WEBVTT

0:00:02.700000 --> 0:00:08.020000
 Hello, in this video I'd like to do
 a review of standard access lists.

0:00:08.020000 --> 0:00:14.940000
 So a standard access list is purely
 used to filter or match on traffic

0:00:14.940000 --> 0:00:18.620000
 based on the layer three header and
 specifically within the layer three

0:00:18.620000 --> 0:00:22.540000
 header, the only thing it can check
 is the source IP address.

0:00:22.540000 --> 0:00:26.200000
 Now this might sound extremely limiting
 at first, but there's some features

0:00:26.200000 --> 0:00:31.820000
 where the source IP address
 and nothing else.

0:00:31.820000 --> 0:00:36.840000
 For example, at the CCNA level, you
 don't get into this feature, but you

0:00:36.840000 --> 0:00:38.640000
 can Google it if you're
 interested.

0:00:38.640000 --> 0:00:42.340000
 There's a feature that you get into at
 the CCNP level called policy based

0:00:42.340000 --> 0:00:47.100000
 routing. You see in normal routing,
 when a packet comes in, we check the

0:00:47.100000 --> 0:00:49.860000
 destination IP address only.

0:00:49.860000 --> 0:00:52.700000
 And based on the destination IP address,
 we go into the routing table

0:00:52.700000 --> 0:00:56.440000
 and then we say, okay, if the match
 is in the routing table, we'll send

0:00:56.440000 --> 0:00:57.680000
 out where it needs to go.

0:00:57.680000 --> 0:01:02.660000
 Policy based routing actually gives you
 the ability to match on the source

0:01:02.660000 --> 0:01:05.400000
 IP address of where
 traffic came from.

0:01:05.400000 --> 0:01:09.020000
 And then force that packet to go one
 direction or another based on your

0:01:09.020000 --> 0:01:10.960000
 selection, based on the source.

0:01:10.960000 --> 0:01:16.280000
 So this would be a prime use case
 for a standard access list.

0:01:16.280000 --> 0:01:21.720000
 Now when you're configuring
 numbered access lists.

0:01:21.720000 --> 0:01:27.320000
 So a numbered access list, you start
 out at global configuration level

0:01:27.320000 --> 0:01:32.000000
 and you actually type
 access dash list.

0:01:32.000000 --> 0:01:35.340000
 And then you provide
 a number right here.

0:01:35.340000 --> 0:01:39.760000
 Depending on what number you select,
 there's certain ranges of numbers.

0:01:39.760000 --> 0:01:42.120000
 And that's what we're going to get into
 now that if you select a number

0:01:42.120000 --> 0:01:46.100000
 from this range, for example, if you
 select a number from one to ninety

0:01:46.100000 --> 0:01:52.300000
 nine, at that point before you even
 go any further, Cisco iOS knows it's

0:01:52.300000 --> 0:01:54.160000
 going to give you standard
 access list.

0:01:54.160000 --> 0:01:58.820000
 It's only going to give you the options
 that a standard access list would

0:01:58.820000 --> 0:02:02.620000
 do. You're not going to see the options
 of some of the other access lists.

0:02:02.620000 --> 0:02:09.060000
 Now be aware that standard access list
 numbered access list actually have

0:02:09.060000 --> 0:02:10.180000
 two different ranges.

0:02:10.180000 --> 0:02:12.720000
 This is the normal
 range right here.

0:02:12.720000 --> 0:02:15.960000
 There's also something called
 the expanded range.

0:02:15.960000 --> 0:02:22.340000
 Meaning, hey, if you were a huge Internet
 service provider, something,

0:02:22.340000 --> 0:02:26.420000
 and they're well known for having sometimes
 hundreds and hundreds of lines

0:02:26.420000 --> 0:02:28.980000
 of access list is
 crazy access list.

0:02:28.980000 --> 0:02:32.120000
 You might run out of them if all you
 had was one through ninety nine to

0:02:32.120000 --> 0:02:36.280000
 pick from. Well, luckily, you can go
 into the expanded range, which is

0:02:36.280000 --> 0:02:39.780000
 thirteen hundred through
 ninety ninety nine.

0:02:39.780000 --> 0:02:44.020000
 That gives you a lot more standard
 access list you can configure.

0:02:44.020000 --> 0:02:49.960000
 General rule of standard access list
 is they should be applied nearest

0:02:49.960000 --> 0:02:51.800000
 to the destination.

0:02:51.800000 --> 0:02:58.900000
 Why is that? Well, if I have a host
 right here, router one, router two,

0:02:58.900000 --> 0:03:02.560000
 router three, and then
 here's the destination.

0:03:02.560000 --> 0:03:06.220000
 And let's say these routers also have
 some links going off somewhere else.

0:03:06.220000 --> 0:03:09.780000
 Let's say my objective
 was I want this host.

0:03:09.780000 --> 0:03:13.540000
 Let's just call him host a to be able
 to get to wherever he pretty much

0:03:13.540000 --> 0:03:17.420000
 wants to go. I just don't want
 him going to that server.

0:03:17.420000 --> 0:03:19.240000
 Don't want him going
 to the server.

0:03:19.240000 --> 0:03:23.660000
 Well, if I created a standard access
 list, let's just say he is one dot

0:03:23.660000 --> 0:03:24.680000
 one dot one dot one.

0:03:24.680000 --> 0:03:35.980000
 So if I said access dash list
 one, deny that host deny him.

0:03:35.980000 --> 0:03:38.200000
 Now, remember there's
 that implicit deny.

0:03:38.200000 --> 0:03:41.500000
 So if I just did that one line, everything
 else is going to be denied

0:03:41.500000 --> 0:03:45.460000
 to. So I'm going to want to
 create another line of this.

0:03:45.460000 --> 0:03:54.220000
 Access dash list one
 permit anyone else.

0:03:54.220000 --> 0:03:59.500000
 Okay. Now, remember the access list itself,
 the permit or deny statement.

0:03:59.500000 --> 0:04:02.800000
 You don't know what that's doing unless
 you actually have some feature

0:04:02.800000 --> 0:04:05.480000
 that you can see that's
 using the access list.

0:04:05.480000 --> 0:04:08.200000
 So we're going to talk about that feature
 in just one moment, but I'm

0:04:08.200000 --> 0:04:11.680000
 going to take that feature and I'm
 going to apply it right here.

0:04:11.680000 --> 0:04:13.460000
 I'm actually going
 to break this rule.

0:04:13.460000 --> 0:04:16.480000
 This rule says it should be applied
 as close to the destination.

0:04:16.480000 --> 0:04:18.360000
 Well, what happens
 if I don't do that?

0:04:18.360000 --> 0:04:22.940000
 What if I say, Hey, for all traffic coming
 in this interface, let's inspect

0:04:22.940000 --> 0:04:24.840000
 it against his access list.

0:04:24.840000 --> 0:04:26.060000
 Well, here's the problem.

0:04:26.060000 --> 0:04:30.440000
 Yes, that PC is not going to be able
 to get to that server, but he's also

0:04:30.440000 --> 0:04:32.200000
 not going to be able
 to get anywhere else.

0:04:32.200000 --> 0:04:35.220000
 He's not going to be able to take any
 of these other links because he's

0:04:35.220000 --> 0:04:36.200000
 going to be dropped.

0:04:36.200000 --> 0:04:42.700000
 That's why it's actually better to apply
 that access list right here in

0:04:42.700000 --> 0:04:45.940000
 the outbound direction as close
 to that server as possible.

0:04:45.940000 --> 0:04:49.560000
 That way that guy can pretty much have
 free access to get wherever he

0:04:49.560000 --> 0:04:53.140000
 wants until he gets right here.

0:04:53.140000 --> 0:04:56.600000
 If he tries to go out that interface,
 now he's blocked.

0:04:56.600000 --> 0:05:00.000000
 So this was the destination he was
 trying to get to, and we applied it

0:05:00.000000 --> 0:05:03.700000
 on the interface as close to that
 destination as we possibly could.

0:05:03.700000 --> 0:05:08.360000
 That's a general rule of
 standard access lists.

0:05:08.360000 --> 0:05:12.920000
 There's no way to check the destination
 address or port numbers.

0:05:12.920000 --> 0:05:16.880000
 So once again, standard access list,
 that's all it's looking at.

0:05:16.880000 --> 0:05:23.380000
 So we looked at the configuration of it,
 access dash list, just as a review.

0:05:23.380000 --> 0:05:27.980000
 So there's there's three ways
 you can configure this.

0:05:27.980000 --> 0:05:32.040000
 Access dash list.

0:05:32.040000 --> 0:05:37.760000
 Pick a number between one and 99.

0:05:37.760000 --> 0:05:40.760000
 Then put it either permit.

0:05:40.760000 --> 0:05:42.740000
 Or deny statement.

0:05:42.740000 --> 0:05:47.160000
 Okay, now let's go down here.

0:05:47.160000 --> 0:05:49.520000
 Here's my three options.

0:05:49.520000 --> 0:05:52.240000
 One, two, three.

0:05:52.240000 --> 0:05:57.240000
 If I'm trying to permit or deny a specific
 network or a subnet, like maybe

0:05:57.240000 --> 0:05:59.200000
 the 10.75 network.

0:05:59.200000 --> 0:06:04.560000
 I could say permit
 or deny 10.75.00.

0:06:04.560000 --> 0:06:07.580000
 And now I need to apply
 a wildcard mask.

0:06:07.580000 --> 0:06:14.720000
 So that wildcard mask will say, hey,
 any packet has a source address.

0:06:14.720000 --> 0:06:16.980000
 Where the first two octets.

0:06:16.980000 --> 0:06:20.260000
 Match 10.75. That's a match.

0:06:20.260000 --> 0:06:23.460000
 Hey, feature, whatever you're, whatever
 is using this access list, you

0:06:23.460000 --> 0:06:26.280000
 can do what you need to do.

0:06:26.280000 --> 0:06:29.500000
 Now, let's see, I'm trying to
 match a specific host address.

0:06:29.500000 --> 0:06:35.660000
 I want to match all 32 bits in the
 IP address, like maybe 10.75.1.1.

0:06:35.660000 --> 0:06:39.100000
 Well, I could put a wildcard
 mask of this.

0:06:39.100000 --> 0:06:42.920000
 That'll work. That wildcard mask says,
 Hey, all 32 bits are important

0:06:42.920000 --> 0:06:45.880000
 to me. I could certainly do that.

0:06:45.880000 --> 0:06:52.080000
 Or. Alternatively.

0:06:52.080000 --> 0:06:56.020000
 I could say. Host.

0:06:56.020000 --> 0:07:04.060000
 10.75.1.1. So if you proceed an actual
 host address with the word host,

0:07:04.060000 --> 0:07:08.640000
 that's exactly the same thing as if
 you had 0, 0, 0, 0 as your wildcard

0:07:08.640000 --> 0:07:11.000000
 mask after the host address.

0:07:11.000000 --> 0:07:16.060000
 Now, the last thing, what if I want
 to match on any source address?

0:07:16.060000 --> 0:07:17.620000
 I don't care what it is.

0:07:17.620000 --> 0:07:19.240000
 Well, I could do this.

0:07:19.240000 --> 0:07:21.920000
 I could just put some
 fake address in here.

0:07:21.920000 --> 0:07:24.780000
 And I could do this.

0:07:24.780000 --> 0:07:32.100000
 Right, because with that wildcard mask,
 that's saying, I don't have to

0:07:32.100000 --> 0:07:33.700000
 match any of these things.

0:07:33.700000 --> 0:07:34.720000
 So I could put anything in there.

0:07:34.720000 --> 0:07:39.620000
 And if I have that means match anything
 or what people usually do.

0:07:39.620000 --> 0:07:41.900000
 Is they actually just
 use the keyword.

0:07:41.900000 --> 0:07:50.560000
 Of any. Access list
 one permit any.

0:07:50.560000 --> 0:07:55.220000
 So those are the three ways you can
 configure a standard access list.

0:07:55.220000 --> 0:08:01.720000
 And you can use the show
 IP access dash list.

0:08:01.720000 --> 0:08:06.760000
 Or show run include access list to
 verify the presence of access list

0:08:06.760000 --> 0:08:08.520000
 in your configuration.

0:08:08.520000 --> 0:08:14.040000
 Now. Let's say that.

0:08:14.040000 --> 0:08:20.360000
 What my objective is is I want
 to block or permit packets.

0:08:20.360000 --> 0:08:22.280000
 Based on my access list.

0:08:22.280000 --> 0:08:25.680000
 Okay, so maybe I've got one access
 list over here that I'm using for,

0:08:25.680000 --> 0:08:27.540000
 you know, what should I encrypt?

0:08:27.540000 --> 0:08:29.000000
 What should I not encrypt?

0:08:29.000000 --> 0:08:32.580000
 I got another access list over here
 for what package should be applied

0:08:32.580000 --> 0:08:42.040000
 to that. And which one
 should be not natted.

0:08:42.040000 --> 0:08:45.840000
 Well, you create your access
 list exactly the same way.

0:08:45.840000 --> 0:08:48.480000
 It's just the feature that's going
 to use that access list.

0:08:48.480000 --> 0:08:53.480000
 Is the IP access dash
 group command.

0:08:53.480000 --> 0:08:57.480000
 So your access list
 is already done.

0:08:57.480000 --> 0:08:59.760000
 So let's say we've done that.

0:08:59.760000 --> 0:09:02.680000
 Access dash list.

0:09:02.680000 --> 0:09:11.240000
 One. Permit. Twenty dot twenty dot
 twenty dot zero zero zero zero zero

0:09:11.240000 --> 0:09:13.200000
 zero zero zero two fifty five.

0:09:13.200000 --> 0:09:18.720000
 Okay. Now if I go to my gigabit zero
 slash one interface and I say IP

0:09:18.720000 --> 0:09:22.120000
 access dash group one.

0:09:22.120000 --> 0:09:25.100000
 Which here is referencing
 that one.

0:09:25.100000 --> 0:09:27.200000
 And if I say in.

0:09:27.200000 --> 0:09:31.340000
 That means if any packet is received
 from the cable if any packets coming

0:09:31.340000 --> 0:09:33.320000
 inbound this interface.

0:09:33.320000 --> 0:09:38.520000
 If that packet. If the first three
 octets match twenty twenty twenty I

0:09:38.520000 --> 0:09:41.000000
 am permitted to forward
 that packet.

0:09:41.000000 --> 0:09:43.040000
 I will receive it.

0:09:43.040000 --> 0:09:47.020000
 If the packet has anything that's not
 twenty twenty twenty it will match

0:09:47.020000 --> 0:09:52.580000
 my implicit my invisible deny
 all and it will be filtered.

0:09:52.580000 --> 0:09:56.280000
 Or I could apply in the outbound pack
 outbound direction for packets I'm

0:09:56.280000 --> 0:10:03.100000
 about to transmit out
 onto the cable.

0:10:03.100000 --> 0:10:08.040000
 And if you want to see if the access group
 command has been applied anywhere.

0:10:08.040000 --> 0:10:11.140000
 You can do the show IP
 interface command.

0:10:11.140000 --> 0:10:13.680000
 And they'll tell you there's a lot
 of output in that command but it'll

0:10:13.680000 --> 0:10:16.540000
 tell you. Well let's just take a look
 at that so you can see what it looks

0:10:16.540000 --> 0:10:28.100000
 like. So let's just create a
 standard access list here.

0:10:28.100000 --> 0:10:35.740000
 Okay now let's go to an interface.


0:10:35.740000 --> 0:10:43.620000
 IP access dash group one in.

0:10:43.620000 --> 0:10:49.900000
 Okay so now if we do show
 IP interface gig zero one.

0:10:49.900000 --> 0:10:56.140000
 Notice right here it says inbound
 access list is one.

0:10:56.140000 --> 0:10:59.320000
 If I'd applied it in the
 outbound direction.

0:10:59.320000 --> 0:11:02.980000
 We would have seen something
 right here.

0:11:02.980000 --> 0:11:07.380000
 So that concludes this video on the monitoring
 and configuration of standard

