WEBVTT

0:00:03.260000 --> 0:00:06.940000
 Hello and welcome to this video in which
 we're going to go over configuring

0:00:06.940000 --> 0:00:11.540000
 dynamic ARP inspection and
 monitoring it in Cisco iOS.

0:00:11.540000 --> 0:00:16.280000
 So that is our goal here.

0:00:16.280000 --> 0:00:18.240000
 Let's go ahead and
 check in with this.

0:00:18.240000 --> 0:00:21.460000
 So with dynamic ARP inspection, there's
 only two commands you need to

0:00:21.460000 --> 0:00:25.720000
 do. Number one, you need to enable it
 globally on the VLAN or VLANs that

0:00:25.720000 --> 0:00:29.880000
 you wish. And remember that will make
 all the ports in that VLAN untrusted

0:00:29.880000 --> 0:00:34.740000
 from the perspective of ARP
 requests and ARP replies.

0:00:34.740000 --> 0:00:37.920000
 So every ARP request and reply coming
 in a port in that VLAN will have

0:00:37.920000 --> 0:00:42.460000
 to be paused and inspected against
 the DHCP snooping binding database.

0:00:42.460000 --> 0:00:46.280000
 Secondly, if you have devices connected
 to your switch to have static

0:00:46.280000 --> 0:00:49.920000
 IP addresses like your routers, your
 servers, you probably want to go

0:00:49.920000 --> 0:00:55.420000
 to their interfaces and make
 them as trusted interfaces.

0:00:55.420000 --> 0:01:01.480000
 Okay, I gave an example in the previous
 video about a situation where

0:01:01.480000 --> 0:01:06.820000
 a single physical interface could lead
 to some devices with static IP

0:01:06.820000 --> 0:01:12.280000
 addresses and some devices that are either
 unknown or have DHCP, but either

0:01:12.280000 --> 0:01:18.160000
 way, where there would be a risk of making
 that interface, trusted interface.

0:01:18.160000 --> 0:01:21.940000
 And I said, in that particular scenario,
 you'd want to use an ARP access

0:01:21.940000 --> 0:01:25.000000
 list. And that's what I want
 to talk about right here.

0:01:25.000000 --> 0:01:29.940000
 So here we say we ARP access dash list
 and you give it a descriptive name.

0:01:29.940000 --> 0:01:33.640000
 And you can say, permit IP host, you
 give the IP address of the device

0:01:33.640000 --> 0:01:38.680000
 with a static IP address, Mac host,
 you give the Mac address of that,

0:01:38.680000 --> 0:01:40.760000
 the NIC card on that device.

0:01:40.760000 --> 0:01:46.220000
 And then the last step is we want to
 associate this ARP access list with

0:01:46.220000 --> 0:01:48.480000
 dynamic ARP inspection.

0:01:48.480000 --> 0:01:54.920000
 So here in applying it, we would say
 IP ARP inspection filter and then

0:01:54.920000 --> 0:01:58.980000
 give it the name of the ARP access list
 and apply it to a particular VLAN.

0:01:58.980000 --> 0:02:02.060000
 Now, notice that at the end here,
 there's this keyword of static.

0:02:02.060000 --> 0:02:03.080000
 What does that do?

0:02:03.080000 --> 0:02:06.180000
 All right, you're probably not going
 to want to use the keyword of static.

0:02:06.180000 --> 0:02:08.580000
 So you probably want
 to leave that off.

0:02:08.580000 --> 0:02:14.640000
 So if you don't include that keyword,
 what that will mean is that now,

0:02:14.640000 --> 0:02:25.800000
 what an ARP request or an ARP reply is
 received on an untrusted interface.

0:02:25.800000 --> 0:02:29.960000
 The first thing that will happen is
 we'll see if we can validate that

0:02:29.960000 --> 0:02:33.140000
 request or reply against
 your ARP access list.

0:02:33.140000 --> 0:02:36.620000
 We'll see, is there a permit entry or
 maybe a deny entry if you're denying

0:02:36.620000 --> 0:02:39.940000
 something? If there's a permit
 entry, we're done.

0:02:39.940000 --> 0:02:42.480000
 We can go ahead and
 allow it on through.

0:02:42.480000 --> 0:02:49.160000
 If there's no entry in here, then we
 will fall back to the DHCP snooping

0:02:49.160000 --> 0:02:50.200000
 binding database.

0:02:50.200000 --> 0:02:54.960000
 And we'll try to validate the ARP request
 or reply there before we decide

0:02:54.960000 --> 0:02:56.720000
 to drop or forward it.

0:02:56.720000 --> 0:03:01.900000
 Now, in the event that you
 decide, hey, you know what?

0:03:01.900000 --> 0:03:06.860000
 I like this ARP, you know, dynamic
 ARP inspection thing, but I really

0:03:06.860000 --> 0:03:09.680000
 don't have a use for
 DHCP snooping.

0:03:09.680000 --> 0:03:15.400000
 You know, maybe everything on my switch
 has got static IP addresses.

0:03:15.400000 --> 0:03:19.180000
 So I'm not going to have a DHCP snooping
 binding database because I'm

0:03:19.180000 --> 0:03:21.480000
 not using DHCP snooping.

0:03:21.480000 --> 0:03:25.400000
 That would be a use case where you'd probably
 want to use the static keyword

0:03:25.400000 --> 0:03:30.700000
 here. Static is telling dynamic ARP
 inspection, hey, the only way you

0:03:30.700000 --> 0:03:35.000000
 can validate ARP requests and replies
 is with the ARP access list.

0:03:35.000000 --> 0:03:38.140000
 If you don't find a permit statement
 here, you're done.

0:03:38.140000 --> 0:03:40.020000
 There's nothing to fall back on.

0:03:40.020000 --> 0:03:44.440000
 So that's what the presence of the static
 keyword is in your IP ARP inspection

0:03:44.440000 --> 0:03:48.940000
 filter command. And this
 is a quick review.

0:03:48.940000 --> 0:03:53.340000
 Just wanted to point out that in dynamic
 ARP inspection, the normal things

0:03:53.340000 --> 0:04:00.320000
 that are checked are the sender's MAC
 address, the sender's IP address,

0:04:00.320000 --> 0:04:02.900000
 and the VLAN of the
 incoming interface.

0:04:02.900000 --> 0:04:06.780000
 That's what we check against the
 DHCP snooping binding database.

0:04:06.780000 --> 0:04:11.240000
 Alternatively, if you want to check
 more things, you could also have IP

0:04:11.240000 --> 0:04:15.500000
 ARP inspection validate the source
 MAC address of the actual Ethernet

0:04:15.500000 --> 0:04:23.120000
 header itself. Because keep in mind
 this, in a normal situation, if I'm

0:04:23.120000 --> 0:04:30.360000
 sending an ARP request, or if I'm sending
 an ARP reply, either one, if

0:04:30.360000 --> 0:04:34.640000
 that frame is being sourced from my
 laptop, well, my MAC address will

0:04:34.640000 --> 0:04:39.260000
 be right here, and my MAC address
 should also be right here.

0:04:39.260000 --> 0:04:44.000000
 If these MAC addresses are different,
 that's usually an indication of

0:04:44.000000 --> 0:04:45.780000
 someone who's trying
 to spoof something.

0:04:45.780000 --> 0:04:53.320000
 Someone who's trying to do something
 kind of a little bit threatening.

0:04:53.320000 --> 0:04:57.800000
 So this might be a good reason why you
 might want to check both MAC addresses

0:04:57.800000 --> 0:04:59.980000
 to make sure that
 they're the same.

0:04:59.980000 --> 0:05:01.320000
 And that's where you could
 do this right here.

0:05:01.320000 --> 0:05:06.580000
 You could also check destination MAC,
 and you could also check IP, which

0:05:06.580000 --> 0:05:08.540000
 would be the target IP address.

0:05:08.540000 --> 0:05:16.500000
 That is also checkable.

0:05:16.500000 --> 0:05:20.560000
 Another thing that dynamic ARP inspection
 can do is rate limiting.

0:05:20.560000 --> 0:05:24.540000
 A very common form of a network attack
 is an ARP attack where someone

0:05:24.540000 --> 0:05:30.640000
 will say, hey, I know that if I send
 an ARP request to your device, it's

0:05:30.640000 --> 0:05:32.340000
 going to interrupt your CPU.

0:05:32.340000 --> 0:05:36.460000
 Whether your device is a router or
 a server or even a PC, when you get

0:05:36.460000 --> 0:05:39.940000
 an ARP request, your CPU has to stop what
 it's doing for a few milliseconds

0:05:39.940000 --> 0:05:42.440000
 to process that ARP request.

0:05:42.440000 --> 0:05:47.000000
 So what better way to kill your device
 than for me to just send thousands

0:05:47.000000 --> 0:05:50.640000
 of ARP requests every
 second to your device?

0:05:50.640000 --> 0:05:54.720000
 Your CPU will be so overwhelmed trying
 to handle all that, it'll probably

0:05:54.720000 --> 0:05:58.780000
 crash and die. Well, with ARP
 inspection, we can limit that.

0:05:58.780000 --> 0:06:01.800000
 And you can see by default, it's limited
 to 15 packets per second, but

0:06:01.800000 --> 0:06:05.900000
 you can raise or lower that with this
 interface command right here.

0:06:05.900000 --> 0:06:09.900000
 And notice that's only really applied
 on untrusted interfaces.

0:06:09.900000 --> 0:06:13.720000
 It does not really affect
 trusted interfaces.

0:06:13.720000 --> 0:06:21.200000
 So this is our primary verification
 command show IP ARP inspection.

0:06:21.200000 --> 0:06:24.580000
 We can validate that in this particular
 case, it has been enabled on VLAN

0:06:24.580000 --> 0:06:26.580000
 18, it is active.

0:06:26.580000 --> 0:06:28.780000
 And at the moment, nothing's
 really happened.

0:06:28.780000 --> 0:06:32.620000
 We don't have any forwarded
 or dropped packets.

0:06:32.620000 --> 0:06:36.980000
 We can also do show IP ARP inspection and
 then specify a particular interface

0:06:36.980000 --> 0:06:39.780000
 to confirm the trust state
 of that interface.

0:06:39.780000 --> 0:06:41.780000
 Is it trusted or is it untrusted?

0:06:41.780000 --> 0:06:49.720000
 And what is the rate of packets per second
 that are allowed in this interface?

0:06:49.720000 --> 0:06:57.300000
 So that concludes this review
 of dynamic ARP inspection.

