WEBVTT

0:00:03.180000 --> 0:00:06.800000
 Welcome to this video, which for the
 CCNA Bootcamp is a review of the

0:00:06.800000 --> 0:00:11.920000
 OSPF Designated Router and Backup Designated
 Router election process.

0:00:11.920000 --> 0:00:17.520000
 Now before we talk about what DRs and
 BDRs are and how they're elected,

0:00:17.520000 --> 0:00:21.620000
 we first have to do a review of another
 concept that's actually very important

0:00:21.620000 --> 0:00:25.660000
 and related to this, which
 is loopback interfaces.

0:00:25.660000 --> 0:00:32.180000
 So, as a review, interfaces on Cisco devices
 come in two different flavors,

0:00:32.180000 --> 0:00:35.680000
 physical interfaces that you can actually
 plug a cable into, stick your

0:00:35.680000 --> 0:00:39.380000
 finger in the hole right there, and
 logical interfaces, which have no

0:00:39.380000 --> 0:00:43.840000
 cable, it's just a placeholder in the
 mind of the CPU for adding an IP

0:00:43.840000 --> 0:00:46.160000
 address or doing something.

0:00:46.160000 --> 0:00:50.340000
 And some logical interfaces come as
 part of the router, for example, a

0:00:50.340000 --> 0:00:56.220000
 VTY line, a VTY line, which is used to
 terminate telnet and SSH sessions.

0:00:56.220000 --> 0:00:57.480000
 You don't have to create that.

0:00:57.480000 --> 0:01:00.480000
 The moment you boot up the router, it
 automatically creates these virtual

0:01:00.480000 --> 0:01:02.500000
 things called VTY lines.

0:01:02.500000 --> 0:01:06.260000
 Other virtual interfaces, you do have
 to create, like on your switch,

0:01:06.260000 --> 0:01:12.600000
 your interface VLAN 2 or interface VLAN
 3 or sub interfaces, or what we're

0:01:12.600000 --> 0:01:15.620000
 going to talk about, loopback interfaces,
 you have to manually create

0:01:15.620000 --> 0:01:19.700000
 them. So most logical interfaces have
 to be created via configuration

0:01:19.700000 --> 0:01:24.440000
 commands. Now, the good thing about a logical
 interface is it's not dependent

0:01:24.440000 --> 0:01:29.620000
 upon any keep-alives or any electrical
 heartbeats or any kind of line

0:01:29.620000 --> 0:01:32.980000
 protocol in order to
 maintain its status.

0:01:32.980000 --> 0:01:37.780000
 So, as long as the device is up, the
 CPU is up in the router or the switch

0:01:37.780000 --> 0:01:43.600000
 that the logical interface
 will also be up.

0:01:43.600000 --> 0:01:47.300000
 Now, when switches switched virtual
 interfaces, your interface VLANs,

0:01:47.300000 --> 0:01:52.280000
 those are a little bit in on your physical
 interfaces, but a loopback

0:01:52.280000 --> 0:01:55.020000
 interface that we're going
 to talk about here is not.

0:01:55.020000 --> 0:01:59.400000
 You could have a router or a switch where
 every single interface is disabled

0:01:59.400000 --> 0:02:03.300000
 and down. Nothing's physically plugged
 into that switch, but your loopback

0:02:03.300000 --> 0:02:06.200000
 interface could still
 be up and operational.

0:02:06.200000 --> 0:02:09.000000
 Now, why do we use a
 loopback interface?

0:02:09.000000 --> 0:02:10.360000
 Well, there's a lot of reasons.

0:02:10.360000 --> 0:02:13.800000
 So like it says here, we typically used
 to host the management IP address

0:02:13.800000 --> 0:02:18.320000
 for a device. So a lot of times people
 will say, oh, okay, I want this

0:02:18.320000 --> 0:02:20.060000
 router to be 111.

0:02:20.060000 --> 0:02:22.280000
 I want this router to be 112.

0:02:22.280000 --> 0:02:26.120000
 This one, 1113. So I want to apply an IP
 addressing scheme that's independent

0:02:26.120000 --> 0:02:30.480000
 of my actual networks are carrying
 data, and I want that to be used to

0:02:30.480000 --> 0:02:33.560000
 manage to like telnet
 or SSH to the device.

0:02:33.560000 --> 0:02:36.900000
 So a place in that IP address on a
 loopback interface is a great idea

0:02:36.900000 --> 0:02:40.060000
 for that. It's also great for lab environments
 to create extra networks

0:02:40.060000 --> 0:02:42.380000
 for learning routing protocols.

0:02:42.380000 --> 0:02:45.760000
 Let's say that we have a lab environment
 where I'm a router, you're a

0:02:45.760000 --> 0:02:47.240000
 router, and that's it.

0:02:47.240000 --> 0:02:49.380000
 It's just the two of
 us with a cable.

0:02:49.380000 --> 0:02:55.660000
 And I want to go on my router and I want
 my RIP or OSPF or BGP to advertise

0:02:55.660000 --> 0:02:58.220000
 like 15 different networks to you.


0:02:58.220000 --> 0:03:01.340000
 Well, how are we going to do that if
 there's just one cable between us?

0:03:01.340000 --> 0:03:05.700000
 We can use loopback interfaces because
 when you create a loopback interface

0:03:05.700000 --> 0:03:14.460000
 and you put an IP address on a physical
 interface, they had a cable.

0:03:14.460000 --> 0:03:18.560000
 So I can just create 15 or 20 loopbacks
 with different networks on them.

0:03:18.560000 --> 0:03:22.380000
 And now I've got some stuff I can advertise
 to you to play around with.

0:03:22.380000 --> 0:03:27.140000
 And some protocols such as OSPF use the
 IP address on your loopback interface

0:03:27.140000 --> 0:03:30.580000
 as part of their processing rules.


0:03:30.580000 --> 0:03:33.780000
 So how do we create a
 loopback interface?

0:03:33.780000 --> 0:03:36.500000
 Real simple. So here it is before.


0:03:36.500000 --> 0:03:44.920000
 All right. All we do is a global configuration
 level, just type interface,

0:03:44.920000 --> 0:03:46.980000
 loopback, and then a number.

0:03:46.980000 --> 0:03:50.280000
 Most people typically start at loopback
 zero, but you don't have to.

0:03:50.280000 --> 0:03:55.400000
 You could do loopback 200, but the
 number is completely irrelevant.

0:03:55.400000 --> 0:03:58.740000
 The line, notice the line protocol,
 even before I put an IP address on

0:03:58.740000 --> 0:04:02.520000
 there, instantly goes up because that
 loopback interface is not dependent

0:04:02.520000 --> 0:04:05.200000
 on anything to bring up
 as line protocol status.

0:04:05.200000 --> 0:04:11.040000
 Then I add an IP address of 1111 1111
 and now under show IP interface

0:04:11.040000 --> 0:04:14.480000
 brief at the bottom, we actually see
 that loopback interface showing up

0:04:14.480000 --> 0:04:18.880000
 there. And if I looked at the routing
 table, if I did a show IP route,

0:04:18.880000 --> 0:04:24.780000
 we would now see a connected route
 for the 1111 1111.0 network.

0:04:24.780000 --> 0:04:28.980000
 All right. So what does this
 have to do with OSPF?

0:04:28.980000 --> 0:04:33.080000
 Well, OSPF, when you first started
 up, one of the very first things it

0:04:33.080000 --> 0:04:35.920000
 does, it elects a router
 ID for itself.

0:04:35.920000 --> 0:04:38.300000
 Think of this as being like
 a descriptive name.

0:04:38.300000 --> 0:04:44.120000
 So whenever this router creates an LSA
 describing itself, it's going to

0:04:44.120000 --> 0:04:47.660000
 plug that router ID in there
 as the advertising router.

0:04:47.660000 --> 0:04:53.180000
 So all the routers out there will
 know about you as your router ID.

0:04:53.180000 --> 0:04:56.980000
 So the router ID is also
 important in another way.

0:04:56.980000 --> 0:05:01.100000
 Not only does it describe you to the
 rest of the area so they know who

0:05:01.100000 --> 0:05:05.360000
 you are, but there's some election processes
 that take place between routers.

0:05:05.360000 --> 0:05:08.240000
 So when I'm forming a neighbor relationship
 with somebody, that router

0:05:08.240000 --> 0:05:13.920000
 ID is critical into determining who's
 going to play certain types of OSPF

0:05:13.920000 --> 0:05:18.080000
 roles. So how does OSPF come
 up with a router ID?

0:05:18.080000 --> 0:05:21.500000
 Well, this is the process
 that it goes through.

0:05:21.500000 --> 0:05:24.300000
 Number one, you can configure it.

0:05:24.300000 --> 0:05:28.340000
 Under the OSPF process, there's a router
 ID command where you can type

0:05:28.340000 --> 0:05:29.420000
 in the router ID.

0:05:29.420000 --> 0:05:31.140000
 So that's the first preference.

0:05:31.140000 --> 0:05:35.120000
 OSPF will look to see if you've
 manually added a router ID.

0:05:35.120000 --> 0:05:40.560000
 If you have not, then OSPF will look to
 see if you have any loopback interfaces

0:05:40.560000 --> 0:05:42.280000
 like we were just talking about.

0:05:42.280000 --> 0:05:46.780000
 And it'll pick the highest, the numerically
 highest IP address from among

0:05:46.780000 --> 0:05:51.580000
 your loopbacks. Now, let's say you
 don't have any loopback interfaces,

0:05:51.580000 --> 0:05:54.440000
 then OSPF will look at your
 physical interfaces.

0:05:54.440000 --> 0:06:00.980000
 Any physical interface that is not administratively
 down will be a candidate.

0:06:00.980000 --> 0:06:04.900000
 And so if you have no loopbacks, you'll
 pick the highest IP address from

0:06:04.900000 --> 0:06:09.540000
 any of your physical interfaces or your
 sub interfaces as long as they're

0:06:09.540000 --> 0:06:14.820000
 not shut down. As I mentioned, you can
 configure the router ID using the

0:06:14.820000 --> 0:06:19.020000
 router-id command under
 the OSPF instance.

0:06:19.020000 --> 0:06:28.820000
 Okay, so in broadcast and non-broadcast
 multi-access networks.

0:06:28.820000 --> 0:06:31.880000
 Now, you're probably not going to see
 non-broadcast multi-access networks

0:06:31.880000 --> 0:06:36.800000
 very much. If you're still dealing with
 frame relay networks, which are

0:06:36.800000 --> 0:06:42.500000
 a type of a WAN network, those are
 considered non-broadcast by OSPF.

0:06:42.500000 --> 0:06:47.420000
 But more and more if time goes on, Ethernet
 and all the flavors of Ethernet

0:06:47.420000 --> 0:06:50.200000
 are becoming more and more
 ubiquitous among networks.

0:06:50.200000 --> 0:06:54.200000
 And that's becoming like the only network
 type that people use these days.

0:06:54.200000 --> 0:06:56.520000
 And Ethernet is considered
 a broadcast network type.

0:06:56.520000 --> 0:07:00.880000
 But either way, OSPF elects
 a DR and a BDR.

0:07:00.880000 --> 0:07:02.800000
 So what is the purpose of this?

0:07:02.800000 --> 0:07:03.700000
 How does this work?

0:07:03.700000 --> 0:07:05.240000
 Well, here's how it works.

0:07:05.240000 --> 0:07:09.140000
 So imagine your typical environment
 where you have an Ethernet switch

0:07:09.140000 --> 0:07:15.820000
 and you have several routers
 connected to Ethernet switch.

0:07:15.820000 --> 0:07:22.480000
 Let's say router one, router two,
 router three, and router four.

0:07:22.480000 --> 0:07:25.100000
 Now, let's assume that the links to
 those routers are all in the same

0:07:25.100000 --> 0:07:37.860000
 VLAN. So we'll say this guy is 1.1
.1.1, 1.1.1.2, 1.1.1.3, and 1.1.1.4.

0:07:37.860000 --> 0:07:42.720000
 That's the actual IP address on their
 actual interfaces themselves.

0:07:42.720000 --> 0:07:48.400000
 OK, now when you enable OSPF on an
 interface, one thing the OSPF does

0:07:48.400000 --> 0:07:52.000000
 is OSPF has a priority,
 an interface priority.

0:07:52.000000 --> 0:07:54.820000
 Now, by default, the
 priority is one.

0:07:54.820000 --> 0:07:56.420000
 So I'll just put that right here.

0:07:56.420000 --> 0:07:59.680000
 OSPF interface priority is
 the same on all these guys.

0:07:59.680000 --> 0:08:10.520000
 OK, so what's going to happen here is
 that as these routers boot up, one

0:08:10.520000 --> 0:08:13.320000
 of them is going to be elected
 as the designated router.

0:08:13.320000 --> 0:08:15.680000
 Now, why do we need
 a designated router?

0:08:15.680000 --> 0:08:22.440000
 Well, let's contrast this with
 EIGRP as a routing protocol.

0:08:22.440000 --> 0:08:26.560000
 Now, in the world of routing with EIGRP,
 if all these routers here were

0:08:26.560000 --> 0:08:30.540000
 running EIGRP, they would all form
 neighbors with each other.

0:08:30.540000 --> 0:08:33.660000
 So if I was on router one, for example,
 I would see that I had three neighbors,

0:08:33.660000 --> 0:08:36.020000
 router two, three, and four.

0:08:36.020000 --> 0:08:41.860000
 And in the world of EIGRP, if router
 one learned of some new network via

0:08:41.860000 --> 0:08:47.120000
 that way, he would send that update
 into the switch, which would get to

0:08:47.120000 --> 0:08:51.540000
 router two, router three,
 and router four.

0:08:51.540000 --> 0:08:54.500000
 And then each one of those routers
 would be responsible for sending an

0:08:54.500000 --> 0:08:58.600000
 acknowledgement back to router
 one, saying, yep, I got it.

0:08:58.600000 --> 0:09:01.760000
 If one of the routers did not send an
 acknowledgement, router one would

0:09:01.760000 --> 0:09:05.660000
 resend that update specifically to that
 EIGRP neighbor, saying, hey, never

0:09:05.660000 --> 0:09:07.180000
 got an acknowledgement from you.

0:09:07.180000 --> 0:09:09.060000
 Here's some new information.

0:09:09.060000 --> 0:09:13.680000
 The desires of OSPF took
 a different approach.

0:09:13.680000 --> 0:09:17.340000
 So the desires of OSPF said, hey,
 here's what we're going to do.

0:09:17.340000 --> 0:09:21.220000
 One router is going to be elected
 as the designated router.

0:09:21.220000 --> 0:09:24.600000
 Another router is going to be elected
 as the backup of the designated

0:09:24.600000 --> 0:09:29.720000
 router. Then all the routers in this
 environment are going to form a fully

0:09:29.720000 --> 0:09:34.120000
 synchronized neighbor relationship
 with the DR and the BDR.

0:09:34.120000 --> 0:09:35.600000
 Not amongst each other.

0:09:35.600000 --> 0:09:38.760000
 They'll see each other's hello packets,
 but they're not going to exchange

0:09:38.760000 --> 0:09:40.360000
 database descriptors.

0:09:40.360000 --> 0:09:42.920000
 They're not going to change link state
 requests and link state updates

0:09:42.920000 --> 0:09:43.900000
 with each other.

0:09:43.900000 --> 0:09:47.720000
 They're only going to do that
 with the DR and the BDR.

0:09:47.720000 --> 0:09:52.620000
 Now, in this environment, how do we
 determine who that's going to be?

0:09:52.620000 --> 0:09:57.100000
 Well, the default is whoever's got the
 highest OSPF priority, that's number

0:09:57.100000 --> 0:10:01.020000
 one. So if one of these guys had a priority
 other than one, if somebody

0:10:01.020000 --> 0:10:03.020000
 was higher than that,
 they would win.

0:10:03.020000 --> 0:10:05.540000
 They would take on the role
 of the designated router.

0:10:05.540000 --> 0:10:10.100000
 If their priorities are the same, then
 it falls back to that router ID

0:10:10.100000 --> 0:10:11.140000
 we were just talking about.

0:10:11.140000 --> 0:10:13.380000
 So it's not the IP address.

0:10:13.380000 --> 0:10:17.340000
 So if I put in some different numbers
 in here for router IDs, let's say

0:10:17.340000 --> 0:10:24.600000
 we've got seven, seven, three, three,
 let's say we've got one dot two

0:10:24.600000 --> 0:10:27.240000
 dot one dot seventy seven.

0:10:27.240000 --> 0:10:33.380000
 Let's say we have nine dot nine dot
 one dot one and two dot two dot two

0:10:33.380000 --> 0:10:37.840000
 dot two. So in this environment, because
 they all have the same interface

0:10:37.840000 --> 0:10:42.400000
 priority, our designated router
 would end up being router one.

0:10:42.400000 --> 0:10:44.520000
 He's got the highest router ID.

0:10:44.520000 --> 0:10:51.700000
 So he would be my designated router
 and router three would end up being

0:10:51.700000 --> 0:10:57.340000
 my backup designated router because
 he has the second highest router ID.

0:10:57.340000 --> 0:11:05.820000
 Now that we know that, what we're going
 to see is, let's start with router

0:11:05.820000 --> 0:11:10.420000
 two. Router two will form a fully synchronized
 neighbor relationship with

0:11:10.420000 --> 0:11:13.260000
 router one and with router three.

0:11:13.260000 --> 0:11:17.960000
 Same thing same thing is going
 to happen with router four.

0:11:17.960000 --> 0:11:21.100000
 He's going to form a fully synchronized
 neighbor relationship with router

0:11:21.100000 --> 0:11:22.960000
 one and router three.

0:11:22.960000 --> 0:11:27.040000
 Matter of fact, router one and router
 three will form fully synchronized

0:11:27.040000 --> 0:11:30.400000
 neighbor relationships
 with each other.

0:11:30.400000 --> 0:11:38.040000
 Now, as far as what's going on between
 router two and router four, they

0:11:38.040000 --> 0:11:42.700000
 will see each other's hellos, but that's
 as far as they're going to go.

0:11:42.700000 --> 0:11:45.460000
 They will not exchange data based
 descriptors with each other.

0:11:45.460000 --> 0:11:48.120000
 They will not exchange
 link state requests.

0:11:48.120000 --> 0:11:59.480000
 So, if I was in, for example, router
 four, and in router four, I did the

0:11:59.480000 --> 0:12:02.120000
 command show IP OSPF neighbor.

0:12:02.120000 --> 0:12:03.600000
 Let's just get rid of
 some of this here.

0:12:03.600000 --> 0:12:06.100000
 So, I've got a little
 bit of space.

0:12:06.100000 --> 0:12:13.440000
 So, router four, I would see this.


0:12:13.440000 --> 0:12:19.080000
 I would see router one which would display
 as the designated router and

0:12:19.080000 --> 0:12:22.760000
 I am in the full state fully
 synchronized with him.

0:12:22.760000 --> 0:12:26.500000
 All of his LSAs match
 all of my LSAs.

0:12:26.500000 --> 0:12:30.620000
 Router three would display as
 the backup designated router.

0:12:30.620000 --> 0:12:38.660000
 Also in the full state, router two
 would display as a DR other, which

0:12:38.660000 --> 0:12:42.840000
 means he is neither the BDR.

0:12:42.840000 --> 0:12:47.060000
 He could become that in the future
 if the DR, the BDR drops out of the

0:12:47.060000 --> 0:12:51.420000
 picture, router two could take their
 spot, but he is right now neither.

0:12:51.420000 --> 0:12:55.220000
 And I am in the two-way state with him,
 which means I'm just exchanging

0:12:55.220000 --> 0:12:55.980000
 hellos with him.

0:12:55.980000 --> 0:12:58.900000
 I have not become fully synchronized
 with that guy.

0:12:58.900000 --> 0:13:06.920000
 And so now if, let's just take
 router two here for a second.

0:13:06.920000 --> 0:13:13.160000
 Let's say that router two is on the
 back end a neighbor with router X.

0:13:13.160000 --> 0:13:16.740000
 Okay? And router X sends him some sort
 of a link state update about some

0:13:16.740000 --> 0:13:18.120000
 new information.

0:13:18.120000 --> 0:13:24.520000
 Router two is going to forward that
 link state update to the DR and the

0:13:24.520000 --> 0:13:29.660000
 BDR. And to make sure that only they
 get it, he's going to send that to

0:13:29.660000 --> 0:13:37.120000
 224.006. That's a special multicast
 address that only the DR and the BDR

0:13:37.120000 --> 0:13:39.360000
 are actually listening to.

0:13:39.360000 --> 0:13:43.540000
 So router four is not going to pay
 attention to that because he's not

0:13:43.540000 --> 0:13:44.660000
 one of those roles.

0:13:44.660000 --> 0:13:48.480000
 So router one and router three will
 get that link state update to 224

0:13:48.480000 --> 0:13:55.700000
.006. Now that they've gotten it as
 it is the DR's responsibility, you

0:13:55.700000 --> 0:13:58.320000
 know, the router three will
 basically say, thank you.

0:13:58.320000 --> 0:13:59.680000
 And then just go silent.

0:13:59.680000 --> 0:14:03.480000
 Router one who's the DR will say, okay,
 I have to make sure that everybody

0:14:03.480000 --> 0:14:08.240000
 else in this particular broadcast domain
 in this VLAN also knows about

0:14:08.240000 --> 0:14:13.960000
 this. So he'll turn around and reflect
 that update right back out to 224

0:14:13.960000 --> 0:14:18.820000
.005. Well, it'll get
 to router two.

0:14:18.820000 --> 0:14:20.740000
 Router two will say, I've
 already got this.

0:14:20.740000 --> 0:14:23.260000
 Ignore it. It'll get
 to router three.

0:14:23.260000 --> 0:14:24.960000
 Route three will say,
 I've already got this.

0:14:24.960000 --> 0:14:30.000000
 Ignore it. But now router four
 can hear it for the first time.

0:14:30.000000 --> 0:14:36.480000
 So that's the idea behind a DR and
 a BDR in a broadcast environment, i

0:14:36.480000 --> 0:14:42.280000
.e. Everybody synchronizes
 with the DR and the BDR.

0:14:42.280000 --> 0:14:45.260000
 And when they learn of new information,
 they send it to the DR and the

0:14:45.260000 --> 0:14:49.360000
 BDR. And that's the responsibility
 of the designated router to reflect

0:14:49.360000 --> 0:14:58.480000
 that back and make sure that everybody
 is synchronized with that information.

0:14:58.480000 --> 0:15:01.960000
 So that's what we discussed
 right there.

0:15:01.960000 --> 0:15:04.580000
 And I've already mentioned this.

0:15:04.580000 --> 0:15:10.620000
 That the router with the highest priority
 becomes the designated router.

0:15:10.620000 --> 0:15:15.740000
 And the way you can influence that is
 if I was under router, I said, hey,

0:15:15.740000 --> 0:15:18.740000
 I really do want this router to
 become the designated router.

0:15:18.740000 --> 0:15:22.880000
 Then you would go on to an interface
 like interface, get the data, and

0:15:22.880000 --> 0:15:24.220000
 then you would go on
 to an interface.

0:15:24.220000 --> 0:15:30.800000
 And the command would
 be ipospf priority.

0:15:30.800000 --> 0:15:35.460000
 As long as he gave it something higher
 than one, he'll beat all the other

0:15:35.460000 --> 0:15:37.500000
 routers that have the default.

0:15:37.500000 --> 0:15:43.020000
 Now one thing to be aware of.

0:15:43.020000 --> 0:15:45.720000
 Now let me just see if this is coming
 up in the next slide before I talk

0:15:45.720000 --> 0:15:54.900000
 about it. Okay, so we're not it's not
 in the slides there so one thing

0:15:54.900000 --> 0:15:57.060000
 to be aware of is that.

0:15:57.060000 --> 0:16:01.960000
 Once the designated router and the backup
 doesn't eat router is elected

0:16:01.960000 --> 0:16:04.340000
 but this is focused
 on the DR right now.

0:16:04.340000 --> 0:16:09.600000
 It's kind of sticky in other words what
 I mean by that is, let's say that.

0:16:09.600000 --> 0:16:13.320000
 Let's say that you and I were connected
 to a switch and it's just you

0:16:13.320000 --> 0:16:17.180000
 and I and so we decide that you'll be
 the designated router I'll be the

0:16:17.180000 --> 0:16:19.540000
 backup because you have a
 higher router ID than me.

0:16:19.540000 --> 0:16:23.740000
 Great now let's say that your router
 ID is one dot one dot one dot four

0:16:23.740000 --> 0:16:27.860000
 and I'm one one one one one that's
 why you won because you're one one

0:16:27.860000 --> 0:16:29.600000
 one four okay great.

0:16:29.600000 --> 0:16:32.360000
 Let's say that in a few minutes or
 a few hours all of a sudden another

0:16:32.360000 --> 0:16:37.760000
 router joins the same switch and his
 router ID is higher than yours.

0:16:37.760000 --> 0:16:39.880000
 He's like one one one five.

0:16:39.880000 --> 0:16:44.580000
 It's too late. Once you're elected as
 the DR anybody else that comes in

0:16:44.580000 --> 0:16:48.060000
 after that point in time whether they've
 got a higher priority or they

0:16:48.060000 --> 0:16:52.540000
 have a higher router ID they cannot
 take over that role from you.

0:16:52.540000 --> 0:16:55.760000
 That's why I said it's sticky that
 roles are like sticks to you.

0:16:55.760000 --> 0:17:00.240000
 Now clearly if your interface goes down
 or if you crash and die well then

0:17:00.240000 --> 0:17:05.060000
 that guy now has the opportunity to
 take over the role but the DR sticks

0:17:05.060000 --> 0:17:11.640000
 to whoever gets elected
 to that position.

0:17:11.640000 --> 0:17:16.240000
 All right so here are some show commands
 you can use to view who your

0:17:16.240000 --> 0:17:22.180000
 various neighbors are and what their
 what their state is show IP OSPF

0:17:22.180000 --> 0:17:26.660000
 database will show you your LSA's show
 IP route OSPF will display the

0:17:26.660000 --> 0:17:29.780000
 routing table but only the
 OSPF learned routes.

0:17:29.780000 --> 0:17:36.920000
 And these are a couple of useful debug
 you can use to troubleshoot OSPF.

0:17:36.920000 --> 0:17:41.720000
 So that concludes this particular video
 on OSPF designated routers backup

0:17:41.720000 --> 0:17:44.920000
 designated routers and
 how they are elected.

0:17:44.920000 --> 0:17:45.780000
 I hope you found it useful.

