WEBVTT

0:00:08.060000 --> 0:00:11.700000
 We're going to start adding some
 configuration to these devices.

0:00:11.700000 --> 0:00:14.740000
 So we're going to add IP addresses
 and static routes.

0:00:14.740000 --> 0:00:17.960000
 At this, by the time we're done with
 this particular section, we still

0:00:17.960000 --> 0:00:22.300000
 will not have end-to-end connectivity
 because we haven't completed our

0:00:22.300000 --> 0:00:24.980000
 VLAN configuration and
 spanning tree yet.

0:00:24.980000 --> 0:00:28.920000
 So we will not have end-to-end connectivity
 at the end of this section

0:00:28.920000 --> 0:00:32.940000
 yet. So let's go ahead and add our IP
 addresses and static routes where

0:00:32.940000 --> 0:00:34.220000
 they need to be.

0:00:34.220000 --> 0:00:41.120000
 So let's bring our topology
 diagram back into play.

0:00:41.120000 --> 0:00:44.360000
 And in case you had not already taken
 a screenshot of this, you will want

0:00:44.360000 --> 0:00:47.820000
 to because these are the IP addresses
 we're going to want to implement.

0:00:47.820000 --> 0:00:50.980000
 Now once again, when you're building this,
 you can use whatever IP addressing

0:00:50.980000 --> 0:00:58.040000
 you want. I just chose
 this to make it simple.

0:00:58.040000 --> 0:01:02.220000
 Okay, so I'm going to start with, let's
 start just working from left to

0:01:02.220000 --> 0:01:06.760000
 right. I'll start with router
 one and I will turn him on.

0:01:06.760000 --> 0:01:09.500000
 I've got quite a few devices in this
 topology, so I may not want to turn

0:01:09.500000 --> 0:01:11.200000
 them on. Let's see here.

0:01:11.200000 --> 0:01:13.820000
 Actually, I've only got
 one, two, three, four.

0:01:13.820000 --> 0:01:17.180000
 I've got five iOS devices, so it's probably
 pretty safe to turn them all

0:01:17.180000 --> 0:01:21.080000
 on at once. Okay.

0:01:21.080000 --> 0:01:24.980000
 So let's go ahead and go
 into router one now.

0:01:24.980000 --> 0:01:35.100000
 As that's coming up, it's going to be
 fast ethernet 00 on this particular

0:01:35.100000 --> 0:01:39.000000
 router that we're going to want
 to configure as an 802.1Q trunk.

0:01:39.000000 --> 0:01:42.020000
 So we're basically configuring what's
 called a router on a stick at this

0:01:42.020000 --> 0:01:48.880000
 point. Interface fast ethernet 0 slash
 0, all we have to do here is no

0:01:48.880000 --> 0:01:54.220000
 shut. But before I do that, I'm going
 to want to create my sub interfaces.

0:01:54.220000 --> 0:01:58.700000
 And I'm supporting VLANs four and five,
 so I'll do sub interface four

0:01:58.700000 --> 0:02:00.940000
 to begin with. It could
 be any number I want.

0:02:00.940000 --> 0:02:02.600000
 I'm just choosing that.

0:02:02.600000 --> 0:02:05.560000
 Encapsulation dot one Q four.

0:02:05.560000 --> 0:02:10.420000
 That makes sure that he understands
 802 dot one Q tags and that anything

0:02:10.420000 --> 0:02:14.940000
 that arrives with a tag value of four
 or needs to leave with a tag value

0:02:14.940000 --> 0:02:18.980000
 of four, the VLAN of four, will use
 this particular sub interface.

0:02:18.980000 --> 0:02:22.400000
 And then select the
 correct IP address.

0:02:22.400000 --> 0:02:29.420000
 All right, and then
 rinse and repeat.

0:02:29.420000 --> 0:02:32.460000
 Do the same thing for our
 next sub interface.

0:02:32.460000 --> 0:02:35.900000
 I'm just using the up arrow here
 to go through my command history.

0:02:35.900000 --> 0:02:44.880000
 Just making slight changes
 as we go along.

0:02:44.880000 --> 0:02:48.360000
 Okay, now before I leave this, I also
 need to put in a static route.

0:02:48.360000 --> 0:02:51.760000
 And then the last thing I'll do is
 bring up that physical interface.

0:02:51.760000 --> 0:02:53.600000
 All right, so static route.

0:02:53.600000 --> 0:02:57.920000
 Why don't we just create a single
 default route in this guy?

0:02:57.920000 --> 0:03:00.540000
 Because really there's only
 one way out on him.

0:03:00.540000 --> 0:03:02.800000
 He doesn't have multiple
 egress points.

0:03:02.800000 --> 0:03:06.340000
 So IP route, 0, 0, 0,
 0, 0, 0, 0, 0, 0.

0:03:06.340000 --> 0:03:08.660000
 That says anything you
 don't know about.

0:03:08.660000 --> 0:03:15.360000
 Let's have him go to, well, he's got
 two possible people he could go to.

0:03:15.360000 --> 0:03:21.440000
 VLAN four or VLAN five on his counterpart,
 which is router two.

0:03:21.440000 --> 0:03:23.820000
 So it doesn't really matter.

0:03:23.820000 --> 0:03:25.500000
 We'll just select one of them.

0:03:25.500000 --> 0:03:28.260000
 Let's select in this
 particular case.

0:03:28.260000 --> 0:03:32.540000
 Let's do it this way.

0:03:32.540000 --> 0:03:35.600000
 Let's bring in this drawing here.

0:03:35.600000 --> 0:03:41.360000
 Let's configure router one so that if
 he's trying to get to the 232 network,

0:03:41.360000 --> 0:03:44.820000
 he'll go across VLAN four.

0:03:44.820000 --> 0:03:51.200000
 And if he's trying to get to the 323
 network, he'll go across VLAN five.

0:03:51.200000 --> 0:03:57.120000
 So that will necessitate two different
 static routes in router one.

0:03:57.120000 --> 0:04:03.140000
 All right, so to get
 to the 2.3.2 network.

0:04:03.140000 --> 0:04:07.340000
 Your next hop is going
 to be 1.2.4.2.

0:04:07.340000 --> 0:04:20.220000
 And to get to the 3.2.3 network,
 your next hop will be 1.2.5.2.

0:04:20.220000 --> 0:04:24.440000
 And now the last thing is we need to
 go back into his physical interface

0:04:24.440000 --> 0:04:26.180000
 and bring it up.

0:04:26.180000 --> 0:04:33.140000
 Let's save our configuration.

0:04:33.140000 --> 0:04:36.060000
 Okay, so we are done
 with that router.

0:04:36.060000 --> 0:04:38.520000
 I can get rid of him.

0:04:38.520000 --> 0:04:43.340000
 Now, as far as IP addressing is concerned,
 let's go over to the far right

0:04:43.340000 --> 0:04:45.360000
 and go to router three.

0:04:45.360000 --> 0:04:47.280000
 You can figure out a three.

0:04:47.280000 --> 0:04:50.480000
 It's going to be pretty much the same
 kind of thing as we did in router

0:04:50.480000 --> 0:04:56.140000
 one. So I'll just start by configuring
 my static routes.

0:04:56.140000 --> 0:05:03.820000
 IP route 1.2.4.0, 255.255.255.0.

0:05:03.820000 --> 0:05:09.040000
 And we want that to go to
 the next hop of 2.3.2.2.

0:05:09.040000 --> 0:05:18.000000
 And IP route of 1.2.5.0.

0:05:18.000000 --> 0:05:26.840000
 We want that to go to 3.3.2.3.2.

0:05:26.840000 --> 0:05:30.780000
 Okay, that'll accomplish load
 balancing on that side.

0:05:30.780000 --> 0:05:34.620000
 And then go to interface fast
 ethernet zero slash zero.

0:05:34.620000 --> 0:05:36.800000
 Let's make sure it really
 was zero slash zero.

0:05:36.800000 --> 0:05:38.820000
 Yep, zero slash zero.

0:05:38.820000 --> 0:05:42.840000
 Dot. Okay, so we're dealing with
 VLANs two and three here.

0:05:42.840000 --> 0:05:45.700000
 So I'll make this
 sub interface two.

0:05:45.700000 --> 0:05:48.740000
 Encapsulation dot 1.2.

0:05:48.740000 --> 0:05:57.040000
 IP address 2.3.2.3.

0:05:57.040000 --> 0:06:00.500000
 And then we'll create a sub
 interface VLAN three.

0:06:00.500000 --> 0:06:10.780000
 Three dot two dot three dot three.


0:06:10.780000 --> 0:06:14.820000
 And then lastly, we'll bring
 up our physical interface.

0:06:14.820000 --> 0:06:23.220000
 And save that configuration.

0:06:23.220000 --> 0:06:26.240000
 Okay, so we're done
 with router three.

0:06:26.240000 --> 0:06:31.740000
 Now let's go over and configure the
 IP dressing on router two here in

0:06:31.740000 --> 0:06:43.400000
 the middle. Okay, so let's start with
 his fast ethernet zero slash one.

0:06:43.400000 --> 0:06:45.240000
 So we're not trunking on
 these two interfaces.

0:06:45.240000 --> 0:06:49.960000
 These are just regular routed ports
 with just a single subnet.

0:06:49.960000 --> 0:06:53.200000
 So interface fast ethernet
 zero slash one.

0:06:53.200000 --> 0:06:56.240000
 That's going to be IP address of
 two dot three dot two dot two.

0:06:56.240000 --> 0:07:03.760000
 No shut. And the other one is
 fast ethernet one slash zero.

0:07:03.760000 --> 0:07:09.180000
 IP address three dot two
 dot three dot two.

0:07:09.180000 --> 0:07:18.200000
 No shut. Okay, and now we have to configure
 fast ethernet zero slash zero

0:07:18.200000 --> 0:07:24.380000
 as a trunk. Now before we do that, at
 this point, we should have end to

0:07:24.380000 --> 0:07:29.000000
 end IP connectivity between
 router two and router three.

0:07:29.000000 --> 0:07:32.460000
 We already previously created the VLANs
 and created the trunks in switch

0:07:32.460000 --> 0:07:36.960000
 one. Now we've completed our router on
 a stick over here on router three.

0:07:36.960000 --> 0:07:40.160000
 And we've configured our IP
 addresses on router two.

0:07:40.160000 --> 0:07:43.700000
 So we should be able to ping our directly
 connected routers across that

0:07:43.700000 --> 0:07:48.600000
 link. Let's see if we can.

0:07:48.600000 --> 0:07:52.180000
 So I'm on router two right now, ping
 two dot three dot two dot three.

0:07:52.180000 --> 0:07:54.700000
 He's arping for it.

0:07:54.700000 --> 0:07:59.360000
 Great success. Ping three dot
 two dot three dot three.

0:07:59.360000 --> 0:08:02.240000
 He's arping for it and success.

0:08:02.240000 --> 0:08:06.280000
 Wonderful. Okay, so now we just have
 one little step left on router two.

0:08:06.280000 --> 0:08:10.480000
 We got to configure this side over here
 as a router on a stick by making

0:08:10.480000 --> 0:08:18.180000
 a trunk. So interface fast
 ethernet zero slash zero.

0:08:18.180000 --> 0:08:26.460000
 Four to support VLAN four encapsulation
 dot one Q four IP address one

0:08:26.460000 --> 0:08:41.060000
 dot two dot four dot two and a sub
 interface for VLAN five which will

0:08:41.060000 --> 0:08:48.140000
 be one dot two dot five dot two.

0:08:48.140000 --> 0:08:50.820000
 Okay, save the configuration.

0:08:50.820000 --> 0:08:55.660000
 Now in this particular case there are
 no static routes necessary on router

0:08:55.660000 --> 0:09:00.380000
 two because every single subnet in this
 topology he's directly connected

0:09:00.380000 --> 0:09:04.660000
 to. There's no subnets here that he's
 not actually connected to on some

0:09:04.660000 --> 0:09:06.100000
 kind of interface.

0:09:06.100000 --> 0:09:10.100000
 So we don't need any kind of static
 routes configured on him.

0:09:10.100000 --> 0:09:12.980000
 And that concludes this
 particular section.

0:09:12.980000 --> 0:09:17.060000
 This section was focused on adding
 IP addresses and static routes and

0:09:17.060000 --> 0:09:18.980000
 we have done that.

0:09:18.980000 --> 0:09:22.720000
 So now in the next sections we're really
 going to get into the meat of

0:09:22.720000 --> 0:09:26.780000
 configuring switching commands
 on our ether switch routers.

