WEBVTT

0:00:03.160000 --> 0:00:08.300000
 Hello and welcome to this section on basic
 switching review and configuration.

0:00:08.300000 --> 0:00:12.040000
 So let's just do a real quick review on
 the basics of how layer two switches

0:00:12.040000 --> 0:00:19.280000
 work. So number one, we know the switch
 is essentially a multi port bridge.

0:00:19.280000 --> 0:00:20.400000
 What does that mean?

0:00:20.400000 --> 0:00:25.160000
 That means that its primary job is to
 take in ethernet frames and to look

0:00:25.160000 --> 0:00:29.380000
 at the source and destination MAC address
 of those frames and treat the

0:00:29.380000 --> 0:00:32.560000
 frames accordingly based
 on what it sees.

0:00:32.560000 --> 0:00:33.460000
 So what does that mean?

0:00:33.460000 --> 0:00:37.760000
 Well, it means that number one, we
 forward the frames based on the MAC

0:00:37.760000 --> 0:00:40.520000
 address table. How's the
 MAC address table there?

0:00:40.520000 --> 0:00:42.080000
 How's it built? What's
 it used for?

0:00:42.080000 --> 0:00:43.820000
 Well, once again, a quick review.

0:00:43.820000 --> 0:00:49.320000
 We know that every device in a typical
 switched environment, every device

0:00:49.320000 --> 0:00:50.600000
 has a unique switch port.

0:00:50.600000 --> 0:00:55.000000
 In other words, my laptop is directly
 connected via a cable to its own

0:00:55.000000 --> 0:00:59.480000
 switch port. The laptop next to me, the
 printer next to me, the fax machine

0:00:59.480000 --> 0:01:03.940000
 next to me, they all have their dedicated
 cables connecting in to dedicated

0:01:03.940000 --> 0:01:08.080000
 switch ports. Of course, we're assuming
 a wired network right here.

0:01:08.080000 --> 0:01:15.120000
 So assuming that, then we know that
 the moment that a device sends an

0:01:15.120000 --> 0:01:18.800000
 ethernet frame, the source MAC address
 of that ethernet frame will be

0:01:18.800000 --> 0:01:19.560000
 learned by the switch.

0:01:19.560000 --> 0:01:22.720000
 The switch will see that MAC address
 frame as it comes in, it'll go into

0:01:22.720000 --> 0:01:25.500000
 its MAC address table and say, oh, I've
 never seen this MAC address frame

0:01:25.500000 --> 0:01:27.320000
 before. This is brand new.

0:01:27.320000 --> 0:01:32.040000
 And so take the MAC address, the port
 that it came in on, and the VLAN

0:01:32.040000 --> 0:01:36.520000
 that port is associated to and learn
 that into the MAC address table.

0:01:36.520000 --> 0:01:40.100000
 And then that entry will stay in the
 MAC address table for a variety of

0:01:40.100000 --> 0:01:44.140000
 reasons. Number one, if that MAC address
 is active, if it's pretty periodically

0:01:44.140000 --> 0:01:48.240000
 sending stuff, that entry will
 stay in the MAC address table.

0:01:48.240000 --> 0:01:53.960000
 If that MAC address goes dormant or silent,
 like let's say that my laptop

0:01:53.960000 --> 0:01:59.100000
 just was connected to the switch, but didn't
 send anything, just was completely

0:01:59.100000 --> 0:02:01.140000
 idle and didn't send anything.

0:02:01.140000 --> 0:02:04.080000
 Well, then that MAC address would eventually
 age out of the MAC address

0:02:04.080000 --> 0:02:08.720000
 table. And you should remember that that's
 for five minutes or 300 seconds.

0:02:08.720000 --> 0:02:13.500000
 So 300 seconds is the inactivity or
 the aging timer of MAC addresses in

0:02:13.500000 --> 0:02:14.840000
 the MAC address table.

0:02:14.840000 --> 0:02:17.320000
 Thirdly, if the port goes down.

0:02:17.320000 --> 0:02:22.280000
 So if I disconnect my laptop and move
 away, once that port detects it's

0:02:22.280000 --> 0:02:26.840000
 electrically not connected to anything
 anymore, then any and all MAC addresses

0:02:26.840000 --> 0:02:30.480000
 that were associated to that port are
 wiped out of the MAC address table.

0:02:30.480000 --> 0:02:32.100000
 So that's the learning process.

0:02:32.100000 --> 0:02:33.860000
 The forwarding process
 is very similar.

0:02:33.860000 --> 0:02:36.760000
 An Ethernet frame comes in and now
 the switch looks at the destination

0:02:36.760000 --> 0:02:40.520000
 MAC address. Looks at that destination
 MAC address, goes into the MAC

0:02:40.520000 --> 0:02:43.100000
 address table, tries to find
 a corresponding hit.

0:02:43.100000 --> 0:02:46.740000
 If it does find a match, then let's
 forward that Ethernet frame out the

0:02:46.740000 --> 0:02:48.740000
 port where it needs to go.

0:02:48.740000 --> 0:02:52.520000
 If it doesn't find a match, then that
 frame will be flooded and be flooded

0:02:52.520000 --> 0:02:57.340000
 out. All other ports are in the
 same VLAN as the ingress port.

0:02:57.340000 --> 0:03:02.000000
 We know that switches separate
 collision domains.

0:03:02.000000 --> 0:03:05.640000
 Once again, this is a review
 of what that's talking about.

0:03:05.640000 --> 0:03:07.260000
 That means that.

0:03:07.260000 --> 0:03:15.840000
 I could have something like this.

0:03:15.840000 --> 0:03:20.180000
 And these two laptops
 laptop A and B.

0:03:20.180000 --> 0:03:25.420000
 They could send frames at exactly
 the same time into that switch.

0:03:25.420000 --> 0:03:29.480000
 And unlike a hub where this would be
 a problem and those frames would

0:03:29.480000 --> 0:03:33.520000
 cause a collision and they'd have to be
 retransmitted in a switched environment.

0:03:33.520000 --> 0:03:36.980000
 That's not the case because if you recall
 from some of my earlier courses,

0:03:36.980000 --> 0:03:40.500000
 switches have memory associated
 to their interfaces.

0:03:40.500000 --> 0:03:44.500000
 And so this memory can store
 and buffer these frames.

0:03:44.500000 --> 0:03:48.360000
 So frames can be coming in multiple
 switch ports all simultaneously all

0:03:48.360000 --> 0:03:52.900000
 day long and the switch will buffer
 those frames and then each one one

0:03:52.900000 --> 0:03:56.580000
 by one will be looked up and sent
 out to where it needs to go.

0:03:56.580000 --> 0:04:02.360000
 Now, normally your connection to a switch
 is in full duplex mode, which

0:04:02.360000 --> 0:04:06.240000
 means that you can transmit at exactly the
 same time the switch is transmitting

0:04:06.240000 --> 0:04:10.600000
 to you. Because if you remember the
 basics of ethernet cabling with an

0:04:10.600000 --> 0:04:19.140000
 ethernet cable, we had something like
 this where your transmit, like if

0:04:19.140000 --> 0:04:22.760000
 this was transmit on your side for
 transmitting ones and zeros, ended

0:04:22.760000 --> 0:04:28.080000
 up being received on the other side
 of the cable and his transmit pin,

0:04:28.080000 --> 0:04:31.840000
 his transmit wire
 was your receive.

0:04:31.840000 --> 0:04:35.620000
 So you're actually using so if I'm transmitting
 this way and he's transmitting

0:04:35.620000 --> 0:04:41.100000
 this way, we're actually using completely
 separate strands of copper cable

0:04:41.100000 --> 0:04:43.740000
 inside our main ethernet cable.

0:04:43.740000 --> 0:04:45.540000
 They're not going to
 run into each other.

0:04:45.540000 --> 0:04:51.680000
 Now, in the unlikely event that one or
 both of these devices is configured

0:04:51.680000 --> 0:04:57.080000
 for half duplex, well then
 they can't do this.

0:04:57.080000 --> 0:05:00.620000
 In half duplex mode only one
 side can talk at a time.

0:05:00.620000 --> 0:05:04.060000
 And if they did this, if the switch
 was transmitting to me at exactly

0:05:04.060000 --> 0:05:08.660000
 the same time I was transmitting to him,
 that would be considered a collision.

0:05:08.660000 --> 0:05:12.340000
 Now why they say that switch is separate
 collision domains is because

0:05:12.340000 --> 0:05:17.120000
 if there's any collisions here,
 it does not affect PCB.

0:05:17.120000 --> 0:05:20.920000
 PCB can still be transmitting all day
 long because his connection to the

0:05:20.920000 --> 0:05:25.000000
 switch isn't a completely
 separate collision domain.

0:05:25.000000 --> 0:05:28.360000
 So any collisions that happen here are
 completely independent from collisions

0:05:28.360000 --> 0:05:29.220000
 that happen here.

0:05:29.220000 --> 0:05:33.540000
 So each switch port, if collisions
 happen on it, which they shouldn't,

0:05:33.540000 --> 0:05:39.280000
 will not affect any of the other
 ports on that same switch.

0:05:39.280000 --> 0:05:44.660000
 And layer two switches operate
 at the data link layer.

0:05:44.660000 --> 0:05:48.160000
 However, the reality is that most of
 the switches you can purchase these

0:05:48.160000 --> 0:05:51.900000
 days are what we call multi-layer switches,
 which means they can not only

0:05:51.900000 --> 0:05:55.480000
 look at MAC addresses to make their
 forwarding decisions, they can also

0:05:55.480000 --> 0:05:56.360000
 look higher than that.

0:05:56.360000 --> 0:06:00.600000
 They can look at the IP addresses,
 they can even look at TCP UDP port

0:06:00.600000 --> 0:06:03.520000
 numbers to make forward
 or filtering decisions.

0:06:03.520000 --> 0:06:06.100000
 That's what we mean by
 a multi-layer switch.

0:06:06.100000 --> 0:06:09.080000
 All right, so let's just do a quick
 review here on some of the basics

0:06:09.080000 --> 0:06:11.180000
 of configuring a switch.

0:06:11.180000 --> 0:06:15.940000
 All right, so there's
 nothing new here.

0:06:15.940000 --> 0:06:20.140000
 We've already talked about the MACRS
 table and basically how it works.

0:06:20.140000 --> 0:06:23.780000
 So some initial configuration
 commands.

0:06:23.780000 --> 0:06:26.820000
 You're probably going to want to put
 a host name on your switch, enable

0:06:26.820000 --> 0:06:30.080000
 password. You might want to put some
 sort of banners to give some sort

0:06:30.080000 --> 0:06:33.680000
 of descriptive warning like this switch
 belongs to engineering department.

0:06:33.680000 --> 0:06:38.000000
 Keep out. Or if you have any problems
 on this switch, call Ken, the network

0:06:38.000000 --> 0:06:40.320000
 admin or whatever it
 might happen to be.

0:06:40.320000 --> 0:06:43.460000
 You're probably also going to want
 to type in no IP domain lookup and

0:06:43.460000 --> 0:06:47.080000
 logging synchronous, which are not
 necessary, but certainly make your

0:06:47.080000 --> 0:06:51.100000
 life a lot more convenient
 if you do that.

0:06:51.100000 --> 0:06:54.560000
 And then of course you can do show IP
 interface brief because different

0:06:54.560000 --> 0:06:58.300000
 switches have different naming
 conventions on their ports.

0:06:58.300000 --> 0:06:59.440000
 What do I mean by that?

0:06:59.440000 --> 0:07:02.660000
 Well, for example, some switches
 have 10, 100 interfaces.

0:07:02.660000 --> 0:07:05.980000
 So their ports might start out
 as fast Ethernet something.

0:07:05.980000 --> 0:07:08.880000
 A lot of other switches might just
 have gigabit Ethernet ports.

0:07:08.880000 --> 0:07:10.220000
 So you'll need to know that.

0:07:10.220000 --> 0:07:12.560000
 Or if I'm going to put an IP address
 on an interface, I have to know do

0:07:12.560000 --> 0:07:16.500000
 I start out interface fast Ethernet something,
 interface gigabit Ethernet

0:07:16.500000 --> 0:07:18.000000
 something, you know, what is it?

0:07:18.000000 --> 0:07:19.980000
 Also the numbering convention.

0:07:19.980000 --> 0:07:24.620000
 Some switches have a number, a slash,
 a number like gigabit zero slash

0:07:24.620000 --> 0:07:26.640000
 one or something like that.

0:07:26.640000 --> 0:07:29.560000
 Other switches, especially switches that
 you'll find that can stack together

0:07:29.560000 --> 0:07:31.000000
 in a switching stack.

0:07:31.000000 --> 0:07:34.140000
 A lot of times we'll have three digits
 in their interface numbering like

0:07:34.140000 --> 0:07:37.920000
 gigabit zero slash zero slash
 one or something like that.

0:07:37.920000 --> 0:07:42.140000
 So by doing show IP interface brief,
 you can very quickly learn how does

0:07:42.140000 --> 0:07:44.960000
 this switch view its interfaces?

0:07:44.960000 --> 0:07:50.140000
 How does it name its interfaces?

0:07:50.140000 --> 0:07:57.160000
 Okay, so switch ports by default
 don't support IP addressing.

0:07:57.160000 --> 0:08:01.220000
 They only support the forwarding
 of Ethernet frames.

0:08:01.220000 --> 0:08:06.540000
 So if you want to put an IP address
 on your switch and you probably will

0:08:06.540000 --> 0:08:09.260000
 see you can tell that to
 it so you can ping it.

0:08:09.260000 --> 0:08:13.520000
 There's a couple of places
 that you can do that.

0:08:13.520000 --> 0:08:17.200000
 Let me just show you
 real quickly here.

0:08:17.200000 --> 0:08:20.120000
 So here's my switch.

0:08:20.120000 --> 0:08:24.780000
 Here are a couple of
 ports on that switch.

0:08:24.780000 --> 0:08:29.120000
 Let's say zero slash one zero
 slash two and so forth.

0:08:29.120000 --> 0:08:36.800000
 Okay, so by default, if I try to put an
 IP address on any of those physical

0:08:36.800000 --> 0:08:39.120000
 interfaces, it won't let me.

0:08:39.120000 --> 0:08:44.100000
 So let's say that all these interfaces
 here were in one broadcast domain.

0:08:44.100000 --> 0:08:46.980000
 Let's just say it was VLAN two.

0:08:46.980000 --> 0:08:51.160000
 Okay, and as a network administrator,
 I decide that everything that was

0:08:51.160000 --> 0:08:54.460000
 in that broadcast domain that was in
 VLAN two was going to be in the two

0:08:54.460000 --> 0:08:59.180000
 dot two dot two dot zero slash
 twenty four network.

0:08:59.180000 --> 0:09:05.100000
 All right. Well, if I want the devices
 in this VLAN to be able to access

0:09:05.100000 --> 0:09:09.940000
 the switch, ping it, tell net to it,
 SSH to it, I need to give this switch

0:09:09.940000 --> 0:09:14.020000
 an address in the two to two
 network so they can reach it.

0:09:14.020000 --> 0:09:15.860000
 I need to give them
 a host address.

0:09:15.860000 --> 0:09:26.540000
 So one way is I can create what's called
 a switched virtual interface.

0:09:26.540000 --> 0:09:32.140000
 A logical interface cables
 don't plug into it.

0:09:32.140000 --> 0:09:34.760000
 It's kind of like a, like
 our VTY lines, right?

0:09:34.760000 --> 0:09:37.140000
 We were dealing with
 telnet or SSH.

0:09:37.140000 --> 0:09:39.160000
 A VTY line is not
 a physical thing.

0:09:39.160000 --> 0:09:40.200000
 You can't see it.

0:09:40.200000 --> 0:09:43.660000
 If you're looking at a router switch,
 it's a placeholder for your SSH

0:09:43.660000 --> 0:09:46.340000
 and telnet configuration commands.


0:09:46.340000 --> 0:09:50.780000
 Well, switch virtual interface is
 similarly a logical interface.

0:09:50.780000 --> 0:09:53.280000
 So we just say interface.

0:09:53.280000 --> 0:09:56.920000
 So we have to go into global configuration
 mode first config T and then

0:09:56.920000 --> 0:10:02.340000
 we say interface VLAN
 in this case VLAN two.

0:10:02.340000 --> 0:10:06.080000
 I want to create a switched virtual
 interface for this particular VLAN.

0:10:06.080000 --> 0:10:10.820000
 Then they'll drop you down into config
 dash IF mode interface mode.

0:10:10.820000 --> 0:10:13.260000
 And here I can put my IP address.

0:10:13.260000 --> 0:10:17.600000
 And of course, don't forget
 about your subnet mask.

0:10:17.600000 --> 0:10:25.100000
 And don't forget to do your
 no shutdown command.

0:10:25.100000 --> 0:10:26.540000
 So that's one place.

0:10:26.540000 --> 0:10:28.840000
 You can place an IP address.

0:10:28.840000 --> 0:10:32.960000
 And if your primary objective is, hey,
 I want this switch to have a host

0:10:32.960000 --> 0:10:35.440000
 address in this broadcast domain.

0:10:35.440000 --> 0:10:37.240000
 There's a broadcast domain.

0:10:37.240000 --> 0:10:39.940000
 There's got a whole bunch of hosts in
 it and he needs an address as well.

0:10:39.940000 --> 0:10:42.460000
 That's perfectly acceptable
 to do it that way.

0:10:42.460000 --> 0:10:49.840000
 Another method you could do is we could
 change actually the physical interface

0:10:49.840000 --> 0:10:54.540000
 to the point where it will allow
 us to put in an IP address.

0:10:54.540000 --> 0:11:01.860000
 So for example, let's say that this
 interface right here was connecting

0:11:01.860000 --> 0:11:09.060000
 to a server. And he was going to
 be three, three, three, one.

0:11:09.060000 --> 0:11:12.640000
 Let's say slash 30.

0:11:12.640000 --> 0:11:20.100000
 Okay. We want his default gateway
 to be three, three, three, two.

0:11:20.100000 --> 0:11:23.940000
 That's the only other available
 address in that network.

0:11:23.940000 --> 0:11:25.860000
 And we want that to be the switch.


0:11:25.860000 --> 0:11:27.520000
 The switch is capable of routing.

0:11:27.520000 --> 0:11:29.360000
 This is a multi-layer switch.

0:11:29.360000 --> 0:11:32.080000
 So we want him to be the
 default gateway for this.

0:11:32.080000 --> 0:11:34.480000
 The server here.

0:11:34.480000 --> 0:11:37.460000
 Well, certainly I could take
 the same approach I just did.

0:11:37.460000 --> 0:11:40.500000
 I could put that interface zero slash
 four into a different broadcast

0:11:40.500000 --> 0:11:43.820000
 domain. I could put into
 VLAN three maybe.

0:11:43.820000 --> 0:11:48.380000
 And then on that switch, I could say
 interface VLAN three and put my IP

0:11:48.380000 --> 0:11:50.600000
 address of three, three,
 three, two right there.

0:11:50.600000 --> 0:11:52.560000
 Or alternatively, I could do this.


0:11:52.560000 --> 0:11:54.400000
 I could go on to this
 interface right here.

0:11:54.400000 --> 0:11:58.920000
 So let's say it's a fast ethernet interface
 interface, fast ethernet zero

0:11:58.920000 --> 0:12:04.180000
 slash four. And I could
 say no switch port.

0:12:04.180000 --> 0:12:09.600000
 When you type the command, no switch
 port, you're telling the interface,

0:12:09.600000 --> 0:12:15.140000
 hey, you are no longer one of a
 group of interfaces in a VLAN.

0:12:15.140000 --> 0:12:19.080000
 It's no longer your job to switch stuff
 back and forth like other switching

0:12:19.080000 --> 0:12:23.320000
 ports. You are now a routed port.

0:12:23.320000 --> 0:12:26.100000
 You are now a port
 like a router has.

0:12:26.100000 --> 0:12:27.160000
 Think about port.

0:12:27.160000 --> 0:12:28.860000
 Now we don't call them
 ports on routers.

0:12:28.860000 --> 0:12:30.300000
 We call them interfaces.

0:12:30.300000 --> 0:12:32.640000
 But think about interfaces
 on routers, right?

0:12:32.640000 --> 0:12:35.540000
 One interface on a router
 expects an IP address.

0:12:35.540000 --> 0:12:40.640000
 He is a host in a particular network
 and he can route packets in and out

0:12:40.640000 --> 0:12:42.040000
 of that network.

0:12:42.040000 --> 0:12:43.020000
 Same thing here.

0:12:43.020000 --> 0:12:48.520000
 Now that I've done no switch port, I
 can actually put my IP address right

0:12:48.520000 --> 0:12:53.160000
 on that interface, right on the
 physical interface itself.

0:12:53.160000 --> 0:12:58.520000
 And I can do a no shut.

0:12:58.520000 --> 0:13:02.440000
 So that's the other way.

0:13:02.440000 --> 0:13:04.700000
 You can put an IP address
 on your switch.

0:13:04.700000 --> 0:13:08.340000
 Whether it be a switch virtual interface
 or whether you put on a routed

0:13:08.340000 --> 0:13:16.060000
 port like I've just done right
 here, either method will work.

0:13:16.060000 --> 0:13:27.260000
 All right. So we've talked about
 switch virtual interfaces.

0:13:27.260000 --> 0:13:34.260000
 There we have one.

0:13:34.260000 --> 0:13:38.300000
 If you do not plan on doing any kind
 of routing on your switch, if your

0:13:38.300000 --> 0:13:42.620000
 switch is going to be a pure layer to
 switch and the only reason you're

0:13:42.620000 --> 0:13:45.740000
 putting an IP address on there
 is so that you can ping it.

0:13:45.740000 --> 0:13:47.980000
 You can tell that to it, but
 you're not going to route it.

0:13:47.980000 --> 0:13:50.440000
 It's not going to
 know how to route.

0:13:50.440000 --> 0:13:52.160000
 Then just like your laptop, right?


0:13:52.160000 --> 0:13:54.340000
 Your laptop doesn't
 know how to route.

0:13:54.340000 --> 0:13:56.360000
 It needs a default gateway.

0:13:56.360000 --> 0:14:00.180000
 In this case, a switch also would need
 a default gateway if you're not

0:14:00.180000 --> 0:14:06.140000
 going to configure routing or if
 he's not capable of routing.

0:14:06.140000 --> 0:14:11.160000
 And of course, we can use ping or trace
 route or various show commands

0:14:11.160000 --> 0:14:15.700000
 to configure or to verify our
 existing configuration.

0:14:15.700000 --> 0:14:20.100000
 So let's just look at some quick configuration
 examples right here.

0:14:20.100000 --> 0:14:23.300000
 So right now we're looking at the switch
 and we're paying attention to

0:14:23.300000 --> 0:14:24.660000
 this interface right here.

0:14:24.660000 --> 0:14:28.880000
 How do we configure that interface
 if he's connecting to a host?

0:14:28.880000 --> 0:14:31.260000
 Well, you probably want
 to give him a host name.

0:14:31.260000 --> 0:14:33.080000
 Then we go on to that interface.

0:14:33.080000 --> 0:14:36.200000
 That's gig one, zero
 is five right there.

0:14:36.200000 --> 0:14:37.920000
 You can give him a description.

0:14:37.920000 --> 0:14:38.580000
 That's optional.

0:14:38.580000 --> 0:14:42.280000
 You don't have to do that, but you can
 do that to make it more meaningful

0:14:42.280000 --> 0:14:45.120000
 when you're looking at the config as
 to what does that interface connect

0:14:45.120000 --> 0:14:46.520000
 to? Well, there's the description.


0:14:46.520000 --> 0:14:49.980000
 It tells you. And the main command
 here I want to point out is switch

0:14:49.980000 --> 0:14:52.480000
 port mode access.

0:14:52.480000 --> 0:14:56.420000
 So when you say switch port mode access,
 that means this interface right

0:14:56.420000 --> 0:15:00.180000
 here is only going
 to be in one VLAN.

0:15:00.180000 --> 0:15:04.420000
 Now, notice in this configuration right
 here, there's no mention of what

0:15:04.420000 --> 0:15:10.020000
 that VLAN is. So if we don't see it,
 if you do a show run and you see

0:15:10.020000 --> 0:15:13.280000
 switch port mode access, but on this
 particular interface, there's no

0:15:13.280000 --> 0:15:14.600000
 mention of what the VLAN is.

0:15:14.600000 --> 0:15:18.320000
 It will be in the default
 VLAN in VLAN one.

0:15:18.320000 --> 0:15:23.960000
 And then of course, no shutdown, which
 might be the default anyway, but

0:15:23.960000 --> 0:15:26.440000
 no harm in doing that.

0:15:26.440000 --> 0:15:29.560000
 So that's our interface
 leading to our host.

0:15:29.560000 --> 0:15:33.720000
 Now, if we go a little bit further,
 now we say, okay, now I want to look

0:15:33.720000 --> 0:15:37.580000
 at his interface leading into the core
 of the network, his interface leading

0:15:37.580000 --> 0:15:39.600000
 to another switch.

0:15:39.600000 --> 0:15:45.360000
 So now we're looking at interface
 gig one, zero, one.

0:15:45.360000 --> 0:15:50.560000
 So same thing, you might want
 to put a description on it.

0:15:50.560000 --> 0:15:55.300000
 And this command right here, switch
 port mode dynamic desirable.

0:15:55.300000 --> 0:15:56.640000
 What does this do?

0:15:56.640000 --> 0:16:03.540000
 This activates a Cisco proprietary protocol
 called DTP, which we'll talk

0:16:03.540000 --> 0:16:04.880000
 about in just a few minutes.

0:16:04.880000 --> 0:16:08.340000
 But essentially what this is doing
 is just saying, hey, I'm allowed to

0:16:08.340000 --> 0:16:11.760000
 form a VLAN trunk if the other
 side is okay with it.

0:16:11.760000 --> 0:16:16.640000
 If the other side of this link also
 does DTP and can exchange some DTP

0:16:16.640000 --> 0:16:20.820000
 messages with me, then we can
 go ahead and form a trunk.

0:16:20.820000 --> 0:16:25.520000
 If there is no DTP exchange, I would
 just stay as an access port.

0:16:25.520000 --> 0:16:28.740000
 In this case, in the default VLAN,
 because we don't see any mention of

0:16:28.740000 --> 0:16:35.900000
 VLAN. So if both of these links here
 are configured as switch port mode

0:16:35.900000 --> 0:16:40.440000
 dynamic desirable, they
 will form a VLAN trunk.

0:16:40.440000 --> 0:16:45.620000
 And then no shutdown, no shutdown
 once again as a, just a safeguard.

0:16:45.620000 --> 0:16:51.940000
 And then here we see the other side
 of the link here we see switch two,

0:16:51.940000 --> 0:16:57.740000
 which is just a mirror image
 of what we saw in switch one.

0:16:57.740000 --> 0:17:03.340000
 Okay, a lot of times you will want to
 apply the same set of configuration

0:17:03.340000 --> 0:17:06.320000
 commands across a range
 of interfaces.

0:17:06.320000 --> 0:17:10.080000
 Like let's say you want to get on 10
 interfaces and you want to do switch

0:17:10.080000 --> 0:17:13.000000
 port mode dynamic desirable
 on all of them.

0:17:13.000000 --> 0:17:20.800000
 Okay. So within switches, you can use
 the interface range command to do

0:17:20.800000 --> 0:17:23.200000
 that. So here's how we can see it.


0:17:23.200000 --> 0:17:27.620000
 So we're at global configuration
 mode, we say interface range.

0:17:27.620000 --> 0:17:29.780000
 And here's how you
 specify your range.

0:17:29.780000 --> 0:17:34.820000
 If you're going to do a range of continuous
 or contiguous interfaces like

0:17:34.820000 --> 0:17:39.520000
 fast ethernet zero slash one through
 seven, then you just use a hyphen.

0:17:39.520000 --> 0:17:44.520000
 Right. So the hyphen means they are
 all fast ethernet and interface zero

0:17:44.520000 --> 0:17:47.400000
 one all the way up to
 zero slash seven.

0:17:47.400000 --> 0:17:52.680000
 If you want to include in your interface
 range and interface that's not

0:17:52.680000 --> 0:17:56.400000
 contiguous, then you
 use the comma.

0:17:56.400000 --> 0:18:01.120000
 And after the comma, you have to again
 specify the type of interface.

0:18:01.120000 --> 0:18:04.680000
 So for example, if I said interface
 range fast ethernet zero slash one

0:18:04.680000 --> 0:18:10.780000
 hyphen seven comma zero slash twelve,
 it would give me an error message.

0:18:10.780000 --> 0:18:15.280000
 Because maybe the switch has a gig interface
 of zero slash twelve as well

0:18:15.280000 --> 0:18:18.180000
 as a fast ethernet interface
 of zero slash twelve.

0:18:18.180000 --> 0:18:21.100000
 It wouldn't know which one
 to include in the range.

0:18:21.100000 --> 0:18:25.480000
 So when you have a comma, you have
 to specify the type of interface as

0:18:25.480000 --> 0:18:28.280000
 well as the number after that.

0:18:28.280000 --> 0:18:34.480000
 And so now at this point, it puts
 me into the interface range mode.

0:18:34.480000 --> 0:18:38.940000
 And now anything I type in at this point
 will apply across all this range

0:18:38.940000 --> 0:18:42.640000
 of interfaces. Like in this case,
 I'm bringing them all up.

0:18:42.640000 --> 0:18:43.980000
 I did no shutdown.

0:18:43.980000 --> 0:18:48.260000
 I'm converting them
 all to access ports.

0:18:48.260000 --> 0:18:51.340000
 Some routers will
 also support that.

0:18:51.340000 --> 0:18:55.080000
 So if you want to configure range of
 fast ethernet or gig of it, ethernet

0:18:55.080000 --> 0:19:03.980000
 interfaces on a router,
 go ahead and try it.

0:19:03.980000 --> 0:19:08.540000
 For example, maybe not a lot at layer
 two, but for talking about routing.

0:19:08.540000 --> 0:19:12.500000
 Right. Maybe at layer three, I want
 to go on to four interfaces on my

0:19:12.500000 --> 0:19:15.500000
 router and put them all
 into OSPF area zero.

0:19:15.500000 --> 0:19:20.300000
 I want to apply EIGRP authentication
 across all those interfaces at once.

0:19:20.300000 --> 0:19:23.760000
 That would be a good use of using the
 interface range command on a series

0:19:23.760000 --> 0:19:29.300000
 of router interfaces.

0:19:29.300000 --> 0:19:33.900000
 Viewing the MAC address table, primary
 command is show MAC address dash

0:19:33.900000 --> 0:19:38.840000
 table. And these ones here are ones that
 you should definitely be familiar

0:19:38.840000 --> 0:19:44.540000
 with. The output of those commands and
 what you will see from those commands.

0:19:44.540000 --> 0:19:51.260000
 Probably unlikely that you will ever
 add a static entry to the MAC address

0:19:51.260000 --> 0:19:53.800000
 table, but it is possible
 to do that.

0:19:53.800000 --> 0:19:57.980000
 So in that case, it's just MAC
 address dash table static.

0:19:57.980000 --> 0:20:03.160000
 Once you type that in, you follow
 it with the MAC address you want.

0:20:03.160000 --> 0:20:05.060000
 The interface name and number.

0:20:05.060000 --> 0:20:08.820000
 So you'd actually say like interface
 gigabit zero slash one, and then

0:20:08.820000 --> 0:20:11.720000
 the VLAN, the VLAN number.

0:20:11.720000 --> 0:20:17.060000
 And for basic troubleshooting,
 things aren't working right.

0:20:17.060000 --> 0:20:17.920000
 Check the cable type.

0:20:17.920000 --> 0:20:19.480000
 Remember, right?

0:20:19.480000 --> 0:20:21.200000
 Similar to similar, right?

0:20:21.200000 --> 0:20:24.860000
 Switch to switch requires
 crossover cable.

0:20:24.860000 --> 0:20:29.420000
 This similar device is like switch to
 router requires a straight through

0:20:29.420000 --> 0:20:33.420000
 cable. So make sure you got
 the correct cable type.

0:20:33.420000 --> 0:20:36.400000
 Ensure the interface is not
 administratively down.

0:20:36.400000 --> 0:20:42.160000
 Make sure the no shutdown
 command was typed in.

0:20:42.160000 --> 0:20:45.720000
 For access ports check
 for the same VLAN.

0:20:45.720000 --> 0:20:51.680000
 So if I have two hosts, they're saying,
 hey, we're both in the 10 network.

0:20:51.680000 --> 0:20:52.980000
 I'm 10, 1, 1, 1.

0:20:52.980000 --> 0:20:54.520000
 I'm 10, 1, 1, 2.

0:20:54.520000 --> 0:20:56.820000
 We should be able to talk to
 each other, but we can't.

0:20:56.820000 --> 0:20:58.900000
 Well, make sure those two hosts
 are in the same VLAN.

0:20:58.900000 --> 0:21:03.260000
 Otherwise, they won't be
 able to communicate.

0:21:03.260000 --> 0:21:06.200000
 And verify DTP compatibility
 modes.

0:21:06.200000 --> 0:21:09.220000
 We'll talk a little bit more about
 that in just one moment.

0:21:09.220000 --> 0:21:16.100000
 All right. So that is it for basic switching
 and basic switching configuration

0:21:16.100000 --> 0:21:19.820000
 review. Thank you so much for
 watching this recording.

