WEBVTT

0:00:03.200000 --> 0:00:06.680000
 Welcome to this video in which we're
 going to be starting our talk about

0:00:06.680000 --> 0:00:11.780000
 Cisco iOS and then moving forward from
 here using Cisco iOS on vast majority

0:00:11.780000 --> 0:00:17.300000
 of our tasks and power points with
 securing iOS remote access.

0:00:17.300000 --> 0:00:21.160000
 Now as a precursor because this is
 part of the CCNA bootcamp which is

0:00:21.160000 --> 0:00:24.420000
 at the end of the learning path for
 CCNA, I'm assuming you've already

0:00:24.420000 --> 0:00:27.940000
 gone through the basics of
 Cisco iOS command line.

0:00:27.940000 --> 0:00:31.340000
 So we already know what the difference
 is between exec and privilege exec,

0:00:31.340000 --> 0:00:35.280000
 between configuration terminal and global
 config and you know how to move

0:00:35.280000 --> 0:00:40.420000
 backwards and forward in the basics
 of iOS, how to break out of config

0:00:40.420000 --> 0:00:44.260000
 mode back into privilege exec mode,
 some of the basic commands like show

0:00:44.260000 --> 0:00:48.660000
 run, show version, show IP interface
 brief, you've got all that down.

0:00:48.660000 --> 0:00:53.180000
 So let's just go a little bit deeper into
 that now with securing iOS remote

0:00:53.180000 --> 0:00:57.680000
 access. So what we're talking about
 here is how do I secure my Cisco iOS

0:00:57.680000 --> 0:01:03.900000
 devices so that only legitimate authorized
 network admins can get into

0:01:03.900000 --> 0:01:08.800000
 the command line, look around and
 configure and change things.

0:01:08.800000 --> 0:01:13.840000
 All right, so let's start by
 securing the enable password.

0:01:13.840000 --> 0:01:18.900000
 So we know that on Cisco devices without
 an enable password, without an

0:01:18.900000 --> 0:01:23.140000
 enable secret, basically the moment
 somebody gets in, for example, let's

0:01:23.140000 --> 0:01:24.520000
 just take a look.

0:01:24.520000 --> 0:01:34.220000
 So if I did not have it secured and
 I went into my device, for example

0:01:34.220000 --> 0:01:41.360000
 router one, okay, so here I am, if
 there was no security here, so this

0:01:41.360000 --> 0:01:46.720000
 is at exec mode right now, I could
 just type enable and then bam, I'm

0:01:46.720000 --> 0:01:51.160000
 in. So now I am at privilege exec level
 and privilege exec level is what

0:01:51.160000 --> 0:01:53.880000
 we call privilege level 15.

0:01:53.880000 --> 0:01:58.140000
 And at privilege level 15, because remember
 in Cisco iOS, different commands

0:01:58.140000 --> 0:02:00.120000
 are at different privilege levels.


0:02:00.120000 --> 0:02:04.240000
 And by default, if you don't move things
 around, if you don't change things,

0:02:04.240000 --> 0:02:08.980000
 privilege level 15 is where you
 have full access to everything.

0:02:08.980000 --> 0:02:13.560000
 And once you are in privilege exec mode,
 which is called enable mode by

0:02:13.560000 --> 0:02:20.180000
 a lot of people, you can do enable
 privilege level 15, which means you

0:02:20.180000 --> 0:02:20.720000
 can do anything.

0:02:20.720000 --> 0:02:23.980000
 You can type whatever
 show command you want.

0:02:23.980000 --> 0:02:27.860000
 You can get into configuration mode
 and start configuring the box.

0:02:27.860000 --> 0:02:30.840000
 Of course, you have to learn how to type
 on your T keyboard, which I clearly

0:02:30.840000 --> 0:02:32.340000
 don't know how to do.

0:02:32.340000 --> 0:02:35.080000
 And you can start messing
 around with it.

0:02:35.080000 --> 0:02:39.860000
 So the first logical place is that we
 want to make sure that when people

0:02:39.860000 --> 0:02:45.720000
 are right here, that they cannot get
 into privileged exec level without

0:02:45.720000 --> 0:02:51.400000
 a password. So historically speaking,
 the old way of doing that was the

0:02:51.400000 --> 0:02:54.440000
 enable password and then
 type a password.

0:02:54.440000 --> 0:02:58.300000
 But then we now use the enable secret,
 which encrypts the password so

0:02:58.300000 --> 0:03:01.000000
 that people can't
 read the password.

0:03:01.000000 --> 0:03:08.540000
 So just to demonstrate that.

0:03:08.540000 --> 0:03:15.040000
 So config T. So if I type an enable
 password of let's say Cisco, it does

0:03:15.040000 --> 0:03:18.660000
 the job. So now someone's
 trying to get in.

0:03:18.660000 --> 0:03:22.160000
 They can't unless they know the
 password of Cisco to get in.

0:03:22.160000 --> 0:03:25.440000
 The problem with that was if somebody
 looked at your show running config,

0:03:25.440000 --> 0:03:28.720000
 there it is in plain text
 for everybody to see.

0:03:28.720000 --> 0:03:30.860000
 We don't want that.

0:03:30.860000 --> 0:03:33.820000
 So no enable password Cisco.

0:03:33.820000 --> 0:03:36.460000
 The better way to do
 it was enable secret.

0:03:36.460000 --> 0:03:38.600000
 Enable secret Cisco.

0:03:38.600000 --> 0:03:40.560000
 We can use the exact
 same password.

0:03:40.560000 --> 0:03:42.740000
 It does the exact same thing.

0:03:42.740000 --> 0:03:44.080000
 Now someone's trying to get in.

0:03:44.080000 --> 0:03:46.240000
 They still need to know
 that password of Cisco.

0:03:46.240000 --> 0:03:48.760000
 And by the way, it
 is case sensitive.

0:03:48.760000 --> 0:03:51.200000
 So make sure if you're using uppercase
 and lowercase stuff, you remember

0:03:51.200000 --> 0:03:53.140000
 that. But here's the difference.

0:03:53.140000 --> 0:03:57.200000
 Now, if I look at my running config,
 you can't tell what my password was

0:03:57.200000 --> 0:04:01.560000
 because it's been hashed
 into an MD five digest.

0:04:01.560000 --> 0:04:06.220000
 So it's much better to use the enable
 secret instead of the enable password.

0:04:06.220000 --> 0:04:11.560000
 Also, if someone has physical access
 to your console port, we probably

0:04:11.560000 --> 0:04:16.360000
 want to password protect that as well
 by putting in a console password

0:04:16.360000 --> 0:04:18.960000
 online console zero.

0:04:18.960000 --> 0:04:26.180000
 Okay. So that if someone has physical
 access to your box and or remote

0:04:26.180000 --> 0:04:31.200000
 access to your box, that's the very
 basic starting point of protecting

0:04:31.200000 --> 0:04:34.920000
 it with an enable secret
 and a console password.

0:04:34.920000 --> 0:04:41.140000
 Now, by default, Cisco routers and switches,
 just because you put an IP

0:04:41.140000 --> 0:04:46.700000
 address on them are not automatically
 enabled for remote access.

0:04:46.700000 --> 0:04:51.560000
 So whether I've got an IP address on
 my box or not, by default, the only

0:04:51.560000 --> 0:04:56.540000
 way I can configure it is if I have
 physical access to the console port.

0:04:56.540000 --> 0:04:57.740000
 Well, that's all well and good.

0:04:57.740000 --> 0:05:00.920000
 If I'm right there in front of the
 router switch in the rack in front

0:05:00.920000 --> 0:05:04.320000
 of me, but most likely, you're going
 to want to be able to either tell

0:05:04.320000 --> 0:05:08.060000
 net or SSH into that box because
 you're not going to be there.

0:05:08.060000 --> 0:05:09.500000
 Right. You're going to be
 sitting at your desk.

0:05:09.500000 --> 0:05:11.900000
 You're going to be sitting at your home
 office and you're going to want

0:05:11.900000 --> 0:05:13.700000
 to get remote access to it.

0:05:13.700000 --> 0:05:14.720000
 So how do we do that?

0:05:14.720000 --> 0:05:19.320000
 Well, one way you can do
 it is by using telnet.

0:05:19.320000 --> 0:05:23.920000
 Now with telnet, basically telnet, the
 idea behind telnet is you can type

0:05:23.920000 --> 0:05:29.280000
 in your commands, but it's wrapped inside
 of an IP packet, which is wrapped

0:05:29.280000 --> 0:05:32.860000
 inside of, you know, TCP, which uses
 the telnet protocol to send your

0:05:32.860000 --> 0:05:37.440000
 commands. Downside to telnet is everything
 is sent like it says in clear

0:05:37.440000 --> 0:05:41.720000
 text. So if there's somebody sniffing
 packets between the two of you,

0:05:41.720000 --> 0:05:43.720000
 they can see everything
 you're typing.

0:05:43.720000 --> 0:05:46.920000
 They can see everything that router
 switch is sending back to you as a

0:05:46.920000 --> 0:05:48.880000
 result of the command
 you're typing.

0:05:48.880000 --> 0:05:50.480000
 So it's not secure.

0:05:50.480000 --> 0:05:55.240000
 So it's better to use something called
 secure shell, which like telnet

0:05:55.240000 --> 0:05:58.680000
 allows you to send commands back and
 forth between the router switch and

0:05:58.680000 --> 0:06:00.300000
 yourself. But here's
 the big difference.

0:06:00.300000 --> 0:06:02.180000
 Everything is encrypted.

0:06:02.180000 --> 0:06:05.700000
 So somebody was in the middle
 and capturing everything.

0:06:05.700000 --> 0:06:08.380000
 It wouldn't do them any good because
 they wouldn't be able to tell what

0:06:08.380000 --> 0:06:09.740000
 it is that you're sending.

0:06:09.740000 --> 0:06:11.120000
 It's all encrypted.

0:06:11.120000 --> 0:06:13.580000
 All right. So let's
 start with telnet.

0:06:13.580000 --> 0:06:16.780000
 How do we enable it for telnet
 if I want to do that?

0:06:16.780000 --> 0:06:18.940000
 If telnet is perfectly
 fine with me.

0:06:18.940000 --> 0:06:23.040000
 All right. So step number one, we're going
 to go to what's called a logical

0:06:23.040000 --> 0:06:26.660000
 interface called a virtual
 teletype interface.

0:06:26.660000 --> 0:06:28.920000
 That's what VTY stands for.

0:06:28.920000 --> 0:06:34.420000
 And in Cisco devices, typically they
 have at minimum five of these logical

0:06:34.420000 --> 0:06:37.620000
 interfaces, 0123 and four.

0:06:37.620000 --> 0:06:39.140000
 So that's five interfaces.

0:06:39.140000 --> 0:06:41.960000
 So we can configure them
 all simultaneously.

0:06:41.960000 --> 0:06:44.680000
 We're going to give
 them all a password.

0:06:44.680000 --> 0:06:46.640000
 And then we're going to say login.


0:06:46.640000 --> 0:06:48.820000
 Now, a lot of times you don't have
 to type login because it's already

0:06:48.820000 --> 0:06:49.840000
 there by default.

0:06:49.840000 --> 0:06:54.620000
 Let's take a look and see if
 that's true on our devices.

0:06:54.620000 --> 0:07:00.200000
 All right. So I'm going to say
 that we can configure anything.

0:07:00.200000 --> 0:07:06.000000
 All right. Let me take a step
 back here for a second.

0:07:06.000000 --> 0:07:12.580000
 Both telnet and SSH are protocols by
 which I can send IP packets to my

0:07:12.580000 --> 0:07:14.920000
 router, to my switch.

0:07:14.920000 --> 0:07:19.340000
 And then if that router or switch is
 configured for IP and is configured

0:07:19.340000 --> 0:07:24.700000
 to recognize and process telnet
 and SSH, it can respond to me.

0:07:24.700000 --> 0:07:28.980000
 In this case, I don't have any
 IP on these guys at all.

0:07:28.980000 --> 0:07:33.080000
 So I could go to my VTY lines, which
 are down here at the bottom.

0:07:33.080000 --> 0:07:38.300000
 All right. VTY lines.

0:07:38.300000 --> 0:07:43.460000
 And right now it's saying, okay, I am
 allowing telnet and SSH, but without

0:07:43.460000 --> 0:07:48.400000
 any IP address, without any passwords,
 I'm dead in the water.

0:07:48.400000 --> 0:07:52.360000
 So it doesn't really matter what your
 VTY line is configured for if you

0:07:52.360000 --> 0:07:54.020000
 don't have any IP addresses.

0:07:54.020000 --> 0:07:56.840000
 Show IP interface brief.

0:07:56.840000 --> 0:08:01.640000
 At a minimum, you have to have some
 interface that's got an IP address

0:08:01.640000 --> 0:08:05.180000
 on it that is in the up up state.

0:08:05.180000 --> 0:08:09.140000
 Got to start there before you even
 do the stuff that we're showing you

0:08:09.140000 --> 0:08:13.760000
 here on your VTY line.

0:08:13.760000 --> 0:08:18.100000
 But once your IP address is on an interface,
 once that interface is active,

0:08:18.100000 --> 0:08:23.080000
 once you can ping it from wherever you
 happen to be, now you can console

0:08:23.080000 --> 0:08:27.440000
 into that device and complete your
 configuration by doing this.

0:08:27.440000 --> 0:08:31.400000
 So go on to the VTY line, and there's
 a couple of ways you can do this.

0:08:31.400000 --> 0:08:36.780000
 Now, this method right here is saying,
 okay, I'm going to give the exact

0:08:36.780000 --> 0:08:40.760000
 same static password to all of
 my network administrators.

0:08:40.760000 --> 0:08:45.400000
 So whether I have two network admins
 or 20 network admins, I'm going to

0:08:45.400000 --> 0:08:49.200000
 tell them all that the
 password is Cisco.

0:08:49.200000 --> 0:08:53.500000
 So they just have to implement the telnet
 command on their application,

0:08:53.500000 --> 0:08:57.680000
 tell them about the IP address on my
 box, and then it'll prompt them for

0:08:57.680000 --> 0:09:03.540000
 a password. And that password will
 be a Cisco and they'll be in.

0:09:03.540000 --> 0:09:06.860000
 Another alternative is you could say,
 hey, I want to assign each of my

0:09:06.860000 --> 0:09:12.300000
 network admins their own unique
 username and password.

0:09:12.300000 --> 0:09:13.580000
 So they're all different.

0:09:13.580000 --> 0:09:18.700000
 So at that point, you would go to global
 configuration level, and you

0:09:18.700000 --> 0:09:27.120000
 could say username, maybe Bob and
 maybe privilege 15 password.

0:09:27.120000 --> 0:09:31.140000
 How about Bob 123.

0:09:31.140000 --> 0:09:36.580000
 And then we go on to our VTY lines
 again, which brings us down here to

0:09:36.580000 --> 0:09:42.040000
 config line, and instead of saying
 login, we say login local.

0:09:42.040000 --> 0:09:43.880000
 What's the difference?

0:09:43.880000 --> 0:09:49.640000
 Well, under your VTY line, when you
 say login, that tells the Cisco iOS

0:09:49.640000 --> 0:09:56.280000
 device to expect the password to be under
 the VTY line to be right there.

0:09:56.280000 --> 0:10:02.380000
 When you say login local, that tells the
 router or switch, hey, the username

0:10:02.380000 --> 0:10:07.920000
 and password is configured globally
 as a username password statement.

0:10:07.920000 --> 0:10:11.260000
 Look elsewhere for
 the credentials.

0:10:11.260000 --> 0:10:16.460000
 So that's the basics of configuring
 telnet access.

0:10:16.460000 --> 0:10:22.920000
 So once again, just to review, I need to
 go on to my device and at a minimum.

0:10:22.920000 --> 0:10:25.840000
 I guess I need to get out of here.


0:10:25.840000 --> 0:10:34.020000
 I need to go into some interface like
 gigabit 00 put in some IP address.

0:10:34.020000 --> 0:10:36.960000
 And subnet mask.

0:10:36.960000 --> 0:10:39.400000
 Make sure the interface is up.

0:10:39.400000 --> 0:10:46.860000
 Then I can either type line VTY zero,
 you know, four and say password,

0:10:46.860000 --> 0:10:50.900000
 put in my password login.

0:10:50.900000 --> 0:10:54.860000
 And now everybody that logs in via telnet,
 they're going to have the exact

0:10:54.860000 --> 0:11:01.620000
 same password, Cisco,
 or no password Cisco.

0:11:01.620000 --> 0:11:06.140000
 Instead, I could put
 in a username.

0:11:06.140000 --> 0:11:09.820000
 You know, admin one.

0:11:09.820000 --> 0:11:13.560000
 Privilege 15. Now, what's
 the privilege 15 do?

0:11:13.560000 --> 0:11:21.360000
 If I leave off privilege 15, if I said
 instead username admin one password

0:11:21.360000 --> 0:11:26.760000
 Cisco, what that would do is when somebody
 tried to tell that in, they

0:11:26.760000 --> 0:11:31.160000
 would get a username prompt and they
 would type admin one, they would

0:11:31.160000 --> 0:11:33.080000
 get a password prompt.

0:11:33.080000 --> 0:11:37.840000
 They would type Cisco and that would
 put them at the exec level.

0:11:37.840000 --> 0:11:42.180000
 That would put them right here.

0:11:42.180000 --> 0:11:47.600000
 Now they would still have to type enable
 type in the enable password to

0:11:47.600000 --> 0:11:49.380000
 get into privilege exec level.

0:11:49.380000 --> 0:11:58.700000
 However, if I do it this way, username
 admin two privilege 15.

0:11:58.700000 --> 0:12:03.120000
 And now I say password,
 whatever it is, Cisco.

0:12:03.120000 --> 0:12:08.580000
 Now, if somebody logs in and they type
 admin two and Cisco is a password,

0:12:08.580000 --> 0:12:13.800000
 they will immediately be put
 into privilege exec level.

0:12:13.800000 --> 0:12:15.620000
 They will not have to type enable.


0:12:15.620000 --> 0:12:17.740000
 They will not have to type
 the enable password.

0:12:17.740000 --> 0:12:22.820000
 They are automatically granted
 privilege level 15 access.

0:12:22.820000 --> 0:12:27.540000
 That's the difference of what will
 happen if you include privilege 15

0:12:27.540000 --> 0:12:32.600000
 versus if you don't include
 privilege 15.

0:12:32.600000 --> 0:12:36.400000
 Now, like I said, you probably don't
 want to enable telnet access because

0:12:36.400000 --> 0:12:38.080000
 telnet is not encrypted.

0:12:38.080000 --> 0:12:39.420000
 It's not secure.

0:12:39.420000 --> 0:12:45.160000
 So we probably want to give our users
 SSH access instead, which is secure.

0:12:45.160000 --> 0:12:49.160000
 Now, in order to configure SSH in our
 device, we need, once again, we

0:12:49.160000 --> 0:12:52.000000
 still need an IP address on
 a functional interface.

0:12:52.000000 --> 0:12:55.520000
 That's our basic prerequisite, but
 we need a few additional things.

0:12:55.520000 --> 0:12:59.140000
 If your device does not already have
 a host name, you'll want to give

0:12:59.140000 --> 0:13:02.900000
 it a host name. You'll want to give
 it a domain name and you can just

0:13:02.900000 --> 0:13:04.080000
 make up the domain name.

0:13:04.080000 --> 0:13:07.440000
 If you don't have a real domain name
 like Cisco.com, I need that.

0:13:07.440000 --> 0:13:09.320000
 You could say my router.com.

0:13:09.320000 --> 0:13:13.800000
 It just needs that and that needs to
 have a cryptographic key because

0:13:13.800000 --> 0:13:16.920000
 remember SSH is doing
 everything encrypted.

0:13:16.920000 --> 0:13:18.540000
 Everything you're sending
 is being encrypted.

0:13:18.540000 --> 0:13:22.200000
 So both sides need
 a key to do that.

0:13:22.200000 --> 0:13:26.280000
 So how do we actually
 accomplish this?

0:13:26.280000 --> 0:13:32.500000
 Here we go. Host name, my router, IP
 domain name, you know, I need.com.

0:13:32.500000 --> 0:13:37.540000
 And then for your key, the absolute
 most basic fundamental way to create

0:13:37.540000 --> 0:13:42.120000
 the key is crypto
 key generate RSA.

0:13:42.120000 --> 0:13:45.760000
 And that will generate
 an RSA key for you.

0:13:45.760000 --> 0:13:51.480000
 Now, one thing to be familiar with is
 that when you do crypto key generate

0:13:51.480000 --> 0:13:55.680000
 RSA, let's go ahead and do that real
 quick so you can see what that looks

0:13:55.680000 --> 0:14:03.920000
 like. All right, so host
 name, let's just say R1.

0:14:03.920000 --> 0:14:09.520000
 Domain, let's say, I need.com.

0:14:09.520000 --> 0:14:19.980000
 Okay, and now we'll say
 crypto key generate RSA.

0:14:19.980000 --> 0:14:21.480000
 Oh, okay, I guess it ended.

0:14:21.480000 --> 0:14:23.860000
 So I did domain wrong.

0:14:23.860000 --> 0:14:25.800000
 So you don't do domain.

0:14:25.800000 --> 0:14:29.980000
 So no domain, that's
 something else.

0:14:29.980000 --> 0:14:31.260000
 That's not creating a domain name.


0:14:31.260000 --> 0:14:38.240000
 You all say IP domain dash name.

0:14:38.240000 --> 0:14:40.040000
 Now we can do I need.com.

0:14:40.040000 --> 0:14:41.720000
 That's the correct way to do it.

0:14:41.720000 --> 0:14:45.640000
 And notice it wouldn't even allow me
 to create the crypto key unless I

0:14:45.640000 --> 0:14:47.660000
 had a domain name first.

0:14:47.660000 --> 0:14:51.040000
 Now I can redo that command.

0:14:51.040000 --> 0:14:55.700000
 Now, notice it's saying by default,
 it's going to give me a crypto key

0:14:55.700000 --> 0:15:01.800000
 that is 512 bytes long or
 actually 512 bits long.

0:15:01.800000 --> 0:15:06.680000
 A lot of times there's some protocols
 and things and like SSH and certain

0:15:06.680000 --> 0:15:09.440000
 versions of SSH that
 won't work correctly.

0:15:09.440000 --> 0:15:14.140000
 If your key is that small, so you really
 should create a key of at least

0:15:14.140000 --> 0:15:20.460000
 1024 bits for all the versions
 of SSH to work.

0:15:20.460000 --> 0:15:26.240000
 And you can see it was very, very
 fast and it created that key.

0:15:26.240000 --> 0:15:34.480000
 So as a best practice, when you do
 crypto key generate RSA, don't let

0:15:34.480000 --> 0:15:36.100000
 it to just default to 512.

0:15:36.100000 --> 0:15:41.060000
 You want to increase that to
 1024 at an absolute minimum.

0:15:41.060000 --> 0:15:44.900000
 And then lastly, we want to configure
 our VTY lines for password usage

0:15:44.900000 --> 0:15:48.980000
 like before. So I already created.


0:15:48.980000 --> 0:15:53.160000
 Oops, should run.

0:15:53.160000 --> 0:15:55.620000
 So I already created in here.

0:15:55.620000 --> 0:16:00.560000
 My username and password
 statements.

0:16:00.560000 --> 0:16:09.260000
 So I still want to go to line
 VTY 04 and say login local.

0:16:09.260000 --> 0:16:15.680000
 Okay, so I still want to do that so
 that it will use that username and

0:16:15.680000 --> 0:16:23.600000
 password I've configured
 previously.

0:16:23.600000 --> 0:16:28.320000
 And then lastly, we want
 to go on to our VTY line.

0:16:28.320000 --> 0:16:32.680000
 And we want to tell it don't do.

0:16:32.680000 --> 0:16:38.160000
 Tell that just do SSH and that's what
 that transport input command says

0:16:38.160000 --> 0:16:48.740000
 transport input says, Hey, this is
 why I'm allowing as remote access.

0:16:48.740000 --> 0:16:53.760000
 Notice that by default, well, not necessarily
 by default, but if we look

0:16:53.760000 --> 0:16:55.880000
 under our VTY lines.

0:16:55.880000 --> 0:17:01.740000
 We can see here, it says transport
 input telnet SSH.

0:17:01.740000 --> 0:17:08.060000
 That means that, okay, both SSH and
 telnet are allowed to come in here.

0:17:08.060000 --> 0:17:16.060000
 Or you could say line VTY 04, you could
 say transport input all, which

0:17:16.060000 --> 0:17:17.200000
 allows everything.

0:17:17.200000 --> 0:17:23.700000
 But to be the most secure, we want to say
 transport input SSH, which excludes

0:17:23.700000 --> 0:17:31.620000
 telnet. Now, one other thing I want to
 mention here, which doesn't really

0:17:31.620000 --> 0:17:36.780000
 have anything to do with remote access
 methods per se, but it does have

0:17:36.780000 --> 0:17:39.200000
 to do with a lab task.

0:17:39.200000 --> 0:17:43.620000
 Should you choose to do it that applies
 some of these concepts, which

0:17:43.620000 --> 0:17:48.180000
 is about saving and reverting
 your configs.

0:17:48.180000 --> 0:17:51.540000
 A lot of times when people are first
 learning about iOS, they learn that,

0:17:51.540000 --> 0:17:57.580000
 Oh, to save my config, I simply do copy
 running dash config startup dash

0:17:57.580000 --> 0:18:02.640000
 config. Or simpler way is just doing
 copy run start, or even simpler than

0:18:02.640000 --> 0:18:06.020000
 that, right, mem, or just WR.

0:18:06.020000 --> 0:18:08.780000
 They all do the exact same thing.

0:18:08.780000 --> 0:18:17.880000
 If I go into my device, whether I do copy
 running config to startup config,

0:18:17.880000 --> 0:18:22.860000
 that does the exact same
 thing as just WR.

0:18:22.860000 --> 0:18:26.700000
 It takes your running config and
 saves it to your startup config.

0:18:26.700000 --> 0:18:29.160000
 Well, you can certainly do that
 and you should do that.

0:18:29.160000 --> 0:18:33.460000
 But sometimes, especially in lab environments
 when you're playing around,

0:18:33.460000 --> 0:18:39.200000
 you might want to have multiple
 copies of your config saved.

0:18:39.200000 --> 0:18:43.840000
 Like maybe I'm doing a BGP lab and everything
 I've got right now is applicable

0:18:43.840000 --> 0:18:49.100000
 to the BGP lab. So I want to
 save that as a BGP config.

0:18:49.100000 --> 0:18:54.860000
 And then I want to create another
 config for maybe a telnet lab.

0:18:54.860000 --> 0:18:57.760000
 And I want to save that
 as a different name.

0:18:57.760000 --> 0:18:59.960000
 Well, how do you do that?

0:18:59.960000 --> 0:19:04.440000
 Well, here you can see, you can say
 copy running dash config and instead

0:19:04.440000 --> 0:19:07.880000
 of saving it to envy ram as your startup
 config, you can see, you can

0:19:07.880000 --> 0:19:12.400000
 save it to flash memory and save it
 as a different name, like Keith dash

0:19:12.400000 --> 0:19:16.800000
 config. I could do
 that right here.

0:19:16.800000 --> 0:19:23.600000
 I could say copy my running
 config to flash colon.

0:19:23.600000 --> 0:19:28.720000
 Why don't we call it telnet lab.

0:19:28.720000 --> 0:19:31.100000
 And it'll say, okay, is this
 what you want to call it?

0:19:31.100000 --> 0:19:34.700000
 Telnet lab, I'll hit
 enter for yes.

0:19:34.700000 --> 0:19:38.140000
 And now it is stored in
 flash memory as that.

0:19:38.140000 --> 0:19:42.360000
 And I can view that by saying
 directory flash colon.

0:19:42.360000 --> 0:19:48.600000
 And you can see that here we have a
 lot of different configs pre saved

0:19:48.600000 --> 0:19:53.060000
 for various different
 labs that you can use.

0:19:53.060000 --> 0:19:56.860000
 Now the next logical question is, okay,
 after I've saved this config,

0:19:56.860000 --> 0:20:01.620000
 if I want to come back in the future,
 how do I load that config back?

0:20:01.620000 --> 0:20:07.720000
 The way you accomplish that is with
 the config replace command.

0:20:07.720000 --> 0:20:11.900000
 So notice at privileged exec level
 or enable mode, you can say config

0:20:11.900000 --> 0:20:14.260000
 replace flash colon.

0:20:14.260000 --> 0:20:16.360000
 So this is where is
 the config store?

0:20:16.360000 --> 0:20:18.860000
 Is it envy ram colon flash colon?

0:20:18.860000 --> 0:20:22.680000
 Maybe TFTP colon if it's stored
 on a remote TFTP server.

0:20:22.680000 --> 0:20:25.040000
 And then you give it the
 name of the config.

0:20:25.040000 --> 0:20:29.460000
 Now what config replace does
 is just like it sounds.

0:20:29.460000 --> 0:20:35.900000
 It completely swaps or replaces your
 current running config with a config

0:20:35.900000 --> 0:20:37.320000
 that you're specifying.

0:20:37.320000 --> 0:20:41.080000
 So like in this case, you'll say,
 are you sure you wish to proceed?

0:20:41.080000 --> 0:20:44.360000
 Because it's going to completely overwrite
 everything in your current

0:20:44.360000 --> 0:20:48.740000
 config. All your IP addresses everything
 with the config that you're replacing

0:20:48.740000 --> 0:20:53.760000
 it with. So if you say yes, it
 will actually swap it out.

0:20:53.760000 --> 0:20:58.720000
 And in most of our lab tasks, that's
 what we are going to ask you to do.

0:20:58.720000 --> 0:21:03.080000
 We're going to ask you to load or use
 the config replace command to replace

0:21:03.080000 --> 0:21:07.620000
 a config. So for example, if I want
 to load this config called ACL dash

0:21:07.620000 --> 0:21:15.700000
 lab, I would just say config replace
 flash colon ACL dash lab.

0:21:15.700000 --> 0:21:19.360000
 It says, are you sure
 you want to do it?

0:21:19.360000 --> 0:21:21.740000
 I would say why for yes.

0:21:21.740000 --> 0:21:28.240000
 And now it loads the config.

0:21:28.240000 --> 0:21:33.560000
 And now if we issue the show run command,
 we can see that everything's

0:21:33.560000 --> 0:21:39.440000
 different. I've got some IP addresses
 in there that I didn't have before.

0:21:39.440000 --> 0:21:44.560000
 I have some routing protocols in there
 that I didn't have before OSPF.

0:21:44.560000 --> 0:21:48.540000
 And so that's how you load
 a pre saved config.

0:21:48.540000 --> 0:21:53.920000
 And that concludes this
 section on Cisco iOS.

0:21:53.920000 --> 0:21:56.440000
 Configuring basic remote access.

