WEBVTT

0:00:09.380000 --> 0:00:14.520000
 Hello and welcome to this video which
 is testing you on your Cisco CCNA

0:00:14.520000 --> 0:00:20.180000
 IPB6 addressing and
 subnetting concepts.

0:00:20.180000 --> 0:00:22.980000
 Question number one.

0:00:22.980000 --> 0:00:29.120000
 How many bits does an
 IPB6 address consume?

0:00:29.120000 --> 0:00:34.800000
 The correct answer is 128 bits.

0:00:34.800000 --> 0:00:41.520000
 An IPB6 address is four times
 as large as an IPB4 address.

0:00:41.520000 --> 0:00:51.920000
 Question two. What is the full expanded
 version of the IPB6 address shown

0:00:51.920000 --> 0:00:56.940000
 here? So what you see here
 is an abbreviated address.

0:00:56.940000 --> 0:01:00.120000
 What would that address look like
 if it was not abbreviated?

0:01:00.120000 --> 0:01:13.280000
 And the correct answer is C.

0:01:13.280000 --> 0:01:21.740000
 Question three. Which of the following
 answers represents the shortest

0:01:21.740000 --> 0:01:25.720000
 way one could abbreviate the
 IPB6 address that follows?

0:01:25.720000 --> 0:01:29.020000
 So here you see a fully
 expanded IPB6.

0:01:29.020000 --> 0:01:33.620000
 Now you're asked to abbreviate this
 to represent it as short with as few

0:01:33.620000 --> 0:01:35.580000
 characters as possible.

0:01:35.580000 --> 0:01:43.160000
 The correct answer is D.

0:01:43.160000 --> 0:01:48.520000
 Remember that double colons can only
 show once in an IPB6 address.

0:01:48.520000 --> 0:01:53.100000
 That's why answers B and C are incorrect
 because they have the double

0:01:53.100000 --> 0:01:55.400000
 colon more than once.

0:01:55.400000 --> 0:02:03.200000
 Answer A technically is correct as far
 as one way that you can abbreviate

0:02:03.200000 --> 0:02:07.040000
 it but it is not the shortest way you
 could abbreviate it and this question

0:02:07.040000 --> 0:02:13.360000
 was asking for the shortest
 way which is answer D.

0:02:13.360000 --> 0:02:23.820000
 Question four. Maps the following IPB6
 addresses to their respective type

0:02:23.820000 --> 0:02:33.340000
 identification. And here
 are the answers.

0:02:33.340000 --> 0:02:38.100000
 Every IPB6 address that begins with
 FE80 is a link local address.

0:02:38.100000 --> 0:02:40.840000
 Regardless of what follows
 that pattern.

0:02:40.840000 --> 0:02:45.000000
 Multicast addresses always
 begin with FF.

0:02:45.000000 --> 0:02:49.440000
 If an address begins with a two or three
 that is a global unicast address

0:02:49.440000 --> 0:02:57.760000
 and every address that begins with an
 FC or an FD is a unique local address.

0:02:57.760000 --> 0:03:09.160000
 Question five. What subnet mask is
 strongly recommended to be applied

0:03:09.160000 --> 0:03:19.040000
 to IPB6 subnets where end user
 devices and VLANs reside?

0:03:19.040000 --> 0:03:24.400000
 That would be a slash 64.

0:03:24.400000 --> 0:03:36.100000
 Question six. Your company is given
 the IPB6 network of 2006 colon 111

0:03:36.100000 --> 0:03:42.420000
 colon 2222 colon colon slash 48
 from your service provider.

0:03:42.420000 --> 0:03:46.820000
 You wish to divide this into subnets
 with each subnet containing a slash

0:03:46.820000 --> 0:03:52.880000
 64 net mask. Given the above information
 what will be the address of your

0:03:52.880000 --> 0:04:04.620000
 22nd subnet? In this case the answer
 is A and just to help you work that

0:04:04.620000 --> 0:04:12.740000
 out. So we know here that in this particular
 case that all the IPB6 addresses

0:04:12.740000 --> 0:04:20.360000
 will begin with 1222.

0:04:20.360000 --> 0:04:23.060000
 Those are the first 48 bits.

0:04:23.060000 --> 0:04:28.480000
 Now the next word before you get to
 the colon is going to bring it out

0:04:28.480000 --> 0:04:33.960000
 to 64 bits. So that next word the very
 first network the very first subnet

0:04:33.960000 --> 0:04:38.340000
 would be 000 colon colon slash 64.


0:04:38.340000 --> 0:04:40.500000
 That's the first subnet.

0:04:40.500000 --> 0:04:50.600000
 The second subnet will be 0001.

0:04:50.600000 --> 0:04:54.200000
 That's the second subnet
 colon colon slash 64.

0:04:54.200000 --> 0:04:57.160000
 Then the third subnet
 will be 0002.

0:04:57.160000 --> 0:04:59.720000
 So hopefully you see at
 this point a pattern.

0:04:59.720000 --> 0:05:02.320000
 The subnet is one less.

0:05:02.320000 --> 0:05:06.700000
 So for example if I was to say what's
 the fourth subnet it would be 0003.

0:05:06.700000 --> 0:05:08.740000
 What's the ninth subnet?

0:05:08.740000 --> 0:05:13.820000
 0008. But we're asked
 for the 22nd subnet.

0:05:13.820000 --> 0:05:18.360000
 So you might think oh well
 that would be 00021.

0:05:18.360000 --> 0:05:21.840000
 But remember IPB6 addresses
 are in hex.

0:05:21.840000 --> 0:05:26.600000
 So you have to ask yourself
 what is 21 in hexadecimal?

0:05:26.600000 --> 0:05:31.500000
 Well in hexadecimal 21 is 1.

0:05:31.500000 --> 0:05:36.660000
 That would be 16 plus 5.

0:05:36.660000 --> 0:05:41.220000
 So remember these octets here the
 first one is the ones position.

0:05:41.220000 --> 0:05:45.500000
 Each one of these can have
 0 through f in them.

0:05:45.500000 --> 0:05:54.420000
 So 000f that is the number 15
 which is our 16th subnet.

0:05:54.420000 --> 0:05:56.160000
 Remember it started at 000.

0:05:56.160000 --> 0:05:59.200000
 So 000f which is 15 that's
 our 16th subnet.

0:05:59.200000 --> 0:06:02.740000
 So our 17th subnet now has to
 move into the next position.

0:06:02.740000 --> 0:06:04.580000
 That's the 17th subnet.

0:06:04.580000 --> 0:06:08.860000
 That's actually 0010
 that's 16 in hex.

0:06:08.860000 --> 0:06:12.840000
 0010 in hex is 16 in decimal.

0:06:12.840000 --> 0:06:19.020000
 So 16 plus 5 gives us 22.

0:06:19.020000 --> 0:06:35.840000
 Actually that gives us 21.

0:06:35.840000 --> 0:06:47.680000
 Question 7. Given the IPB6 address
 of 2001 colon 2222 colon colon 1A33

0:06:47.680000 --> 0:06:50.180000
 colon 555 slash 64.

0:06:50.180000 --> 0:06:58.540000
 What portion of this address is denoted
 by colon colon 1A33 colon 555.

0:06:58.540000 --> 0:07:07.400000
 Well that last part of the address
 would be the interface identifier.

0:07:07.400000 --> 0:07:11.360000
 In the world of IPB4 we would
 call those the host bits.

0:07:11.360000 --> 0:07:16.480000
 But this is IPB6 and the
 name is the interface ID.

0:07:16.480000 --> 0:07:26.840000
 Question 8. Which of the following is
 the correct command to add the IPB6

0:07:26.840000 --> 0:07:32.500000
 address that you see here to interface
 gig 00 along with a slash 64 net

0:07:32.500000 --> 0:07:40.460000
 mask? The correct answer is C.

0:07:40.460000 --> 0:07:46.060000
 This is an interface level command
 that starts with IPB6 address.

0:07:46.060000 --> 0:07:59.060000
 Question 9. Interface
 gig 00 on router 2.

0:07:59.060000 --> 0:08:03.840000
 R2 contains the MAC address
 that you see right there.

0:08:03.840000 --> 0:08:06.920000
 This interface has been configured
 with the following command.

0:08:06.920000 --> 0:08:14.380000
 IPB6 address 2001 colon 2 colon
 colon slash 64 EUI dash 64.

0:08:14.380000 --> 0:08:19.560000
 Which of the following answers display
 the full IPB6 address that will

0:08:19.560000 --> 0:08:22.220000
 be applied to this interface?

0:08:22.220000 --> 0:08:30.240000
 And the correct answer is E.

0:08:30.240000 --> 0:08:35.240000
 So this question was testing whether
 or not you could remember how the

0:08:35.240000 --> 0:08:40.060000
 EUI 64 interface ID works when creating
 a dynamic interface ID.

0:08:40.060000 --> 0:08:46.500000
 And remember EUI 64 takes as a basis
 the MAC address of an interface.

0:08:46.500000 --> 0:08:51.140000
 Takes that MAC address splits
 it right in half.

0:08:51.140000 --> 0:08:58.100000
 So it would be 2022
 colon FA puts F.F.

0:08:58.100000 --> 0:09:06.560000
 colon F.E. So that expands it
 from a 48 bit to a 64 bit.

0:09:06.560000 --> 0:09:07.600000
 But that's not all.

0:09:07.600000 --> 0:09:10.840000
 So if you would just stop there you
 probably would have thought that one

0:09:10.840000 --> 0:09:14.920000
 of these other answers for example
 D you probably would have picked D

0:09:14.920000 --> 0:09:19.460000
 as the correct answer.

0:09:19.460000 --> 0:09:22.540000
 But actually you probably would have
 picked C as the correct answer.

0:09:22.540000 --> 0:09:27.300000
 But the problem with this is the other
 thing it does is it goes into the

0:09:27.300000 --> 0:09:29.500000
 very first octet.

0:09:29.500000 --> 0:09:37.620000
 So 2 0 is our first octet and it changes
 the seventh bit of that octet.

0:09:37.620000 --> 0:09:40.700000
 So if we have the
 octet right here.

0:09:40.700000 --> 0:09:52.060000
 So 0 0 1 0 that's 2 0
 0 0 0 so that's 2 0.

0:09:52.060000 --> 0:09:55.440000
 It changes this bit right
 here it flips it.

0:09:55.440000 --> 0:10:01.600000
 So you would end up
 with 0 0 1 0 0 1 0.

0:10:01.600000 --> 0:10:11.100000
 So now instead of being 2 0 2
 2 you have 2 2 2 2 colon F.F.

0:10:11.100000 --> 0:10:19.340000
 colon F.E. F.B. which gets you to
 this correct answer right here.

0:10:19.340000 --> 0:10:32.720000
 Question 10. What command must
 exist on a Cisco router?

0:10:32.720000 --> 0:10:36.920000
 So that router can be enabled with a
 dynamic IPv6 routing protocol such

0:10:36.920000 --> 0:10:40.060000
 as OSPF or EIGRP.

0:10:40.060000 --> 0:10:52.460000
 And that would be the global configuration
 command IPv6 unicast-routing.

0:10:52.460000 --> 0:11:02.520000
 Question 11. Which of the following
 is a stateful method for providing

0:11:02.520000 --> 0:11:11.100000
 dynamic IPv6 addresses to host?

0:11:11.100000 --> 0:11:13.980000
 And that would be DHCP version 6.

0:11:13.980000 --> 0:11:21.340000
 Now Slack can also provide dynamic
 IPv6 addresses to host but that is

0:11:21.340000 --> 0:11:24.480000
 stateless that is not stateful.

0:11:24.480000 --> 0:11:29.020000
 Only DHCP v6 is stateful.

0:11:29.020000 --> 0:11:38.460000
 Question 12. Which of the following
 statements about packets addressed

0:11:38.460000 --> 0:11:42.520000
 with IPv6 link local
 addresses are true?

0:11:42.520000 --> 0:11:44.640000
 Select two answers.

0:11:44.640000 --> 0:11:52.980000
 Well packets addressed with link local
 addresses will start with the well

0:11:52.980000 --> 0:11:54.740000
-known pattern of F.E.80.

0:11:54.740000 --> 0:11:58.720000
 So that's how you recognize a link
 local address by that pattern.

0:11:58.720000 --> 0:12:03.280000
 And the link local address of a
 node is automatically generated.

0:12:03.280000 --> 0:12:05.580000
 You don't have to type
 it in or configure it.

0:12:05.580000 --> 0:12:07.840000
 It's automatically generated.

0:12:07.840000 --> 0:12:12.420000
 The rest of these
 answers are false.

0:12:12.420000 --> 0:12:25.500000
 Question 13. What Cisco iOS command
 enables IPv6 processing as well as

0:12:25.500000 --> 0:12:32.060000
 a link local address on an interface,
 but adds no other unicast IPv6 address

0:12:32.060000 --> 0:12:34.080000
 to that interface.

0:12:34.080000 --> 0:12:38.500000
 In other words, if you want to enable
 IPv6 processing on an interface

0:12:38.500000 --> 0:12:43.920000
 so that it could send and receive IPv6
 packets, but you did not want to

0:12:43.920000 --> 0:12:48.700000
 configure an IPv6 address on that interface,
 which of these commands would

0:12:48.700000 --> 0:12:54.060000
 do that for you?

0:12:54.060000 --> 0:12:57.760000
 And that is simply the
 command IPv6 enable.

0:12:57.760000 --> 0:13:01.740000
 As soon as you type that, a link local
 address will be dynamically generated

0:13:01.740000 --> 0:13:07.600000
 and IPv6 processing will be
 enabled on that interface.

0:13:07.600000 --> 0:13:21.100000
 Question 14. Match the following IPv6
 multicast addresses with their usage.

0:13:21.100000 --> 0:13:32.320000
 And here are the correct
 answers for those.

0:13:32.320000 --> 0:13:42.980000
 Question 15. Which of the following
 is an IPv6 multicast address that

0:13:42.980000 --> 0:13:47.020000
 is bounded by a site local scope?

0:13:47.020000 --> 0:13:53.580000
 And the answer is C.

0:13:53.580000 --> 0:14:00.700000
 Remember, after the FF0, the very next
 number, that fourth number denotes

0:14:00.700000 --> 0:14:04.440000
 the scope of an IPv6
 multicast address.

0:14:04.440000 --> 0:14:08.540000
 And if that number is a five, that means
 that multicast address can travel

0:14:08.540000 --> 0:14:14.640000
 within your site, but no further.

0:14:14.640000 --> 0:14:27.840000
 Question 16. Which of the following represents
 the IPv6 loopback address?

0:14:27.840000 --> 0:14:39.040000
 And that would be answer
 B colon colon one.

0:14:39.040000 --> 0:14:44.060000
 And that brings us to the end of this
 self-assessment for IPv6 within

0:14:44.060000 --> 0:14:47.500000
 the category of network
 fundamentals for CCNA.

0:14:47.500000 --> 0:14:48.200000
 Thank you for watching.

