WEBVTT

0:00:03.040000 --> 0:00:08.560000
 Welcome to this video on a review of
 InterVLAN routing for our CCNA 200

0:00:08.560000 --> 0:00:14.400000
-301 bootcamp. So InterVLAN routing
 is talking about a situation where

0:00:14.400000 --> 0:00:19.900000
 we have hosts in one VLAN needing to
 send their packets to hosts or A

0:00:19.900000 --> 0:00:22.240000
-host in a different VLAN.

0:00:22.240000 --> 0:00:25.620000
 Normally with this layer 2 switching
 that couldn't happen.

0:00:25.620000 --> 0:00:30.700000
 So we need something that can route the
 packets between those two subnets.

0:00:30.700000 --> 0:00:32.480000
 Now there are three
 ways to do that.

0:00:32.480000 --> 0:00:35.960000
 We could use a router on a stick model
 where the switch itself is just

0:00:35.960000 --> 0:00:37.380000
 a layer 2 switch.

0:00:37.380000 --> 0:00:40.820000
 The switch has no knowledge of routing
 and he's just forwarding his packets

0:00:40.820000 --> 0:00:42.980000
 to a router that's doing
 all that work.

0:00:42.980000 --> 0:00:47.580000
 We could actually enable the switch itself
 for routing with switched virtual

0:00:47.580000 --> 0:00:51.860000
 interfaces or we could convert some
 of the switching ports to layer 3

0:00:51.860000 --> 0:00:57.700000
 routed ports. If we do the router on
 a stick model the router will have

0:00:57.700000 --> 0:01:01.500000
 subinterfaces which is a single point
 of failure and probably not something

0:01:01.500000 --> 0:01:03.980000
 you want to do. So let's
 look right here.

0:01:03.980000 --> 0:01:07.500000
 So router on a stick
 simply means this.

0:01:07.500000 --> 0:01:12.060000
 I have my switch right here.

0:01:12.060000 --> 0:01:20.420000
 I have my router right here and I have
 a single interface connected to

0:01:20.420000 --> 0:01:27.080000
 that router. Now that single interface
 is configured as a VLAN trunk.

0:01:27.080000 --> 0:01:30.420000
 So on the switches side
 it's pretty easy.

0:01:30.420000 --> 0:01:45.480000
 All you have to do is switch port trunk
 encapsulation dot 1Q and then

0:01:45.480000 --> 0:01:52.320000
 we do switch port mode trunk.

0:01:52.320000 --> 0:01:53.640000
 That's all we have to do.

0:01:53.640000 --> 0:01:56.320000
 A little bit more work here on the
 router side which we'll talk about

0:01:56.320000 --> 0:02:00.240000
 in just a second but the whole point
 behind this is on the switches side.

0:02:00.240000 --> 0:02:02.120000
 We have a bunch of
 different VLANs.

0:02:02.120000 --> 0:02:05.000000
 This might here might be VLAN 2.

0:02:05.000000 --> 0:02:09.420000
 We might have some other hosts here
 in VLAN 3 and some other hosts here

0:02:09.420000 --> 0:02:13.780000
 in VLAN 4. And if the switch is not
 going to the routing force and the

0:02:13.780000 --> 0:02:18.180000
 router will we need all this traffic
 to be able to go up this trunk.

0:02:18.180000 --> 0:02:23.220000
 So it can be routed back and
 forth between by the switch.

0:02:23.220000 --> 0:02:25.720000
 I mean by the router,
 not the switch.

0:02:25.720000 --> 0:02:28.640000
 So in order to do this what we're going
 to do is we're going to go on

0:02:28.640000 --> 0:02:32.420000
 to this router's physical interface
 and we're going to break it up into

0:02:32.420000 --> 0:02:37.660000
 sub interfaces. So the physical interface
 might be fast ethernet 0 slash

0:02:37.660000 --> 0:02:41.900000
 0. All we have to do there
 is no shut and that's it.

0:02:41.900000 --> 0:02:46.780000
 And then we create these logical
 sub interfaces one per VLAN.

0:02:46.780000 --> 0:02:52.220000
 So we would say fast ethernet
 0 slash 0 dot.

0:02:52.220000 --> 0:02:55.020000
 And then we could put any number after
 the dot we want but typically we

0:02:55.020000 --> 0:02:56.880000
 put the number of the
 VLAN after the dot.

0:02:56.880000 --> 0:02:59.740000
 So why don't we start
 with 0 slash 0 dot 2.

0:02:59.740000 --> 0:03:08.780000
 Fast ethernet 0 slash 0 dot 3 and
 fast ethernet 0 slash 0 dot 4.

0:03:08.780000 --> 0:03:10.700000
 Then we have to tell
 each sub interface.

0:03:10.700000 --> 0:03:13.980000
 Hey, I need you to do 802
 dot 1 queue tagging.

0:03:13.980000 --> 0:03:18.580000
 So you can recognize incoming tags
 and you can apply outgoing tags.

0:03:18.580000 --> 0:03:23.120000
 So we use the encapsulation.

0:03:23.120000 --> 0:03:32.980000
 Dot 1 queue and then we put
 the VLAN number in there.

0:03:32.980000 --> 0:03:36.060000
 Capsulation dot 1 queue 3.

0:03:36.060000 --> 0:03:42.160000
 Capsulation dot 1 queue 4.

0:03:42.160000 --> 0:03:45.160000
 And then lastly, we put our
 IP addresses on here.

0:03:45.160000 --> 0:03:46.320000
 We put the IP address.

0:03:46.320000 --> 0:03:49.060000
 It's appropriate for VLAN 2.

0:03:49.060000 --> 0:03:52.120000
 Whatever subnet that
 is an IP address.

0:03:52.120000 --> 0:03:56.060000
 It's appropriate for VLAN
 3 and IP address.

0:03:56.060000 --> 0:03:57.800000
 It's appropriate for VLAN 4.

0:03:57.800000 --> 0:04:00.300000
 And that's what we see
 here on this slide.

0:04:00.300000 --> 0:04:06.420000
 Create our sub interfaces and then on each
 sub interface we do the encapsulation

0:04:06.420000 --> 0:04:09.100000
 dot 1 queue command
 and an IP address.

0:04:09.100000 --> 0:04:11.840000
 And then the router will be able to
 route between those sub interfaces

0:04:11.840000 --> 0:04:14.980000
 because they have created
 connected routes.

0:04:14.980000 --> 0:04:18.020000
 And a router can route back and forth
 between connected routes all day

0:04:18.020000 --> 0:04:21.420000
 long. We don't need any routing
 protocol or anything to do that.

0:04:21.420000 --> 0:04:24.520000
 Now, like I said in the previous slide,
 the downside to this is that router

0:04:24.520000 --> 0:04:26.080000
 is a single point of failure.

0:04:26.080000 --> 0:04:30.760000
 If it fails, those hosts will not
 have any default gateway anymore.

0:04:30.760000 --> 0:04:32.940000
 Or maybe the router itself
 might not fail.

0:04:32.940000 --> 0:04:36.960000
 Maybe somebody yanks out that cable, that
 trunking cable between the router

0:04:36.960000 --> 0:04:40.620000
 and the switch. So for that reason,
 it might be better just to have the

0:04:40.620000 --> 0:04:43.360000
 switch itself do the
 routing for us.

0:04:43.360000 --> 0:04:46.740000
 And in most modern network designs
 today, that's what you'll actually

0:04:46.740000 --> 0:04:50.640000
 see. That the switch itself, the access
 layer switch is actually doing

0:04:50.640000 --> 0:04:53.640000
 the routing and serving
 as the default gateway.

0:04:53.640000 --> 0:04:56.580000
 So you can do that
 in one of two ways.

0:04:56.580000 --> 0:05:02.560000
 So we could use SBIs.

0:05:02.560000 --> 0:05:06.560000
 So we could just simply say, okay, well,
 I've got VLAN 2, so I'll create

0:05:06.560000 --> 0:05:11.460000
 an interface. Well, actually just
 take a look at the next slide.

0:05:11.460000 --> 0:05:16.800000
 Right here, I'll create
 an interface VLAN 2.

0:05:16.800000 --> 0:05:19.440000
 And then I'll put an IP address on
 it that's in the same subnet as all

0:05:19.440000 --> 0:05:21.120000
 my hosts in VLAN 2.

0:05:21.120000 --> 0:05:24.920000
 And then I've got some hosts here in
 VLAN 3, so I'll create an interface

0:05:24.920000 --> 0:05:28.260000
 VLAN 3, put an IP
 address on there.

0:05:28.260000 --> 0:05:34.260000
 Now, the switches, most switches don't
 have routing enabled by default.

0:05:34.260000 --> 0:05:37.580000
 So you can create switch virtual interfaces,
 that's what we call these

0:05:37.580000 --> 0:05:39.300000
 interface VLANs right here.

0:05:39.300000 --> 0:05:42.580000
 You can create these all day long, but
 they won't be able to route packets

0:05:42.580000 --> 0:05:44.700000
 back and forth between them.

0:05:44.700000 --> 0:05:49.740000
 That's why on most switches, we also
 have to enable IP routing globally

0:05:49.740000 --> 0:05:51.580000
 to enable it to do that.

0:05:51.580000 --> 0:05:54.600000
 That turns on routing
 functionality.

0:05:54.600000 --> 0:05:58.100000
 And then, of course, we'd have to
 get our DHCP server involved.

0:05:58.100000 --> 0:06:02.580000
 Our DHCP server would have to know
 that when a DHCP discover comes in

0:06:02.580000 --> 0:06:06.400000
 from somebody in VLAN 2, the DHCP server
 should say, oh, your default

0:06:06.400000 --> 0:06:08.680000
 gateway is 2.2.2.2.

0:06:08.680000 --> 0:06:15.340000
 And for you guys over there in VLAN
 3, your default gateway is 3.3.3.3.

0:06:15.340000 --> 0:06:19.360000
 Or, of course, we could make it even
 easier and configure this exact same

0:06:19.360000 --> 0:06:22.400000
 switch as our DHCP server.

0:06:22.400000 --> 0:06:30.540000
 One other alternative you could do is
 we could have layer 3 routed ports.

0:06:30.540000 --> 0:06:36.360000
 So an example of this is done on
 the distribution layer switches.

0:06:36.360000 --> 0:06:38.380000
 Let me give you an
 example of that.

0:06:38.380000 --> 0:06:42.340000
 Let's say we have a
 switch right here.

0:06:42.340000 --> 0:06:49.440000
 Switch 1. And he's got
 something like this.

0:06:49.440000 --> 0:06:55.320000
 So this is going to be VLAN 1.

0:06:55.320000 --> 0:06:59.860000
 Actually, let's make it
 even simpler like this.

0:06:59.860000 --> 0:07:05.600000
 Let's say we've got three
 access layer switches.

0:07:05.600000 --> 0:07:10.300000
 Switch 1, switch 2, and switch 3.

0:07:10.300000 --> 0:07:13.860000
 Each access layer switch is
 only serving a single VLAN.

0:07:13.860000 --> 0:07:17.540000
 So maybe this guy here
 is serving VLAN 1.

0:07:17.540000 --> 0:07:20.400000
 This access layer switch.

0:07:20.400000 --> 0:07:23.840000
 He's only doing VLAN 2.

0:07:23.840000 --> 0:07:25.160000
 And this other guy.

0:07:25.160000 --> 0:07:28.340000
 He's doing VLAN 3.

0:07:28.340000 --> 0:07:34.820000
 Okay. And they're all connected
 up to a distribution switch.

0:07:34.820000 --> 0:07:39.060000
 Who's going to do the routing back
 and forth between these VLANs?

0:07:39.060000 --> 0:07:43.240000
 Well, we could on this distribution
 switch, we could say, hey, I'm going

0:07:43.240000 --> 0:07:45.980000
 to make this an access
 port in VLAN 1.

0:07:45.980000 --> 0:07:49.320000
 And then in that switch, I'm going
 to create interface VLAN 1 and put

0:07:49.320000 --> 0:07:51.960000
 an IP address on it like we
 just saw in the last slide.

0:07:51.960000 --> 0:07:54.880000
 And then we can say, hey, I'm going
 to make this an access port in VLAN

0:07:54.880000 --> 0:07:57.360000
 2 and create a switch virtual
 interface for that.

0:07:57.360000 --> 0:07:58.800000
 You could do that.

0:07:58.800000 --> 0:08:02.280000
 Or we could just say, hey, I'm going
 to go this interface right here and

0:08:02.280000 --> 0:08:04.020000
 do these two commands.

0:08:04.020000 --> 0:08:08.020000
 No switch port. And now that it's now
 I've just converted into what's

0:08:08.020000 --> 0:08:10.040000
 called a routed interface.

0:08:10.040000 --> 0:08:12.820000
 And now I can actually put
 an IP address on it.

0:08:12.820000 --> 0:08:14.660000
 And that IP address.

0:08:14.660000 --> 0:08:20.940000
 So 1.1.1.99. That can serve as the
 default gateway for all the people

0:08:20.940000 --> 0:08:24.080000
 in VLAN 1. And I could do
 the same thing over here.

0:08:24.080000 --> 0:08:30.180000
 I could say no switch port on that and
 give him an IP address that will

0:08:30.180000 --> 0:08:34.960000
 be serving as the default gateway
 for all the people in that VLAN.

0:08:34.960000 --> 0:08:38.180000
 So that's what we mean
 by routed interfaces.

0:08:38.180000 --> 0:08:42.060000
 Interfaces where we disabled
 their switch port capability.

0:08:42.060000 --> 0:08:43.700000
 They're no longer in a VLAN.

0:08:43.700000 --> 0:08:46.760000
 And they're just like an interface
 and a router where you can stick an

0:08:46.760000 --> 0:08:51.620000
 IP address on. Now remember, even if
 we do that on the switch, we're still

0:08:51.620000 --> 0:08:56.980000
 globally going to want to type IP routing
 to enable to route between our

0:08:56.980000 --> 0:09:03.180000
 connected interfaces.

0:09:03.180000 --> 0:09:04.780000
 Here's an example of that.

0:09:04.780000 --> 0:09:07.600000
 Just like it drew on the whiteboard
 just a moment ago.

0:09:07.600000 --> 0:09:17.480000
 I don't think there's really anything
 to add to this picture.

0:09:17.480000 --> 0:09:20.380000
 And we can do show
 IP route connected.

0:09:20.380000 --> 0:09:26.380000
 To verify that routing is actually enabled,
 whether it be on our router

0:09:26.380000 --> 0:09:28.660000
 or on our switch.

0:09:28.660000 --> 0:09:34.720000
 So that concludes this video
 on inter VLAN routing.

0:09:34.720000 --> 0:09:35.460000
 I hope you found it helpful.

