the last thing is
we need to go back into his

83
00:04:23,883 --> 00:04:26,800
physical interface and bring it up.

84
00:04:28,582 --> 00:04:30,499
Save our configuration.

85
00:04:33,752 --> 00:04:36,386
Okay so we are done with that router.

86
00:04:36,386 --> 00:04:38,136
I can get rid of him.

87
00:04:40,316 --> 00:04:42,102
Now as far as IP addressing is concerned,

88
00:04:42,102 --> 00:04:43,782
let's go over to the far right,

89
00:04:43,782 --> 00:04:45,874
and go to router-3.

90
00:04:45,874 --> 00:04:48,130
Configure router-3.

91
00:04:48,130 --> 00:04:49,490
It's gonna be pretty much the same

92
00:04:49,490 --> 00:04:52,490
kind of thing as we did in router-1.

93
00:04:54,215 --> 00:04:57,061
So I'll just start by
configuring my static routes,

94
00:04:57,061 --> 00:05:00,832
IP route 1.2.4.0

95
00:05:00,832 --> 00:05:05,063
255 255 255 0

96
00:05:05,063 --> 00:05:09,230
and we want that to go to
the next hop of 2.3.2.2,

97
00:05:11,009 --> 00:05:15,176
an IP route of 1.2.5.0,

98
00:05:20,077 --> 00:05:24,244
we want that to go to 3.2.3.2.

99
00:05:27,793 --> 00:05:31,567
Okay that'll accomplish
load balancing on that side,

100
00:05:31,567 --> 00:05:34,972
and then go to interface
fast ethernet 0/0,

101
00:05:34,972 --> 00:05:37,306
let's make sure it really was 0/0,

102
00:05:37,306 --> 00:05:38,889
yep 0/0,

103
00:05:40,993 --> 00:05:43,188
okay so we're dealing
VLANs two and three here,

104
00:05:43,188 --> 00:05:46,021
so I'll make this sub-interface-2 ,

105
00:05:46,021 --> 00:05:48,854
encapsulation dot1q 2,

106
00:05:50,102 --> 00:05:53,102
IP address 2.3.2.3

107
00:05:58,312 --> 00:06:02,062
and then we'll create
a sub-interface vlan-3.

108
00:06:09,262 --> 00:06:10,095
3.2.3.3

109
00:06:11,798 --> 00:06:13,217
and then lastly

110
00:06:13,217 --> 00:06:16,384
we'll bring up our physical interface.

111
00:06:19,386 --> 00:06:21,719
And save that configuration.

112
00:06:24,218 --> 00:06:27,051
Okay, so we're done with router-3.

113
00:06:28,621 --> 00:06:31,134
Now let's go over and
configure the IP addressing

114
00:06:31,134 --> 00:06:33,717
on router-2 here in the middle.

115
00:06:39,239 --> 00:06:43,889
Okay, so let's start with
his fast ethernet 0/1,

116
00:06:43,889 --> 00:06:45,802
so we're not trunking
on these two interfaces,

117
00:06:45,802 --> 00:06:48,220
these are just regular routed ports

118
00:06:48,220 --> 00:06:50,038
with just a single subnet.

119
00:06:50,038 --> 00:06:53,852
So, interface fast ethernet 0/1

120
00:06:53,852 --> 00:06:57,269
that's going to be IP address of 2.3.2.2,

121
00:06:59,626 --> 00:07:01,501
no shut,

122
00:07:01,501 --> 00:07:05,668
and the other one if fast ethernet 1/0,

123
00:07:06,747 --> 00:07:09,747
IP address 3.2.3.2,

124
00:07:11,891 --> 00:07:14,140
no shut.

125
00:07:14,140 --> 00:07:18,825
Okay, and now we have to
configure fast ethernet 0/0

126
00:07:18,825 --> 00:07:20,181
as a trunk.

127
00:07:20,181 --> 00:07:22,136
Now before we do that,

128
00:07:22,136 --> 00:07:26,358
at this point we should have
end-to-end IP connectivity

129
00:07:26,358 --> 00:07:29,412
between router-2 and router-3,

130
00:07:29,412 --> 00:07:31,343
we already previously created the VLANs

131
00:07:31,343 --> 00:07:33,833
and created the trunks in switch-1,

132
00:07:33,833 --> 00:07:35,749
now we've completed our router on a stick

133
00:07:35,749 --> 00:07:37,324
over here on router-3,

134
00:07:37,324 --> 00:07:40,549
and we've configured our
IP addresses on router-2,

135
00:07:40,549 --> 00:07:43,325
so we should be able to ping
our directly connected routers

136
00:07:43,325 --> 00:07:44,957
across that link,

137
00:07:44,957 --> 00:07:46,411
let's see if we can.

138
00:07:46,411 --> 00:07:47,258
If not we have we'll have to

139
00:07:47,258 --> 00:07:49,312
do a little bit of troubleshooting.

140
00:07:49,312 --> 00:07:50,500
So I'm on router-2 right now,

141
00:07:50,500 --> 00:07:53,827
ping 2.3.2.3

142
00:07:53,827 --> 00:07:55,273
he's arping for it,

143
00:07:55,273 --> 00:07:56,822
great, success,

144
00:07:56,822 --> 00:07:59,780
ping 3.2.3.3,

145
00:07:59,780 --> 00:08:01,566
he's arping for it,

146
00:08:01,566 --> 00:08:02,714
and success.

147
00:08:02,714 --> 00:08:03,903
Wonderful.

148
00:08:03,903 --> 00:08:05,904
Okay so now we just have
one little step left

149
00:08:05,904 --> 00:08:08,557
on router-2 we gotta
configure this side over here

150
00:08:08,557 --> 00:08:10,450
as a router on a stick,

151
00:08:10,450 --> 00:08:11,950
by making a trunk.

152
00:08:13,260 --> 00:08:17,427
So interface fast ethernet 0/0.4

153
00:08:19,674 --> 00:08:22,571
to support vlan-4,

154
00:08:22,571 --> 00:08:24,404
encapsulation dot1q 4,

155
00:08:25,886 --> 00:08:28,969
IP address 1.2.4.2,

156
00:08:34,258 --> 00:08:36,675
and sub-interface for vlan-5,

157
00:08:41,311 --> 00:08:43,144
which will be 1.2.5.2,

158
00:08:47,233 --> 00:08:49,650
okay, save the configuration.

159
00:08:51,419 --> 00:08:52,994
Now in this particular case

160
00:08:52,994 --> 00:08:56,832
there are no static routes
necessary on router-2

161
00:08:56,832 --> 00:08:59,764
because every single
subnet in this topology,

162
00:08:59,764 --> 00:09:01,520
he's directly connected to.

163
00:09:01,520 --> 00:09:03,845
There's no subnets here
that he's not actually

164
00:09:03,845 --> 00:09:06,418
connected to on some kind of interface,

165
00:09:06,418 --> 00:09:08,427
so we don't need any kind of static routes

166
00:09:08,427 --> 00:09:09,927
configured on him.

167
00:09:11,163 --> 00:09:13,210
And that concludes this
particular section,

168
00:09:13,210 --> 00:09:16,198
this section was focused
on adding IP addresses

169
00:09:16,198 --> 00:09:19,307
and static routes and we have done that,

170
00:09:19,307 --> 00:09:20,447
so now in the next sections,

171
00:09:20,447 --> 00:09:22,848
we're really gonna get into the meat

172
00:09:22,848 --> 00:09:25,152
of configuring switching commands

173
00:09:25,152 --> 00:09:27,402
on our EtherSwitch routers.

