WEBVTT

0:00:03.120000 --> 0:00:07.280000
 Hello and welcome to this video in
 which is the final video right now

0:00:07.280000 --> 0:00:10.680000
 in our wireless series where I'm going
 to show you how to configure a

0:00:10.680000 --> 0:00:17.280000
 wireless LAN using WPA2 security credentials
 with pre-shared key on a

0:00:17.280000 --> 0:00:18.900000
 wireless controller.

0:00:18.900000 --> 0:00:24.540000
 Well, let's just do a quick summary
 here of WPA and WPA2.

0:00:24.540000 --> 0:00:30.520000
 So remember WPA was a certification program
 put out by the Wi-Fi Alliance,

0:00:30.520000 --> 0:00:35.400000
 an independent entity that certified
 Wi-Fi vendors equipment.

0:00:35.400000 --> 0:00:39.140000
 The WPA certification certified at
 their equipment could do the stuff

0:00:39.140000 --> 0:00:44.760000
 that was in a draft version
 of the 802.11i standard.

0:00:44.760000 --> 0:00:46.820000
 What about WPA2?

0:00:46.820000 --> 0:00:53.760000
 Well, when 802.11i was fully ratified,
 then all the things that were in

0:00:53.760000 --> 0:00:59.180000
 that standard could be certified against
 and given the WPA2 stamp of approval.

0:00:59.180000 --> 0:01:03.760000
 So if you created an access point and
 you gave it to the Wi-Fi Alliance,

0:01:03.760000 --> 0:01:07.640000
 you said, hey, this access point can
 do all the things that are in the

0:01:07.640000 --> 0:01:10.960000
 now fully ratified
 802.11i standard.

0:01:10.960000 --> 0:01:14.160000
 They would test your access point and
 if that was true, that it did all

0:01:14.160000 --> 0:01:19.460000
 the things in that document, you would
 get the WPA2 seal of approval.

0:01:19.460000 --> 0:01:24.020000
 Also one of the things that made WPA2
 better than WPA was they added a

0:01:24.020000 --> 0:01:27.040000
 much stronger form of
 encryption to that.

0:01:27.040000 --> 0:01:33.440000
 So WPA still relied on the RC4 encryption
 cipher with some tweaks to it.

0:01:33.440000 --> 0:01:40.980000
 WPA2 now added AESCCMP, which was actually
 even authorized by the National

0:01:40.980000 --> 0:01:45.960000
 Security Agency of the United States
 as being an authorized, legitimate

0:01:45.960000 --> 0:01:48.820000
 security standard for encryption.

0:01:48.820000 --> 0:01:53.020000
 So you really need to be using these
 days AESCCMP for your encryption,

0:01:53.020000 --> 0:01:54.920000
 if not something higher.

0:01:54.920000 --> 0:02:00.920000
 Now both methods offered personal
 and enterprise additions.

0:02:00.920000 --> 0:02:04.660000
 Personal was typically meant for a
 small office home office where the

0:02:04.660000 --> 0:02:13.680000
 encryption and nothing
 else was involved.

0:02:13.680000 --> 0:02:17.260000
 Enterprise additions were for larger
 scale environments where you would

0:02:17.260000 --> 0:02:21.460000
 need use of 802.1x, which requires
 a little bit more configuration, a

0:02:21.460000 --> 0:02:25.580000
 little bit more complexity on the client's
 side to get that working as

0:02:25.580000 --> 0:02:30.760000
 well as a radius server on the back end
 to do all the 802.1x authentication.

0:02:30.760000 --> 0:02:36.260000
 Even to this day, many companies, even
 larger companies, use the personal

0:02:36.260000 --> 0:02:42.880000
 additions of WPA2 simply because it's easier
 to implement, easier to configure,

0:02:42.880000 --> 0:02:46.360000
 no need for an 802.1x server.

0:02:46.360000 --> 0:02:52.100000
 All right, so let's walk through how you
 would configure a brand new wireless

0:02:52.100000 --> 0:03:00.420000
 LAN on a controller with WPA2 and pre shared
 key authentication and encryption.

0:03:00.420000 --> 0:03:04.920000
 Now, first of all, disclaimer, there
 are lots of different wireless LANs

0:03:04.920000 --> 0:03:08.640000
 out there. What I'm going to show you
 is one of Cisco's latest and greatest

0:03:08.640000 --> 0:03:13.760000
 wireless LAN controllers, which
 is their 9800 series controller.

0:03:13.760000 --> 0:03:17.740000
 And we're going to be working on
 the GUI of that controller type.

0:03:17.740000 --> 0:03:21.600000
 So that controller has already been
 pre configured with an IP address

0:03:21.600000 --> 0:03:23.620000
 so I can at least browse to it.

0:03:23.620000 --> 0:03:30.640000
 So if you remember, the way that a
 lot of these controllers worked was

0:03:30.640000 --> 0:03:37.420000
 that you had the controller and then
 you had a console port, which was

0:03:37.420000 --> 0:03:40.620000
 just used to get into the command line,
 but we're not going to do that.

0:03:40.620000 --> 0:03:42.760000
 The CCDA wants you to know
 how to do it on the GUI.

0:03:42.760000 --> 0:03:47.260000
 You also had a service port.

0:03:47.260000 --> 0:03:54.040000
 And with the service port, you could
 stick an IP address on it.

0:03:54.040000 --> 0:03:58.320000
 And now you could browse to that, browse
 to the GUI via that IP address.

0:03:58.320000 --> 0:04:00.880000
 So that has already been done
 for me on this controller.

0:04:00.880000 --> 0:04:03.560000
 So I'm going to be browsing
 to that IP address.

0:04:03.560000 --> 0:04:06.380000
 But beyond that, the controller
 is in a basic state.

0:04:06.380000 --> 0:04:10.280000
 It's going to present me with
 the initial setup wizard.

0:04:10.280000 --> 0:04:14.580000
 And I'm going to have to go through
 that in order to proceed.

0:04:14.580000 --> 0:04:21.660000
 All right, so I'm going to connect
 to my wireless LAN controller.

0:04:21.660000 --> 0:04:25.320000
 Now, the wireless LAN controller is presenting
 me with a digital certificate

0:04:25.320000 --> 0:04:30.380000
 for authentication purposes to
 give me a secure HTTP session.

0:04:30.380000 --> 0:04:34.780000
 The problem is that digital certificate
 is a self-signed authentication

0:04:34.780000 --> 0:04:39.100000
 certificate. And it's not been signed
 by some trusted root authority out

0:04:39.100000 --> 0:04:41.020000
 there on the internet.

0:04:41.020000 --> 0:04:44.700000
 So my browser right now is saying, hey,
 I see a digital certificate, but

0:04:44.700000 --> 0:04:50.040000
 it's signed and authenticated by the
 device that created itself, which

0:04:50.040000 --> 0:04:51.300000
 isn't really secure.

0:04:51.300000 --> 0:04:52.640000
 So it's given me a warning.

0:04:52.640000 --> 0:04:55.460000
 Some browsers, you couldn't
 get past this.

0:04:55.460000 --> 0:04:58.720000
 But fortunately for us, at
 least with Firefox, we can.

0:04:58.720000 --> 0:05:06.280000
 And so if I go to Advanced and I scroll
 down, I now have the ability to

0:05:06.280000 --> 0:05:08.520000
 accept the risk and continue.

0:05:08.520000 --> 0:05:10.200000
 So that's what I'm going to do.

0:05:10.200000 --> 0:05:15.260000
 All right, this has already been pre
-configured to have a username and

0:05:15.260000 --> 0:05:22.200000
 password of Cisco for both things.


0:05:22.200000 --> 0:05:35.500000
 And now after a few moments, we should
 see the initial setup wizard.

0:05:35.500000 --> 0:05:36.860000
 And there we are.

0:05:36.860000 --> 0:05:40.140000
 So now we're in the configuration
 setup wizard.

0:05:40.140000 --> 0:05:43.600000
 All right, so I'm going to leave
 this as a standalone controller.

0:05:43.600000 --> 0:05:46.320000
 It's not doing any kind of redundancy
 with anybody else.

0:05:46.320000 --> 0:05:47.720000
 I am in the United States.

0:05:47.720000 --> 0:05:55.260000
 I can go ahead and change the date
 to March 19th, because that's what

0:05:55.260000 --> 0:05:57.380000
 it is right now as I record this.

0:05:57.380000 --> 0:05:59.580000
 I'll just leave the time
 exactly as it is.

0:05:59.580000 --> 0:06:02.120000
 I'm not going to put
 in an NTP server.

0:06:02.120000 --> 0:06:07.040000
 Now scrolling down, wireless
 management settings.

0:06:07.040000 --> 0:06:16.120000
 So remember that as I drew, the
 controller had a console port.

0:06:16.120000 --> 0:06:18.880000
 It had a service port.

0:06:18.880000 --> 0:06:23.120000
 And then it had some data ports.

0:06:23.120000 --> 0:06:28.400000
 You know, and the quantity of data
 ports varies based on the platform.

0:06:28.400000 --> 0:06:33.080000
 And each one of these data ports could
 be configured with an IP address.

0:06:33.080000 --> 0:06:37.460000
 And whatever IP address you put on here,
 this would be an IP address that

0:06:37.460000 --> 0:06:40.700000
 your access points would actually join
 to when they're joining and creating

0:06:40.700000 --> 0:06:42.140000
 their CAPWAP tunnels.

0:06:42.140000 --> 0:06:45.660000
 So that's what's asking
 us to do right here.

0:06:45.660000 --> 0:06:49.720000
 It's asking us to select an interface,
 which is going to be one of these

0:06:49.720000 --> 0:06:54.000000
 guys. I'll just leave it to gigabit
 two, select what VLAN that's going

0:06:54.000000 --> 0:06:58.480000
 to be in, and put an IP address
 and mask on there.

0:06:58.480000 --> 0:06:59.740000
 So let's just go ahead
 and do that.

0:06:59.740000 --> 0:07:00.920000
 So I'm just going to select.

0:07:00.920000 --> 0:07:04.280000
 I'm going to put it in the
 default VLAN, VLAN one.

0:07:04.280000 --> 0:07:10.360000
 And I'm just going to give it some fake
 IP address about 192, 168, 1.100

0:07:10.360000 --> 0:07:18.640000
 or 101. Subnet mask
 255, 255, 255, 0.

0:07:18.640000 --> 0:07:21.640000
 Default gateway.

0:07:21.640000 --> 0:07:25.320000
 If I had a real default gateway,
 it would be something like this.

0:07:25.320000 --> 0:07:30.900000
 And I don't need to put
 in a DHCP server.

0:07:30.900000 --> 0:07:33.040000
 And I'm not going to be
 running IPv6 on this.

0:07:33.040000 --> 0:07:39.700000
 So now I can just move on.

0:07:39.700000 --> 0:07:44.480000
 All right. So now at this point, I
 could continue with next or I could

0:07:44.480000 --> 0:07:47.460000
 add just my basic preliminary
 wireless LAN.

0:07:47.460000 --> 0:07:49.800000
 So I'm going to show you how to add
 the wireless LAN with a pre shared

0:07:49.800000 --> 0:07:52.460000
 key here in the setup wizard.

0:07:52.460000 --> 0:07:55.380000
 And then once we're past the setup wizard
 and we had the full dashboard

0:07:55.380000 --> 0:07:59.980000
 to look at, we'll create another wireless
 LAN with a pre shared key.

0:07:59.980000 --> 0:08:03.120000
 So let's add one right here.

0:08:03.120000 --> 0:08:07.280000
 And we'll call this
 one corporate one.

0:08:07.280000 --> 0:08:11.600000
 We'll stick with WPA2 personal.

0:08:11.600000 --> 0:08:15.540000
 And I'll click the little eyeball
 here so you can see the key.

0:08:15.540000 --> 0:08:19.320000
 And we'll call the key Cisco 1234.


0:08:19.320000 --> 0:08:22.040000
 Probably not the safest
 key out there.

0:08:22.040000 --> 0:08:25.640000
 But for demonstration purposes,
 that'll work.

0:08:25.640000 --> 0:08:31.780000
 And add. And there it is.

0:08:31.780000 --> 0:08:34.360000
 We can see it right there.

0:08:34.360000 --> 0:08:37.520000
 Now we click next.

0:08:37.520000 --> 0:08:41.020000
 We don't have to mess around with the
 client density or any RF groups

0:08:41.020000 --> 0:08:43.860000
 or anything. We'll leave
 it to data and voice.

0:08:43.860000 --> 0:08:48.520000
 And now it's saying, okay, I'm going
 to generate a certificate that I

0:08:48.520000 --> 0:08:52.240000
 can push down to the access points because
 when the access points create

0:08:52.240000 --> 0:08:56.540000
 a cap web tunnel, they're going
 to need a digital certificate.

0:08:56.540000 --> 0:08:58.780000
 It's not going to be the
 same digital certificate.

0:08:58.780000 --> 0:09:02.580000
 I just got to do my HTTPS
 session to the to the GUI.

0:09:02.580000 --> 0:09:06.660000
 This is a different digital certificate
 used purely for the cap web purposes

0:09:06.660000 --> 0:09:09.780000
 to have an encrypted tunnel to
 pass that control traffic.

0:09:09.780000 --> 0:09:11.580000
 So do I want to generate
 a certificate?

0:09:11.580000 --> 0:09:14.140000
 Yes, probably. Otherwise capwaps
 can have a big problem.

0:09:14.140000 --> 0:09:17.580000
 We can just leave the
 key size to 2048.

0:09:17.580000 --> 0:09:19.820000
 We can leave the signature
 to Shaw one.

0:09:19.820000 --> 0:09:24.300000
 And let's put in a passphrase here that
 can be used to help generate that

0:09:24.300000 --> 0:09:25.000000
 digital certificate.

0:09:25.000000 --> 0:09:28.400000
 How about INE rocks?

0:09:28.400000 --> 0:09:29.420000
 Yeah, that sounds good.

0:09:29.420000 --> 0:09:31.100000
 We'll put that in there.

0:09:31.100000 --> 0:09:34.280000
 That looks good.

0:09:34.280000 --> 0:09:35.620000
 And then summary.

0:09:35.620000 --> 0:09:39.000000
 All right. There's everything
 we put in.

0:09:39.000000 --> 0:09:44.100000
 Finish. All right.

0:09:44.100000 --> 0:09:45.720000
 So now it's thinking about it.

0:09:45.720000 --> 0:09:47.220000
 It's thinking about, okay,
 is everything look good?

0:09:47.220000 --> 0:09:48.580000
 I just put into the setup wizard.

0:09:48.580000 --> 0:09:50.460000
 Hopefully it will.

0:09:50.460000 --> 0:09:53.960000
 And in just a moment, I should see
 the actual dashboard where have all

0:09:53.960000 --> 0:09:56.040000
 my options available to me.

0:09:56.040000 --> 0:10:03.560000
 Good. The configuration
 successfully applied.

0:10:03.560000 --> 0:10:04.420000
 Now it logged me out.

0:10:04.420000 --> 0:10:06.460000
 I'm going to log back in.

0:10:06.460000 --> 0:10:15.760000
 And this time I'm going to
 see the full dashboard.

0:10:15.760000 --> 0:10:20.260000
 And every wireless LAN controller has a
 different layout for their dashboard.

0:10:20.260000 --> 0:10:23.620000
 But once you've configured one, you should
 be able to find the appropriate

0:10:23.620000 --> 0:10:28.120000
 pull down windows and boxes to configure
 the same types of things in a

0:10:28.120000 --> 0:10:30.440000
 different one. So here we are.

0:10:30.440000 --> 0:10:33.240000
 It says I've already got one
 wireless LAN configured.

0:10:33.240000 --> 0:10:36.580000
 Currently there are no access points
 that are joined to this.

0:10:36.580000 --> 0:10:37.920000
 So there would be no clients.

0:10:37.920000 --> 0:10:41.360000
 And so now we're just going to complete
 this by configuring one more wireless

0:10:41.360000 --> 0:10:43.960000
 LAN with WPA2 pre shared key.

0:10:43.960000 --> 0:10:46.840000
 But now we're going to do it from
 the actual dashboard itself.

0:10:46.840000 --> 0:10:49.600000
 So here I would select
 configuration.

0:10:49.600000 --> 0:10:54.780000
 Under tags and profiles, I would
 select wireless lands.

0:10:54.780000 --> 0:11:00.980000
 Okay, it's already
 got corporate one.

0:11:00.980000 --> 0:11:05.780000
 Let's add another wireless LAN.

0:11:05.780000 --> 0:11:10.000000
 So by default, whatever you put in
 the profile name, it'll go down to

0:11:10.000000 --> 0:11:11.720000
 the SSID as well.

0:11:11.720000 --> 0:11:13.340000
 How about corporate?

0:11:13.340000 --> 0:11:17.440000
 Oh, how about INE keys?

0:11:17.440000 --> 0:11:22.740000
 There we go. Now, notice by default
 is disabled, which means that the

0:11:22.740000 --> 0:11:26.900000
 beacons from many access points that
 join will not advertise this wireless

0:11:26.900000 --> 0:11:30.680000
 LAN. I want to enable it.

0:11:30.680000 --> 0:11:33.140000
 Okay, and I want to
 broadcast the SSID.

0:11:33.140000 --> 0:11:36.540000
 I want my access points when they do
 get around to joining this via CAPWAP

0:11:36.540000 --> 0:11:40.300000
 to include this SSID
 in their beacons.

0:11:40.300000 --> 0:11:43.440000
 Now, right now there's
 no security.

0:11:43.440000 --> 0:11:46.820000
 So I need to go to the security group
 right here, the security tab.

0:11:46.820000 --> 0:11:50.900000
 It defaults to WPA with WPA2.

0:11:50.900000 --> 0:11:52.420000
 You can just leave it to that.

0:11:52.420000 --> 0:11:53.820000
 And this is real easy.

0:11:53.820000 --> 0:11:55.700000
 All we have to do.

0:11:55.700000 --> 0:11:59.800000
 Notice it defaults to AES
 CCMP for encryption.

0:11:59.800000 --> 0:12:00.660000
 That's what we want.

0:12:00.660000 --> 0:12:06.400000
 That's good. These other ones, these
 GCMPs, these are actually stronger,

0:12:06.400000 --> 0:12:10.860000
 but not all wireless clients like laptops,
 PCs and smartphones necessarily

0:12:10.860000 --> 0:12:17.800000
 support GCMP, whereas everything these
 days supports AES with CCMP.

0:12:17.800000 --> 0:12:20.940000
 So that's probably best
 to keep it that way.

0:12:20.940000 --> 0:12:27.780000
 So it defaults to WPA2 Enterprise, which
 is 802.1x, and I don't want that.

0:12:27.780000 --> 0:12:32.800000
 So I will deselect that, and
 I will select pre-shared key.

0:12:32.800000 --> 0:12:35.800000
 And then the last thing is it gives me
 the option to type in my pre-shared

0:12:35.800000 --> 0:12:42.280000
 key. So let's just
 type in INE12345.

0:12:42.280000 --> 0:12:46.580000
 Apply to device.

0:12:46.580000 --> 0:12:51.460000
 And now I have both wireless
 LANs ready to go.

0:12:51.460000 --> 0:12:55.700000
 So the moment that an access point reaches
 out via CapWap Discovery discovers

0:12:55.700000 --> 0:13:00.640000
 this controller and creates an encrypted
 CapWap control tunnel, it will

0:13:00.640000 --> 0:13:05.560000
 then learn of these two wireless LANs
 and start advertising them in its

0:13:05.560000 --> 0:13:11.520000
 beacons. So that concludes this section
 on configuring wireless LANs with

0:13:11.520000 --> 0:13:15.300000
 pre-shared key within a Cisco
 wireless LAN controller.

