WEBVTT

0:00:03.260000 --> 0:00:07.460000
 Hello and welcome to this video
 titled implementing IPv6.

0:00:07.460000 --> 0:00:11.620000
 So what we're talking about here is
 how do you configure and enable IPv6

0:00:11.620000 --> 0:00:14.040000
 on Cisco iOS devices?

0:00:14.040000 --> 0:00:20.020000
 All right, so first we probably want
 to enable IPv6 on an interface.

0:00:20.020000 --> 0:00:22.180000
 And so there's a couple
 of ways to do this.

0:00:22.180000 --> 0:00:27.160000
 If you want to give that interface a globally
 routable address, and remember

0:00:27.160000 --> 0:00:33.900000
 that's some one colon one one one one
 one colon two two two two so on

0:00:33.900000 --> 0:00:36.580000
 and so forth, well there's
 no way to do that.

0:00:36.580000 --> 0:00:43.420000
 It's to type the command IPv6 address,
 type in your full address, and

0:00:43.420000 --> 0:00:45.740000
 then you have a choice here.

0:00:45.740000 --> 0:00:48.580000
 And let me just go ahead
 and demonstrate this.

0:00:48.580000 --> 0:00:55.780000
 If you want to type in an IPv6 address
 and also include a static interface

0:00:55.780000 --> 0:01:00.560000
 ID, an interface ID that you are
 selecting yourself, for example.

0:01:00.560000 --> 0:01:04.280000
 Let's go here under this device.

0:01:04.280000 --> 0:01:13.280000
 Interface gigabit zero slash one, I could
 say IPv6 address 2001, I'm going

0:01:13.280000 --> 0:01:14.940000
 to give all eight words.

0:01:14.940000 --> 0:01:17.360000
 I'm not going to abbreviate anything
 just so you can see how it all plays

0:01:17.360000 --> 0:01:22.240000
 out. One one one one two two two
 two three three three three.

0:01:22.240000 --> 0:01:24.120000
 Okay, so I'm going to have
 that as my prefix.

0:01:24.120000 --> 0:01:26.940000
 The first 64 bits are going
 to be the prefix.

0:01:26.940000 --> 0:01:29.620000
 The last 64 bits, let's
 just make it real easy.

0:01:29.620000 --> 0:01:34.760000
 000, 000, remember I'm not abbreviating
 anything right now.

0:01:34.760000 --> 0:01:38.900000
 All right, so that's going
 to be my interface ID.

0:01:38.900000 --> 0:01:41.200000
 Then I would just follow
 it with colon colon.

0:01:41.200000 --> 0:01:45.760000
 Actually, I don't have to have
 colon colon just slash 64.

0:01:45.760000 --> 0:01:49.320000
 So that's telling the device
 I just configured it on.

0:01:49.320000 --> 0:01:58.080000
 Is telling it that slash 64 means
 this is my prefix right there.

0:01:58.080000 --> 0:02:02.900000
 And this in IPv4, we would
 call those the host bits.

0:02:02.900000 --> 0:02:05.400000
 In IPv6, we call that
 the interface ID.

0:02:05.400000 --> 0:02:10.660000
 So that's the way you do it when you
 want to give it a static prefix and

0:02:10.660000 --> 0:02:13.300000
 interface ID. And it takes it.

0:02:13.300000 --> 0:02:18.420000
 And here's another little gotcha or not
 a gotcha but a weirdness of IPv6.

0:02:18.420000 --> 0:02:23.660000
 In the world of IPv4, an interface,
 whether it be a NIC card on a laptop

0:02:23.660000 --> 0:02:29.080000
 or an interface on a router, only
 could have one IPv4 address.

0:02:29.080000 --> 0:02:35.920000
 Watch this, IP address
 n.0.0.1 255 000.

0:02:35.920000 --> 0:02:39.800000
 Right? Now, what happened when I tried
 to put another IPv4 address on

0:02:39.800000 --> 0:02:41.560000
 there? IP address.

0:02:41.560000 --> 0:02:48.220000
 First of all, before we do that,
 do show run interface gig 01.

0:02:48.220000 --> 0:02:51.180000
 All right. See how it's
 got one IPv4 address.

0:02:51.180000 --> 0:02:54.380000
 Now watch what happens when
 I put another one on there.

0:02:54.380000 --> 0:03:03.160000
 Okay. So do we have both
 10 001 and 20 001?

0:03:03.160000 --> 0:03:07.920000
 No we don't. Right?

0:03:07.920000 --> 0:03:12.660000
 Because it can only, it's only expecting
 one IPv4 network to be on that

0:03:12.660000 --> 0:03:16.200000
 interface. So it overrope
 the older one.

0:03:16.200000 --> 0:03:20.780000
 What happens when I do the
 same thing for IPv6?

0:03:20.780000 --> 0:03:38.160000
 Now let's just change my prefix
 to be something else.

0:03:38.160000 --> 0:03:43.340000
 Okay. So did that override
 my previous address?

0:03:43.340000 --> 0:03:47.840000
 No, it didn't. So in IPv6 and you'll
 just have to sort of noodle this

0:03:47.840000 --> 0:03:50.840000
 around yourself as to why
 you would want this.

0:03:50.840000 --> 0:03:54.900000
 A NIC card, whether it be a NIC card
 on a laptop, smartphone or a router,

0:03:54.900000 --> 0:03:58.460000
 can have multiple IPv6 networks
 assigned to it.

0:03:58.460000 --> 0:04:00.000000
 Not sure why you'd
 want to do that.

0:04:00.000000 --> 0:04:03.980000
 I'm sure there's some valid use cases,
 but that is a different behavior

0:04:03.980000 --> 0:04:10.820000
 than IPv4. So in IPv4, if I want to
 take out my address, all I had to

0:04:10.820000 --> 0:04:15.080000
 say was no IP address and
 it took the command.

0:04:15.080000 --> 0:04:18.940000
 Now that IPv4 address I
 had on there is gone.

0:04:18.940000 --> 0:04:21.460000
 You can't do that with IPv6.

0:04:21.460000 --> 0:04:24.760000
 Okay. Well, let's see.

0:04:24.760000 --> 0:04:26.940000
 What happened? What happened
 when I did that?

0:04:26.940000 --> 0:04:27.900000
 Might surprise me.

0:04:27.900000 --> 0:04:30.320000
 Oh, wow. That's the first
 time I've seen that.

0:04:30.320000 --> 0:04:31.460000
 How nice is that?

0:04:31.460000 --> 0:04:36.560000
 So in older versions of iOS, you actually
 would get an error message because

0:04:36.560000 --> 0:04:40.120000
 the older iOS would say, hey, I've
 got multiple prefixes on here.

0:04:40.120000 --> 0:04:42.120000
 Which one do you want
 me to get rid of?

0:04:42.120000 --> 0:04:46.240000
 And so you'd actually have to type no
 IPv6 address in the whole address.

0:04:46.240000 --> 0:04:51.220000
 It was really irritating if your goal
 was to strip out all the IPv6.

0:04:51.220000 --> 0:04:54.700000
 It looks like in the newer code now,
 which is nice, you can actually type

0:04:54.700000 --> 0:04:58.640000
 no IPv6 address and it gets rid of all
 the prefixes on there, which could

0:04:58.640000 --> 0:05:01.980000
 be a little bit dangerous, I suppose,
 if you just intended on getting

0:05:01.980000 --> 0:05:03.860000
 rid of just one of them.

0:05:03.860000 --> 0:05:05.060000
 So be aware of that.

0:05:05.060000 --> 0:05:08.380000
 Now as far as configuration is concerned,
 so far I've shown you configuration

0:05:08.380000 --> 0:05:13.880000
 of IPv6 addresses where the prefix
 and the interface ID, I assigned it

0:05:13.880000 --> 0:05:20.900000
 myself. Alternatively, you could say IPv6
 address, just give it the prefix.

0:05:20.900000 --> 0:05:25.960000
 And then you could
 say colon colon.

0:05:25.960000 --> 0:05:30.840000
 So that's saying I'm not going to
 give you the rest of it slash 64.

0:05:30.840000 --> 0:05:35.420000
 Now if I just hit enter right now,
 it's going to say, hey, you haven't

0:05:35.420000 --> 0:05:38.000000
 given me the interface ID, you're
 giving me the prefix.

0:05:38.000000 --> 0:05:40.500000
 But what am I supposed to
 do for my interface ID?

0:05:40.500000 --> 0:05:47.380000
 So if I'm going to do that, now I can
 say EUI 64, which says, hey, do

0:05:47.380000 --> 0:05:50.980000
 you drive the interface
 ID yourself dynamically?

0:05:50.980000 --> 0:05:54.820000
 Now you won't see that interface
 ID as a result of show run.

0:05:54.820000 --> 0:06:02.020000
 You'll just see exactly what
 you typed in, right?

0:06:02.020000 --> 0:06:11.720000
 EUI 64. But if you do show IPv6 interface
 brief, now you will see not

0:06:11.720000 --> 0:06:16.440000
 only the prefix, but the interface
 ID that it dynamically derived via

0:06:16.440000 --> 0:06:18.880000
 the EUI 64 process.

0:06:18.880000 --> 0:06:24.340000
 If now routers are static, right?

0:06:24.340000 --> 0:06:25.580000
 Routers don't move around.

0:06:25.580000 --> 0:06:28.200000
 You know, once you assign them to
 a case, that's where they go.

0:06:28.200000 --> 0:06:30.240000
 Not like host, not like
 things that are mobile.

0:06:30.240000 --> 0:06:34.440000
 So things that are mobile are going
 to be using Slack, stateless address

0:06:34.440000 --> 0:06:38.400000
 automatic configuration to dynamically
 get their entire thing.

0:06:38.400000 --> 0:06:43.040000
 For the purposes of a lab, we could
 have a router's interface act like

0:06:43.040000 --> 0:06:48.400000
 a host and use Slack to get its IPv6
 address from another router that

0:06:48.400000 --> 0:06:50.920000
 is directly connected
 to on the other side.

0:06:50.920000 --> 0:06:55.940000
 The way we would do that is this.

0:06:55.940000 --> 0:07:04.440000
 We would just say IPv6
 address auto config.

0:07:04.440000 --> 0:07:09.320000
 And that tells it use stateless address
 automatic configuration to obtain

0:07:09.320000 --> 0:07:15.580000
 your address. Notice we could also
 do IPv6 address DHCP, which like a

0:07:15.580000 --> 0:07:20.540000
 host would mean use DHCP
 V6 to get your address.

0:07:20.540000 --> 0:07:25.480000
 All sorts of permutations
 here that we can use.

0:07:25.480000 --> 0:07:28.960000
 Now, key thing here, this command.


0:07:28.960000 --> 0:07:34.020000
 If we're doing IPv6 on a router, it's
 probably because we want him to

0:07:34.020000 --> 0:07:38.960000
 be able to route IPv6 packets between
 different IPv6 prefixes.

0:07:38.960000 --> 0:07:43.660000
 Hey, we might even want to do something
 crazy like enable IPv6 EI-GRP

0:07:43.660000 --> 0:07:48.560000
 or IPv6 OSPF. Well, if we want our router
 to actually be able to do those

0:07:48.560000 --> 0:07:54.020000
 things, we have to enable
 IPv6 unitcast-routing.

0:07:54.020000 --> 0:07:57.760000
 So this is one of those commands that
 the moment you think, oh, I want

0:07:57.760000 --> 0:08:02.480000
 to configure IPv6 on my device, whether
 it be a router or a switch, first

0:08:02.480000 --> 0:08:06.040000
 thing you should do is
 IPv6 unitcast-routing.

0:08:06.040000 --> 0:08:07.840000
 That's why it's in red there.

0:08:07.840000 --> 0:08:13.540000
 If you don't type that in, he will not route
 even between connected interfaces.

0:08:13.540000 --> 0:08:17.780000
 And he certainly won't allow you to
 configure an IPv6 routing protocol.

0:08:17.780000 --> 0:08:20.300000
 Now, little gotcha there.

0:08:20.300000 --> 0:08:24.840000
 I've seen different behavior on
 different flavors of Cisco iOS.

0:08:24.840000 --> 0:08:29.660000
 I've seen some devices that if you forgot
 to configure IPv6 unitcast-routing

0:08:29.660000 --> 0:08:35.360000
 and you tried to configure IPv6 router
 EI-GRP or IPv6 router OSPF, you

0:08:35.360000 --> 0:08:36.420000
 would get an error message.

0:08:36.420000 --> 0:08:39.320000
 It would say IPv6 routing
 is not enabled.

0:08:39.320000 --> 0:08:41.060000
 That would make sense.

0:08:41.060000 --> 0:08:45.180000
 I've seen other flavors of iOS that
 would actually let you configure the

0:08:45.180000 --> 0:08:50.400000
 routing protocol, type in all your commands,
 not give you any error message.

0:08:50.400000 --> 0:08:55.320000
 But if IPv6 unitcast-routing wasn't
 configured, nothing happened.

0:08:55.320000 --> 0:08:56.760000
 The routing protocol
 didn't start up.

0:08:56.760000 --> 0:09:00.540000
 It didn't do anything, which seems
 a little bit sneaky to me.

0:09:00.540000 --> 0:09:02.320000
 It seems like they
 should warn you.

0:09:02.320000 --> 0:09:07.380000
 So just be aware, make sure to configure
 IPv6 unitcast-routing.

0:09:07.380000 --> 0:09:11.340000
 Because whether it takes your routing
 configuration or not, you won't

0:09:11.340000 --> 0:09:14.960000
 be able to do any routing
 without it.

0:09:14.960000 --> 0:09:20.040000
 IPv6 static routes, configuration is
 pretty much exactly the same as with

0:09:20.040000 --> 0:09:21.660000
 IPv4 static routes.

0:09:21.660000 --> 0:09:27.260000
 Just swap your v4 address and next
 top with a v6 address and next top.

0:09:27.260000 --> 0:09:34.120000
 IPv6 default route, pretty simple.


0:09:34.120000 --> 0:09:38.640000
 Same general concepts as what
 you learned with IPv4.

0:09:38.640000 --> 0:09:40.880000
 And here are your common
 verification commands.

0:09:40.880000 --> 0:09:45.260000
 Just think about if you already know
 how to verify something in the world

0:09:45.260000 --> 0:09:53.300000
 of IPv4 with a show IP something command,
 just think show IPv6 and that

0:09:53.300000 --> 0:09:57.220000
 same something. And
 you'll get the idea.

0:09:57.220000 --> 0:10:04.140000
 So that concludes this video on a refresher
 on IPv6 implementation in

